8BitDo Ultimate 3 Controller For XBOX

Overview
Ultimate 3 XBOX is a multi-mode controller that supports wired USB, 2.4G wireless, and Bluetooth pairing. Use the XBOX button to power on/off, configure volume and special modes, connect via the appropriate connection method, and calibrate joysticks/triggers when needed.
Specifications
| Battery | Built-in 1000 mAh battery pack |
|---|---|
| Wireless usage time | Up to 22 hours (2.4G) |
| Bluetooth usage time | Up to 32 hours (Bluetooth) |
| Charging time | About 4 hours |
| Auto power-off | Shuts down if it fails to connect within 1 minute of startup, or if there are no operations within 15 minutes after a successful connection |
| Auto power-off exception | Does not shut down during wired connection; also not automatically powered off when connected to 3.5 mm headphones for audio playback |
| Audio jack | 3.5 mm audio jack (not supported over Bluetooth) |
| Wireless modes | 2.4G (via included 2.4G adapter/dock use) and Bluetooth |
| System requirements (Windows) | Windows 10 (1903) or above; ensure the Xbox console is updated to the latest system version |
| System requirements (Apple/Android) | Android 13.0 or above |
Quick Setup & Use
- Power on/off: Press the XBOX button to turn on. Press and hold the XBOX button for 6 seconds to turn off. Press and hold for 12 seconds to force the controller off.
- Enable/disable 1000Hz Tournament Mode (Windows only): When connected via wired or wireless mode, press and hold View + Menu for about 3 seconds.
- Wireless (2.4G): Connect the dock to your Xbox console or Windows PC via USB cable. Set the controller Mode switch to 2.4G. Press the XBOX button; wait until the Status LED stays solid.
- Wired: Connect the controller to your Xbox console or Windows device via USB. Press the XBOX button; wait until the Status LED stays solid.
- Bluetooth (Apple/Android): Set the Mode switch to BT. Press the XBOX button. For first-time pairing, press and hold the Pair button for 3 seconds until the Status LED blinks rapidly, then pair on the phone/tablet’s Bluetooth settings. Status LED stays solid when connected.
- Volume adjustment: Use the provided button combination to adjust headset volume and audio balance (a tone indicates max/min; vibration indicates the midpoint/default).
Product Description
- Press the XBOX button to turn on the controller.
- Press and hold the XBOX button for 6 seconds to turn off the controller.
- Press and hold the XBOX button for 12 seconds to force the controller off.
- When connected via wired or wireless mode, press and hold the View + Menu buttons for about 3 seconds to enable/disable the 1000Hz Tournament Mode.(Windows only; trigger vibration will be disabled.)

- LB
- LS
- Force Ring
- Square button
- D-pad
- View button
- XBOX button / Status LED
- Menu button
- Profile LED
- Profile button
- Share button
- RB
- Star button
- RS
- Force Ring
- RT
- Trigger stops
- PR
- R4
- Power LED
- Pair button
- L4
- 3.5mm audio jack
- Mode switch
- LT
- Trigger stops
- PL
- 2.4G adapter
Force Ring(Joystick Tension Adjustment)

XBOX Series, XBOX One, and Windows 10/11
- System Requirement: ensure your XBOX console is updated to the latest system version.
- System Requirement: Windows 10 (1903) or above.
Wireless Connection
- Connect the dock to your XBOX console or Windows PC via a USB cable. (No need to remove the 2.4G adapter.)
- Turn the controller Mode switch to 2.4G position.
- Press the XBOX button to turn on the controller and wait till the controller is recognized by the device, the Status LED will stay solid when the connection is successful.
Wired Connection
- Connect the controller to your XBOX console or Windows device via a USB cable.
- Press the XBOX button to turn on the controller and wait till the controller is recognized by the console, the Status LED will stay solid when the connection is successful.]
Apple® / Android
- System requirement: Android 13.0 or above.
- For the latest compatibility information regarding Apple device system versions, please refer to: https://www.8bitdo.com/apple/
Apple®, iPadOS®, macOS®, tvOS®, and visionOS® are the trademarks of Apple Inc., registered in the U.S. and other countries.
Bluetooth Connection
- Turn the controller Mode switch to BT position.
- Press the XBOX button to turn on the controller.
- Press and hold the Pair button for 3 seconds to enter the pairing mode, the Status LED will blink rapidly. (This is required for the very first time only)
- Go to your Apple or Android device’s Bluetooth Setting and pair with “Ultimate 3 Controller”, the Status LED will remain solid to indicate a successful connection.
Volume Adjustment
- Use the button combination to adjust the headset volume and audio balance. A tone will indicate when the maximum or minimum level is reached, and a vibration will notify you when set to the midpoint (default).
- 3.5mm headphones are not supported while using Bluetooth connection.

L4/R4/PL/PR Buttons Configuration
- Single button on the controller can be mapped to the L4/R4/PL/PR buttons.
- Share button and XBOX button are not supported for the button configuration.

Battery

- Built-in 1000mAh battery pack, 22 hours of usage time via wireless 2.4G connection, 32 hours of usage time via Bluetooth connection, rechargeable with 4 hours charging time.
- The controller will automatically shut down if it fails to connect within 1 minute of startup, or if there are no operations within 15 minutes after establishing a connection.
- The controller will not shut down during wired connection.
- The controller will not automatically power off when connected to 3.5mm headphones for audio playback.
- Charging time and battery life depend on variations in settings or environmental factors, and actual results may vary.
Calibrate Joysticks and Triggers
Please follow the steps below:
- Controller in the powered-on state, press and hold the “LB+RB+View+Menu” buttons for 8 seconds to enter calibration mode, the Status LED will start to blink.
- Push the joysticks to the edge and rotate them slowly 2–3 times.
- Slowly press the triggers to the bottom 2–3 times.
- Press the same “LB+RB+View+Menu” buttons combination again to complete the calibration.
Re-pair the Controller and Adapter
If the connection is lost or the adapter needs to be re-paired, you can follow the steps below to re-pair the controller with the adapter:
- Connect the dock to your XBOX console or Windows PC via a USB cable. (No need to remove the 2.4G adapter.)
- Turn the controller Mode switch to 2.4G position.
- Press the XBOX button to turn on the controller.
- Press and hold the Pair button for 3 seconds to enter the pairing mode, the Status LED will blink rapidly.
- Both the Status LEDs on the controller and adapter will become solid when the connection is successful.
Safety Warnings
- Please always use batteries, chargers, and accessories provided by the manufacturer.
- The manufacturer is not liable for any safety issues arising from the use of non-manufacturer-approved accessories.
- Do not attempt to disassemble, modify, or repair the device yourself. Unauthorized actions may result in serious injury.
- Avoid crushing, disassembling, puncturing, or attempting to modify the device or its battery, as these actions can be dangerous.
- Any unauthorized changes or modifications to the device will void the manufacturer’s warranty.
- This product contains small parts that may cause choking. Not suitable for children under three years old.
- This product features flashing lights. Individuals with epilepsy or photosensitivity should disable the lighting effects before use.
- Cables may cause tripping or entanglement hazards. Keep them away from walkways, children, and pets.
- Stop using this product immediately and seek medical attention if you experience dizziness, visual disturbances, or muscle spasms.
Ultimate Software
Please visit Microsoft Store to download and use Ultimate Software X for XBOX/Windows platforms.
Support
Please visit support.8bitdo.com for further information and additional support.
Troubleshooting
- Status LED behavior / successful connection: For 2.4G or wired connection, wait until the Status LED stays solid—this indicates the connection is successful.
- If the controller is not connecting: Note the controller will automatically shut down if it fails to connect within 1 minute after startup. Try the appropriate connection steps again (2.4G via dock/USB, wired via USB, or Bluetooth pairing mode).
- Re-pair controller with the adapter (2.4G) when connection is lost: Connect the dock via USB, set Mode to 2.4G, power on, then press and hold the Pair button for 3 seconds. Enter pairing mode until the Status LED blinks rapidly; when both controller and adapter Status LEDs become solid, the connection is successful.
- Calibration issues: Recalibrate joysticks and triggers by powering on and holding LB + RB + View + Menu for 8 seconds (Status LED starts blinking), then move joysticks to edges and rotate slowly the indicated number of times, press triggers to the bottom the indicated number of times, and press LB + RB + View + Menu again to complete.
- Bluetooth audio limitation: 3.5 mm headphones are not supported during Bluetooth connection.
Documents / Resources
![]() | Ultimate 3 Controller For XBOX |
References
- support.8bitdo.cnsupport.8bitdo.cn
- support.8bitdo.comsupport.8bitdo.com
- 8bitdo.cn/apple/www.8bitdo.cn
- 8bitdo.com/apple/www.8bitdo.com
- 8bitdo.com/apple/을�참고해�주십시오www.8bitdo.com
- User Manualmanual.tools
Published: October 2, 2026
