8BitDO 24GULT2C Ultimate 2C Wireless Controller Instruction Manual

Product Instruction

• Press home button to turn on the controller.
• Hold home button for 3 seconds to turn off the controller.
• Hold home button for 8 seconds to force the controller off.

Windows 

• Required system: Windows 10(1903) or above.

Wireless Connection

1. Turn the mode switch to 2.4G.
2. Connect the 2.40 adapter to the USB port of your Windows device.
3. Press the Home button to turn on the controller, and the Status LED will remain solid to indicate a successful connection.

Wired Connection

Connect the controller to your Windows device via a USB cable, wait till the controller is successfully recognized by your Windows device, and the Status LED will remain solid to indicate a successful connection.

Android 

1. Required system: Android 9.0 or above.

Bluetooth Connection

1. Turn the mode switch to BT, then press the Home button to turn on the controller.
2. Hold the Pair button for 3 seconds to enter its pairing mode, the Status LED will start to blink rapidly (This is required for the very first time only).
3. Go to your Android device’s Bluetooth settings and turn it on, pair with [8BitDo Ultimate 2C Wireless], the Status LED will remain solid to indicate a successful connection.

Turbo Function

• D-pad, View, Menu, Home buttons are not supported.
• The turbo settings will not be saved permanently and will revert to default settings after the controller is powered off or disconnected.

Turbo Mode

Turn on: Hold the button you would like to assign the turbo functionality, then press the Star button to enable the Turbo Mode, the Mapping indicator will blink rapidly.
Turn off: Hold the button you would like to deactivate the turbo functionality, then press the Star button to disable the Turbo Mode, the Mapping indicator will turn off.

Auto Turbo Mode

Turn on: Hold the button you would like to assign the turbo functionality, then press the Star button twice to enable the Turbo Mode, the Mapping indicator will blink rapidly.
Turn off: Hold the button you would like to deactivate the turbo functionality, then press the Star button to disable the Turbo Mode, the Mapping indicator will turn off.

L4/R4 Configuration

• The Mapping indicator will blink continuously when the configured button is pressed.
  Hold the L4 / R4 button + the button you would like to configure, then press the Mapping button to complete the configuration. Repeat the same procedure to cancel the configuration.

Battery

• 32 hours of playtime via Bluetooth and 19 hours via wireless 2.4G connection, with a 480mAh built-in battery pack, rechargeable with 2 hour charging time.

status –  Low battery mode
LED indicator –  Red LED blinks
Battery charging –  Red LED stays solid
Battery fully charged – Red LED turns off

• The controller will automatically shut down if it fails to connect within 1 minute of startup, or if there are no operations within 15 minutes after establishing a connection.
• The controller will not shut down during wired connection.

Re-pair the Controller and Adapter

If the connection is lost or the adapter needs to be re-paired, you can follow the steps below to re-pair the controller with the adapter:

• Turn the mode switch to PC/2.4G position.
• Press the Home button to turn on the controller.
• Hold the Pairing button for 3 seconds to enter the pairing mode, the LED indicator will blink rapidly.
• Connect the 2.4G adapter to your Windows device.
• Both LED indicators on the controller and receiver will become solid when the connection is successful.

Firmware Update

Please visit support.8bitdo.com to access the Ultimate Software V2.

Support

Please visit support.8bitdo.com for further information & additional support.

Documents / Resources

8BitDO 24GULT2C Ultimate 2C Wireless Controller [pdf] Instruction Manual 24GULT2C, 2AOWF-24GULT2C, 2AOWF24GULT2C, 24GULT2C Ultimate 2C Wireless Controller, Ultimate 2C Wireless Controller, Wireless Controller, Controller

References

• User Manual