CreatBot PEEK-300 3D Printer User Manual

CreatBot LogoCreatBot PEEK 300 3D PrinterCreatBot PEEK-250
User manual
English V1.0
Henan Creatbot Technology Limited

PEEK-300 3D Printer

Icon conventions
CreatBot PEEK 300 3D Printer - Icon Tip icon to remind users to have a good method or technique.
CreatBot PEEK 300 3D Printer - Icon 1 Note icon, to remind the user must be given adequate attention.
CreatBot PEEK 300 3D Printer - Icon 2 Prohibition icons, prevents users from unauthorized operation.

Notice

Read First
Thank you for choosing CreatBot 3D printer!
This manual contains important information about the installation, use, maintenance and common problems of CreatBot 3D printer. Please read this manual carefully before using 3D printer. All losses caused by the breach of the notes and the operation process of the operation process will be borne by the user.
Please use the filament provided by CreatBot, or high quality filament by third manufacturers. Due to the use of third party inferior material caused by the failure of the printer, the loss will be borne by the user.
Software running environment, 2G or above processors, at least 1G memory, compatible with Windows, MAC, or Linux, please use memory as much as possible.
I wish you have fun with CreatBot 3D printer!
Danger Warning
CreatBot PEEK 300 3D Printer - Icon 3 The nozzle’s temperature will reach 420 degrees, don’t touch.
CreatBot PEEK 300 3D Printer - Icon 4 The platform’s temperature will reach 100 degrees, don’t touch.
CreatBot PEEK 300 3D Printer - Icon 5 Please make sure that the printer connected to the ground.
CreatBot PEEK 300 3D Printer - Icon 6 Do not attempt to open the case, be careful of electric shock.
Working Environment
CreatBot PEEK 300 3D Printer - Icon 7 The 3D printer can work in the indoor environment of 5 ℃ to 30 ℃.
CreatBot PEEK 300 3D Printer - Icon 8 Long-term not use of the printer, be sure to keep off dust, moisture.
CreatBot PEEK 300 3D Printer - Icon 9 Long-term not use of the filament, please be sealed to prevent deterioration.

Machine Diagram

CreatBot PEEK 300 3D Printer - Machine DiagramCreatBot PEEK 300 3D Printer - Machine Diagram 1CreatBot PEEK 300 3D Printer - Machine Diagram 2

Printer Operation

CreatBot PEEK 300 3D Printer - Printer

  1. Turn on printer.
  2. Click “Move” > “All home” on the screen.
  3. Move the extruder by hand to 4 corners of bed, and check the distance between nozzle and bed. Tighten or loosen 4 adjusting nuts below the bed to make sure the distance between nozzle and bed is around 0.1mm with feeler blade or approximately the thickness of one business card in all corners to ensure the bed is Leveled.

Printer Operation

CreatBot PEEK 300 3D Printer - Printer 1

  1. Preheat nozzle.
  2. Straighted filament and check the filament do not self-winding.
  3. Thread the filament through the filament sensor and manually load the filament until it into the extruder.
  4. Click “Load”, until the filament come out from the nozzle.
  5. Click “Done”.

CreatBot PEEK 300 3D Printer - Printer 2

  1. Enter “ Filament” menu, click “Unload” .
  2. Wait for the nozzle heated to the suitable temperature.
  3. After reaching temperature, extruder will extrude a little filament, then unload the filament from extruder.
  4. Pull the filament out of the tube.

Main Menu
Touch screen

CreatBot PEEK 300 3D Printer - Touch screen

CreatBot PEEK 300 3D Printer - Symbol Touch and set up the temp of the nozzle.
210°C Preset nozzle temperature
25°C Current nozzle temperature
CreatBot PEEK 300 3D Printer - Symbol 1 Touch and set up the temp of the hotbed
.110°C Current platform temperature
45°C Preset platform temperature
CreatBot PEEK 300 3D Printer - Symbol 2 Touch and set up the temp of the Chamber.
70°C Current Chamber temperature
25°C   Preset Chamber temperature

Main Menu
Touch screen

CreatBot PEEK 300 3D Printer - Touch screen 1Detail page

CreatBot PEEK 300 3D Printer - Touch screen 2

Axis operation

CreatBot PEEK 300 3D Printer - Touch screen 3Filament menu

CreatBot PEEK 300 3D Printer - Filament SD Card/U-disk

CreatBot PEEK 300 3D Printer - SD

Info. page

CreatBot PEEK 300 3D Printer - pageSetting menu

CreatBot PEEK 300 3D Printer - Setting menu

The values in the picture are not real values, the real values refer to the printer default values
Setting menu

CreatBot PEEK 300 3D Printer - Setting menu 1

sink fan speed (range:1-100)
cooling fan speed (range:1-100)

CreatBot PEEK 300 3D Printer - Setting menu 2head temperature (range:0-420)
hotbed temperature (range:0-100)
Setting menu

CreatBot PEEK 300 3D Printer - Setting menu 3

Enter the WiFi name and password, and click Connect. The printer will automatically connect to WiFi.
Only supports 2.4GHz Wi-Fi.

Frequently Asked Questions

Hardware Troubleshoot

The environment is too low, or temperature sensor is damaged, please keep the room temperature above 0℃ .

Temperature of nozzle or bed too high, or temperature sensor is damaged, please keep their temperature in a suitable range.

3. USB connection problems ?

Please specify the correct port and baud rate (250000), or change a shorter USB cable.

4. Nozzle heats up too slowly ?

Temperature in door is too low, or use a fan duct, or turn up output voltage (24.5v).

5. Print head stuck ?

Clean the guide rail and add lubricating oil.

6. Print head can not move ?

Stepper motor chipset burned, or belt damaged, or belt wheel screw loose.

7. Print head hit the framework ?

Corresponding axis stop limit or circuit fault.

8. Unable to power on ?

Power switch is damaged or fuse is burned, and please check whether the power adapter is working properly or power check board is damaged.

Printing Troubleshoot

1. How to set the temperature of the nozzle ?

Different filament temperature is different, general as follows: PLA temperature 190℃~210℃,bed 45-60℃ . ABS temperature 230℃~250℃,bed 80-100 ℃ . You must leave enough time for filament heating, so the faster printing speed need the higher temperature, 60mm/s temperature need raise about 10℃. In the same way, larger thickness need higher temperature.

2. How to set the temperature of the hot bed ?

The main purpose of the hot bed is to prevent model wrapped, PLA need about 45℃ and 70℃ for ABS is enough, but due to the environment and filament, we often need to increase the temperature, the highest temperature not over 120℃, and you can close the bed above 100mm except printing ABS or other high-temperature required filaments.

3. The model not stick on the platform ?

Please paste masking paper or Kapton tape on the platform, or the nozzle is too far away from the platform, or the bottom of the model is not flat.

4. No or less silk coming on the first layer ?

The distance between nozzle and platform is too small, or the filament has not been sent to the nozzle.

5. Why nozzle is not spit silk ?

The filament is not pressed or too tight, or print temperature is too low, or the filament feeder not working.

6. How to prevent model become warped ?

Increase hot bed temperature or use Kapton, or change platform adhesion type to Raft, or cover the baffle, or reduce indoor ventilation.

7. How far from nozzle to platform appropriate ?

Distance should be 0 in theory, but there is no absolutely flat platform, so the distance should +-0.1mm. Finally, with the actual printing effect as the standard, too close will lead to a silk blocked, too far will cause the model not stick on the platform.

8. How to determine whether the temperature is too high ?

PLA temperature is too high will appear liquefaction, ABS will be the carbide, that will block the nozzle.

9. What reasons will causing nozzle blocked ?

Filament are impurities or print environment dust too much, bad of thermal conductivity between the nozzle and the heating block.

10. Model surface is loose with crack ?

The layer is too high or the printing speed too fast, nozzle temperature too low or filament press nut too loose, or filament is wrapped.

11. How to print a small model ?

Multiple the model, and print them at a time.

12. Dual color model not aligned ?

Adjust offset of second nozzle in machine settings.

13. Dual color model color interference ?

Align two nozzle in vertical direction

14. There is too much silk drag on the model ?

Please enable filament retraction, and specified proper retract speed, and distance, the retract distance should not less than 4mm, and the speed not less than 10mm/s.

Henan Creatbot Technology Limited
Website: www.CreatBot.com
Email: sales@creatbot.com
Address: No.150 Lamei Road,
Zhongyuan District,
Zhengzhou City, Henan Province, China

Documents / Resources

PDF thumbnailPEEK-300 3D Printer
User Manual · PEEK-300, PEEK-250, PEEK-300 3D Printer, PEEK-300, 3D Printer, Printer

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.