Zhongshan Chuangxi Electronic Technology CX-XK02 Music Starry Projector top

Zhongshan Chuangxi logoMusic Starry Projector

User Manual

Zhongshan Chuangxi Electronic Technology Music Starry Projector

Unboxing Chek
Thank you for purchasing our products, please read the instruction manual carefully before use. Instruction manual contains necessary safety advice and user instructions, follow the instruction manual to operate in order to avoid damaging the product for misuse.Check whether the product is damaged or not when you receive the product

Package list:
Music starry projector x 1
Remote controller x 1
USB cable x 1
User manual x 1

The power requirement of this product is USB DC 5V.Once the range exceeded,please use the regulator device,otherwise it ‘II affect its service life.


  1. Strictly in accordance with the instructions of this operation,do not disassemble the host and accessories.
  2. This product is suitable for indoor use.
  3. The product is projected by LED and laser combinations,please do riot use laser shone directly in eyes and keep away from children.

How to use

  1. Indoor use,projecting in the sky direction.
  2. How to use the light projector,as shown below.
  3. Connect Bluetooth “BTK10 “of the smart phone to play music.
  4. Use correct method of the remote control to make sure the remote control is pointing at the infrared sensor.

Zhongshan Chuangxi Electronic Technology Music Starry Projector A

Host button function description: (from left to right)

  1. Short press is laser + LED switch key (this button area is the infrared signal receiving place of remote controller).
  2. USB jack, projector can automatically identify songs inserted into USB memory and play music at the same time.
  3. Turn on/off the power supply
  4. USB data power cord socket (Note: the power adapter must use the specified voltage. Current 5V. 2A product)

This product has been comprehensive and rigorous tested at the factory,the user should strictly follow the warning and instructions Improper use resulting in product damage is not covered by the Company’s warranty.

Remote control function description

1 AUDIO ON/OFF: Press short to enter standby mode (low power consumption), and then press short to cancel standby mode (low power consumption).
2 MODE : Press short to switch Bluetooth, MUSIC mode (USB music playing mode)
3 MUTE: short press mute, unmute
4 pause/play, up and down music, volume addition and subtraction to the function of conventional music playing
5 Color Light ON/OFF: LED switch key, turn on the default blue light, brightness is the brightness of the previous adjustment, if the color is adjusted, turn off and then turn on to restore the original color, turn on the colored light to turn off the white light

Zhongshan Chuangxi Electronic Technology Music Starry Projector B

6 JUMP: short press to switch between the two color conversion modes.
7 LASER: Short press alternates from breathing mode to normally bright mode, long press turns off the laser lamp, and then short press enters normally bright mode after turning off the laser lamp.
8 SOUND FLASH: microphone key, colored light and laser all jump
9 according to mic detection energy, NightLight ON/OFF: short press switch white light. If you press the color light on/OFF key in this mode, the blue monochrome laser lamp breathing mode will be released. If you press the Jump key in cover mode to enter Jump mode directly, pressing other color mode keys will not work.
10 COLOR+: short press color adjustment (color cycle), blue → purple (blue+ red), → red → orange (red + green) → green → green → (green +blue)
11 COLOR-: short press color adjustment (color cycle), blue ← purple (blue+red)← red← Orange (red +green)← green ← green (green + blue)
12 MOTO STOP: short press motor control (speed cycle), initial default 60%-100%-off-40%-60%-100% cycle.
13 LUMINANCE-: short press brightness level minus, each press minus 10%, minimum to 10%
14 LUMINANCE +: short press brightness level plus, each press increase 10%, maximum to 100%
15 1H: short press turn on the automatic optical machine for 1 hour, long press (1 H or 3H or 5H) can turn off the timing shutdown
16 3H: short press turn on the automatic optical machine for 3 hours, long press (1H or 3H or 5H) can turn off the timing shutdown
17 5H: short press turn on the automatic optical machine for 5 hours, long press (1 H or 3H or 5H) can turn off the timing shutdown


The transparent spherical surface of this product belongs to vulnerable parts, please do not impact.


Maximum LED power:   2*4W
Green laser:                     < 1 mW
Power input:                    USB DC5V.2A
Operating temperature:   14F ~ 104F (-10°C ~ 40°C)
Projection Coverage:       161 ~ 538 ft² (15 ~ 50m² )
Product size:                   123*128mm

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement.

Documents / Resources

Zhongshan Chuangxi Electronic Technology CX-XK02 Music Starry Projector [pdf] User Manual
CX-XK02, CXXK02, 2A7NB-CX-XK02, 2A7NBCXXK02, CX-XK02 Music Starry Projector, CX-XK02, Music Starry Projector

Leave a comment

Your email address will not be published.