I-S866 LCD Instruments V1.0 Incwadi Yokusebenza

Izinsimbi ze-S866 LCD V1.0

Imanuwali Yokusebenza YamaShayina Yezinsimbi ze-S866 LCD V1.0

Abasebenzisi abahloniphekile, ngaphambi kokusebenzisa insimbi ye-LCD engu-S866, sicela ufunde le ncwajana ngokuningiliziwe.Incwajana izokukhombisa ukuthi uyisebenzise kahle yini insimbi ukubona imisebenzi ehlukahlukene yokulawulwa kwezimoto nokubonisa izimoto.

Umsebenzi nokubonisa

1. : Inkinobho yokusebenza UP ukhiye
2. : Inkinobho yokusebenza inkinobho ye-SW
3. :  Inkinobho yokusebenza kwenkinobho
4. km / h: Ijubane lokugibela lesikhathi sangempela (imethrikhi)
5. mph: Ijubane lokugibela lesikhathi sangempela (uhlelo lwaseBrithani)
6. : Uphawu lwe-Brake
7.  : Ukuthungatha inkinga (akusetshenziswanga)
8. : 5Section Electricity Inkomba
9. km : Ukuhamba ngamamayela (uhlelo lwemethrikhi)

Ukusebenza okusebenzayo

Vula bese ucisha
Cindezela isikhathi eside Ikhibhodi, ibhuth; cindezela isikhathi eside  Ukhiye, vala.Uma imoto iyeka ukushayela futhi ingasebenzisi ithuluzi imizuzu engu-10, insimbi izocisha ngokuzenzekelayo bese icisha ukunikezwa kwamandla kwemoto kagesi.
Isibonisi esibonisa 1

Cindezela isikhathi eside  Ikhibhodi, i-boot, faka isibonisi esibonakalayo esisodwa.

 

 

Khanyisa amalambu

Cindezela isikhathi eside Ikhibhodi yekhibhodi, khanyisa amalambu wangemuva namalambu ezimoto; cindezela futhi  Ikhibhodi, cisha amalambu wangemuva namalambu emoto.

 

 

Usizo shift

Umshini omfishane or  Ukhiye, shintsha 1-5 files Izinga lamandla aphansi kakhulu ku-
Igiya eli-1 nezinga lamandla eliphansi kunawo wonke ngamagiya amahlanu
Amandla aphezulu.Igiya lokuqala libuyiselwa ngokuzenzakalela njalo lapho umshini uvuliwe. 0 igiya elingenamandla.

 

km / h ukukhuthaza imisebenzi

Bamba phansi  Ukhiye, Ukubonisa Indawo yeGear Izimoto zihamba ngesivinini esingeqi ku-6Km / h. Sicela ukhiye, ukuhoxiswa komsebenzi.

 

 

Indawo Ekhombisa Imisebenzi Eningi

Umshini omfishane  Ukhiye, ukushintshela ku view Imininingwane ye-ODO-TRIPVOL- IME-ODO.

 

 

 

3 Fault code ukubonisa

Izilungiselelo Zento Yemenyu

I-P01-P20 Incazelo Yesibonisi Semenyu Nencazelo Yokubaluleka

I-P01: Ukukhanya kwangemuva: izinga elimnyama kakhulu 1, izinga elikhanye kakhulu 3
I-P02: iyunithi yamamayela: 0: KM; 1: IMILE
P03: UmqtagIzinga le-e: I-24V, 36V, 48V, 60V
I-P04: Isikhathi sokulala: 0, hhayi ukulala; Ezinye izinombolo yilezi
izikhathi zokulala, ububanzi: 1-60; Imizuzu yeyunithi.
P05: Ukukhethwa kwenombolo ye-PAS: 0,3 file imodi mode 1,5 imodi yegiya:
P06: Ukuhlelwa kwesondo: iyunithi, intshi.
inani lobubanzi besondo: 5.0 ~ 50 Precision: 0.1 intshi Le parameter ihlobene nejubane lokubonisa imitha futhi idinga ukufakwa kahle;
I-P07: Inombolo yensimbi kazibuthe esheshayo: ububanzi: 1-100.
Le pharamitha ihlobene nesivinini sokubonisa imitha futhi idinga ukufakwa kahle. Uma kuyimoto ejwayelekile yehabhu, inani lensimbi kazibuthe lifakwa ngqo. Uma kuyimoto enejubane elikhulu, kuyadingeka futhi ukubala isilinganiso sokuncipha, nedatha yokufaka = inani le-magnetic steel × deceleration ratio. Ngaphambiliample: inani lamagnet motor 20, deceleration ratio 4.3: idatha yokufaka ithi: 86 = 20 × 4.3
P08: Ukusetha umkhawulo wejubane: Isivumelwano No. 2 ububanzi 0-100km / H, 100 asisho umkhawulo wejubane. Imininingwane yokufaka lapha imele isivinini esikhulu sokusebenza semoto: isibample, input 25, ekhombisa ukuthi isivinini sokusebenza semoto esiphezulu ngeke seqe ku-25km / h. Ijubane lokushayela ligcinwa ngenani elibekiwe, Iphutha: ± 1km / h; (Umkhawulo wejubane wamandla nokujika ulingana).

Qaphela: Inani lapha lisuselwa kumakhilomitha. Lapho ukusethwa kweyunithi kuguqulwa kusuka kumakhilomitha kuya kumamayela, inani lejubane lesibonisi esibonakalayo liguqukela ngokuzenzakalela kunani elilungile lemayela, kepha idatha yenani lomkhawulo wejubane elibekwe kule menyu ngaphansi kwesixhumi esibonakalayo semayela aliguqulwanga. Akuhambisani nomkhawulo wangempela wejubane wejubane lemayela.
I-P09: isiqalo se-zero, isilungiselelo sesiqalo esingezona zero: 0: zero ukuqala; 1: Isiqalo esingeyona zero.
I-P10: Imodi yedrayivu iyasethwa: 0: I-Power Drayivu (kungakanani amandla okukhishwayo okunqunywa ngamandla file bit, futhi inkinobho ayivumelekile ngalesi sikhathi).

1. Idrayivu kagesi (ngokuguqula isibambo sokushayela, amandla file bit ayisebenzi ngalesi sikhathi).
2. Ukuhlalisana Okuqhutshwa Amandla nogesi

P11: Isilungiselelo sokuzwela sosizo: ububanzi: 1-24
I-P12: Usizo lokuqala ukulungiselelwa kokuqina: ububanzi: 1-5
I-P13: Amandla Wokusetha Uhlobo Lwe-Disk lwensimbi: 5, 8, 12

Izinhlobo Zensimbi Magnetic
I-P14: Ibanga lokubeka inani lomkhawulo wesilawuli: 1-20A
I-P15: Isilawuli singagadlitage
I-P16: Isethingi enguziro ye-ODO: ubude cindezela ukhiye imizuzwana emi-5 ye-ODO zero
I-P17: Ukuhamba ngomkhumbi okuzenzakalelayo: 0: Akukho ukuhamba ngezimoto okuvumela, 1: ukuvumela ukuhamba ngezinyawo; (isebenza ku-protocol 2 kuphela)
P18: Khombisa ukulungiswa kwesilinganiso sejubane: ububanzi: 50% ~ 150%,
I-P19: Ukukhethwa kwe-Zero PAS: 0: 0 file, 1: ayifaki u-0 file
P20: 0: 2 Protocol 1: 5 S Protocol 2: Standby 3: Ema eceleni

Ukuguqulwa kokukhethwa kwepharamitha yenketho yemenyu

Ngemuva kokuthi insimbi ivuliwe, cindezela isikhathi eside ngasikhathi sinye ukhiye + Ukhiye kusixhumi esibonakalayo semenyu ye-P01, cindezela okufishane Izinkinobho zingashintshelwa kumenyu elandelayo; kwimenyu yamanje, Chofoza  Isamba sokhiye  Izinkinobho zingaguqula amapharamitha wemenyu yamanje; ngemuva kokuguqulwa, cindezela iDemo Izinkinobho zingashintshelwa kumenyu elandelayo Ngemuva kokuthi imingcele yemenyu iguquliwe, cindezela futhi ngasikhathi sinye  ukhiye + Ukhiye, Phuma kusixhumi esibonakalayo semenyu, buyela kusixhumi esibonakalayo esijwayelekile sesibonisi. Phakathi kwabo, inani lepharamitha yemenyu ye-P16 inani lamanje eliphelele lamanani, inani alikwazi ukuguqulwa, kepha lingasuswa.  Ikhibhodi yemizuzwana engu-5, imayela eliphelele lisuliwe.

Usayizi womzimba wensimbi nenkomba yezintambo

 

Imishini Yokusebenza ye-S866 LCD V1.0 - Landa [kuthuthukisiwe]
Imishini Yokusebenza ye-S866 LCD V1.0 - Thwebula