Markem-Imaje 9750 Industrial Inkjet Printer

Introduction

This manual comprises a text section and an illustrated section. The illustrated section is found at the end of the text section. Keep this information handy for future reference.

Important Note

Find all of your product's documentation on the Markem-Imaje website by scanning the QR code on the cover or by visiting www.markem-imaje.com.

Safety

This equipment is designed for industrial use and is intended for installation in areas where only adults are normally present.

Before using this printer, please read and fully comply with these instructions, the material safety data sheet (SDS) for consumables used, and the safety labels affixed to the printer.

Servicing must be performed only by knowledgeable or qualified personnel who are appropriately trained.

WARNING

Risk of puncture: When replacing cartridges, do not touch the nozzle.

Liability

Markem-Imaje shall not be liable for any damage or injury resulting from failure to follow these safety instructions, good manufacturing practices, and industry-wide safety standards when installing, using, or servicing Markem-Imaje equipment. Any user who modifies or repairs Markem-Imaje equipment, or uses consumables, spare parts, or accessories not supplied by Markem-Imaje, or fails to comply with Markem-Imaje specifications, assumes sole responsibility for the consequences.

Markem-Imaje is not liable for malfunctions or damage caused by equipment modification or use for purposes other than intended. The user is solely responsible for taking necessary precautions for their intended use of Markem-Imaje equipment.

Markem-Imaje consumables (inks, cleaning products, etc.), spare parts, and accessories are designed for use with Markem-Imaje equipment. Using non-Markem-Imaje consumables, spare parts, or accessories may harm the equipment and cause performance failures. Such use may also be inconsistent with testing conditions and affect compliance with certain standards. The user bears all risks associated with the use of unsuitable consumables and spare parts.

This equipment is certified in accordance with CE marking requirements.

Health / Hygiene / Environment

For certain consumables:

• Wearing contact lenses when handling these consumables is strictly prohibited.
• Ink-resistant gloves and safety goggles are recommended during cleaning operations.

Technical Specifications (9710-9750)

• Max. noise level: < 70 dbA
• Operating temperature: +5°C to +50°C (+41°F to +122°F)
• Humidity: 0-90% RH with no condensation

Certain inks may limit the temperature and humidity ranges (refer to the ink specification sheet). The printer must not be used in explosive atmospheres.

Fire Prevention

CAUTION: For continued protection against possible fire, use only the ink/additive mixtures specified by Markem-Imaje.

• If your printer uses flammable ink or additive: Never leave containers with ink, additive, or cleaning products, or ink-soaked rags (even dry) near the printer.
• Install a foam, CO2, or powder extinguisher immediately adjacent to the printer (maximum 10 meters).
• Never smoke near the printer. Affix a sign “NO SMOKING, FLAMMABLE INK” nearby.
• Ensure the printer is kept particularly clean, as dried ink deposits remain highly flammable.
• Drums of ink, additive, and cleaning solution must be closed and stored in a ventilated room, at the indicated temperatures, away from any source of heat, flame, or sparks.

Handling

When a printer contains consumables, it may only be moved in a vertical position over a short distance (e.g., within a workshop). Completely drain the printer before moving it in a position other than vertical, or if it is to be transported for a longer distance (e.g., in a vehicle).

Printer weight (9710-9750): 25 Kg (55.1 lbs) (without options or ink). Due to the system's weight, several people are required to handle it.

Installation

Installation work must be performed by Markem-Imaje technicians. Any modification to the installation is the responsibility of the installer.

The print head must be secured firmly in place with fastening devices.

The printer must be installed in a ventilated location, away from any source of heat, flames, or sparks.

The printer installation on the production line must not pose risks to staff. The console must not be integrated into a moving system. The operator's workstation should face the printer.

The printer must be connected to a single-phase mains electricity network with TT or TN type earth ground, using the supplied cable. The mains electricity connection via the mains plug must be easily accessible. Electrical and pneumatic installations upstream of the printer must comply with applicable regulations.

Printer electrical characteristics: refer to the manufacturer's plate on the printer, adjacent to the power socket.

When the printer or a part of it is attached to a stand, the stand must be connected to earth ground.

Earth ground all conducting parts not at a voltage reference and which are related to or close to the printer (metal frames, protective guards, etc.).

For information on fastening a Markem-Imaje accessory, refer to the assembly instructions delivered with it.

The printer must be placed on a perfectly horizontal and unimpeded surface (the underside of the printer must not be obstructed). The bottom of the console must be between 0.7 m and 1 m above floor level. The print head must be between -2 m and +2 m from the bottom of the console.

Types of Installation

1. Wall-mounted: The fasteners (anchors + bolts) must withstand a weight of at least 35 kg. Fixing by 4 screws of diameter 6 mm (0.24 in).
2. Tabletop: This table is designed for use with Markem-Imaje Industries inkjet printers only. Use with other equipment may cause instability, resulting in injury.
3. On base (Markem-Imaje): Stabilizer weights (x 2) are mandatory. They can be mounted above.

Servicing

Maintenance work should be carried out only by staff trained by Markem-Imaje and equipped with appropriate personal protective equipment (safety shoes, glasses, gloves, etc.). Any maintenance work not described in this manual must be carried out by Markem-Imaje technicians.

The printer must always be disconnected from the mains by the mains plug before any operations requiring it to be switched off. Use appropriate tools for any work on electrical and hydraulic circuits.

When working on the ink circuit, immediately wipe off any spillage and visually check for leaks. After each maintenance operation, empty and clean used waste receptacles. Do not leave rags soaked with consumables near the printer.

This unit contains a non-replaceable internal lithium-ion battery. The battery may burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not crush, puncture, or dispose of the battery in fire or water.

Recycling

Disposal of used batteries and rechargeable batteries: Applicable in European Union countries and other European countries with selective waste collection systems.

Disposal of used electrical and electronic equipment: Applicable in European Union countries and other European countries with selective waste collection systems.

These symbols indicate that the electrical and electronic device, and the batteries and rechargeable batteries therein, must not be disposed of as ordinary municipal solid waste. By ensuring appropriate disposal, you play an active role in avoiding harmful consequences to the environment and human health. Recycling of materials contributes to the preservation of natural resources.

Entrust your end-of-life electrical devices to a duly authorized disposal company for correct handling of all incorporated elements. For other cases, and to safely remove batteries, rechargeable batteries, and other materials, refer to the user manual or contact your Markem-Imaje representative.

Waste Consumables

Consumable waste must be managed in compliance with local regulations for waste management and dangerous goods transport. Transport, transit, and treatment of consumable waste must be handled by an entity with appropriate waste management licenses. Consumable waste must be treated in compliance with local regulations, either through recycling (e.g., distillation), incineration with energy recovery, or specific landfilling.

Radio

An RFID tag is fitted to each ink cartridge and contains the set-up information required by the printer. The printer reads the RFID tag during the calibration process and 'pairs' with the cartridge.

The RFID radio frequency is 13.56 MHz with a maximum power limit of 25 mW from the antenna.

FCC Rules

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC RF radiation exposure limits set forth for general population. This device must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

For Canada:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This device complies with ISED radiation exposure limits set forth for general population. This device must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Product Information

This product is for industrial use exclusively. For marking and coding equipment. Photographs and drawings are not contractual. The original document was written in French. Only the French text of this document is authentic and prevails in case of dispute. Markem-Imaje reserves the right to modify its product specifications without prior notice. Any reproduction, even partial, of this document is prohibited.

© 2021 Markem-Imaje. All rights reserved.