Yaber E1 Projector User Manual

E1 Projector

Specifications:

  • Model Number: E1
  • Auto Focus
  • Electronic Keystone Correction
  • Source Selection
  • Connectivity: WIFI, BT
  • Screen Mirroring: Android, IOS

Product Usage Instructions:

Connect To WIFI:

  1. Turn on the projector and ensure it is connected to WIFI.
  2. On the Home Page, select Settings.
  3. Select Network Settings and enter the WIFI password.
  4. Click Connect to establish the connection.

Auto Focus:

  1. Select Projection Image Settings on the main page.
  2. Enable Auto Focus to enter auto focus mode.
  3. If the image is still unclear, use F+/F- for electronic focus
    adjustment.

Electronic Keystone Correction:

  1. Select Advanced Keystone after selecting Projection
    Settings.
  2. Adjust the four corners using arrow keys until the picture is
    corrected.

BT Settings:

  1. Select BT Setting on the main page.
  2. In Manual Setting, match with the correct BT device.

Screen Mirroring for Android Phone:

  1. Ensure projector and Android phone are connected to the same
    WIFI.
  2. On the Home Page, select Android Cast and follow on-screen
    instructions.

Screen Mirroring for IOS System:

  1. Make sure projector and IOS device are on the same WIFI
    network.
  2. Select IOS WiFiCast on the main page.
  3. Connect the lightning connector to the phone and
    projector.
  4. Trust the connection on your phone to share the screen with the
    projector.

FAQ:

1. How do I troubleshoot connectivity issues?

Ensure both devices are connected to the same WIFI network and
check for any password discrepancies.

2. What should I do if the image is still unclear after auto
focus?

Use the electronic focus adjustment buttons (F+/F-) for further
image clarity.

Loading PDF…
Download PDF

PROJECTOR Model Number: E1

Auto Focus Electronic Keystone Correction
Source Selection

Operating Instructions
Connect To WIFI

Auto Focus

Electronic Keystone Correction

BT Settings

Screen Mirroring for Android Phone

Screen Mirroring For IOS System

ios Cable Cast

Source Selection

1.43

1.96

2.78

1. Select “Settings” on Home Page

1. Select “Settings” on Home Page

1. Select “Settings” on Home Page

1. On Home Page, select

1. Click “IOS WiFiCast” on the main page, make

1. Connect the lightning connector to the phone.connect the

3.32

1. Select “Settings” on Home Page

“Android Cast”

sure the projector and IOS devices connect with same WIFI

other end to the projector

Selec SOURCE n the main page to enter the signal source interface

2. Click “Trust” the window that pops up on the phone.

Auto focus

Auto trapezoid displace

3. Enter device password.

2. Select “Network Settings”

ManuaI focus Screen zoom
2. Select “Projection Image Settings” and place “Auto Focus” in the “On” state. The projector will enter auto focus mode. After completing auto focus but the image is still unclear, you can press “F+/F_” for electronic focus to make the image clear.

2.Select “Advanced Keystone” after selecting “Projection Settings”

2. Select “BT Setting”

Select Device
E1 Recently connected

Android & ios Cast

Cancel

View Help

&Focusing camera

3. Turn on the “WIFI “and make i onnected

4. Enter the password and click ” Connect”

a 3. this is the picture when the projectors is doing Auto focus.

3. Use the arrow keys to adjust the four corners until the picture is corrected

3. Make ” BT ” in ” Manual Setting ” and try to match with the correct BT device.

2. Select “Screen Mirroring”or”
Smart Mirroring” on your phone (Note:different phones have different name).

3. Choose “E1” to share screen with projector.

2. Find “Screen Mirroring” on your IOS devices to share the screen with projector.

1. Make sure that the projector and mobile phone are connected to the same WIFI, enter the main page and select “Android Cast” and follow the steps on the screen.

FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Documents / Resources

PDF thumbnailE1 Projector
User Manual · E1 Projector, E1, Projector

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.