DEWENWILS 150W 低音量tage Landscape Lighting Transformer

一、簡介

Thank you for choosing the DEWENWILS 150W Low Voltage Landscape Lighting Transformer. This device is designed to convert standard 120VAC household current to a safe 12V or 15V AC output, suitable for various outdoor low-voltage lighting applications. Featuring a built-in photocell sensor and programmable timer, it offers flexible control options for your landscape lights, ensuring energy efficiency and convenience.

2. 重要安全訊息

Please read and understand all instructions before installing or operating this transformer. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• 安裝或維修前，請務必先斷開斷路器的電源。
• This transformer is designed for outdoor use and must be mounted in a location protected from direct water spray.
• 確保所有線路連接牢固且絕緣良好，以防止短路。
• Do not overload the transformer. Calculate the total wattage of your connected lights and ensure it does not exceed the transformer's maximum output (150W).
• 僅使用低音量tage landscape lighting cable of appropriate gauge for your total wattage and cable length, as specified in the wiring chart.

3. 包裝內容

確認包裹內所有物品齊全：

• DEWENWILS 150W 低音量tage 景觀變壓器
• Detachable Photocell Sensor
• 安裝孔模板
• 安裝螺絲和錨栓
• 使用說明書

4. 產品結束view

DEWENWILS 150W 低音量tage Landscape Transformer features a durable metal casing and an intuitive control panel for easy operation.

圖 4.1：正面 view DEWENWILS 150W 低音量tage 景觀變形器，圖中顯示了數位顯示器和控制按鈕。

控制面板功能：

Figure 4.2: The control panel with indicators for various operating modes and time display.

• 數字顯示： Shows current time and programming settings.
• 模式指示器： LEDs for Manual, Auto, Photo On/Timer Off, Timer On/Timer Off, and Test modes.
• 按鈕： MENU, UP (▲), DOWN (▼), OK for navigation and setting adjustments.
• Photocell Sensor Port: Located at the bottom, for connecting the external photocell sensor.
• 接線端子： Screw terminals for connecting low-voltage landscape lighting wires (Common, 12V, 15V).

5. 設定與安裝

5.1 安裝變壓器

The transformer should be mounted vertically on a sturdy surface, such as a wall or post, at least 1 foot (30 cm) above ground level. Use the provided mounting hole template to mark drill points.

Figure 5.1: Step 2 of installation, showing the transformer being mounted to a wall.

1. Place the mounting hole template on the desired surface and mark the two drill points.
2. Drill pilot holes at the marked locations. Insert the provided anchors if mounting into masonry.
3. Secure the transformer to the surface using the provided mounting screws. Ensure it is firmly attached.

5.2 Connecting Low Voltag電子佈線

Before connecting any wires, ensure the transformer is unplugged from the main power supply.

Figure 5.2: Step 1 of installation, showing wires being connected to the terminal blocks.

1. Strip approximately 1/2 inch (1.2 cm) of insulation from the ends of your low-voltag景觀照明電纜。
2. Connect one wire from your lighting circuit to a 'COM' (Common) terminal.
3. Connect the other wire from your lighting circuit to either a '12V' or '15V' terminal, depending on the voltage requirements of your lights and desired brightness. For longer cable runs or higher wattage, 15V may be preferred to compensate for voltag降。
4. Tighten the screw terminals securely to ensure good electrical contact.

Cable Selection Chart:

Refer to the following chart to select the appropriate cable gauge (AWG) based on total fixture wattage and cable length to prevent voltage drop and ensure optimal performance.

5.3 Connecting the Photocell Sensor

The detachable photocell sensor allows for automatic dusk-to-dawn operation. Plug the sensor cable into the dedicated port at the bottom of the transformer. Position the sensor in a location that receives natural light and is not obstructed by artificial light sources at night.

Figure 5.3: The photocell sensor automatically activates lighting at dusk and deactivates at dawn.

6. 操作說明

Once installed and wired, plug the transformer into a standard 120VAC outlet. The digital display will illuminate.

6.1 設置時鐘

1. Press the 'MENU' button until 'CLOCK' is displayed or the clock icon flashes.
2. Use the '▲' and '▼' buttons to adjust the hour, then press 'OK' to confirm.
3. 重複以上步驟設定分鐘數和上午/下午設定。

6.2 選擇操作模式

The transformer offers 5 operating modes. Press the 'MENU' button to cycle through the modes and use 'OK' to select or confirm settings.

• 手動開/關： Lights remain on or off until manually changed. Press 'OK' to toggle between ON and OFF.
• 自動開/關： Lights turn on at dusk and off at dawn, controlled by the photocell sensor.
• Photo On/Timer Off: Lights turn on at dusk (via photocell) and turn off after a set duration (e.g., 4, 6, 8 hours). Use '▲' and '▼' to set the duration.
• Timer On/Timer Off: Lights turn on and off at specific programmed times. Set ON time and OFF time using '▲' and '▼' buttons.
• 測試模式： Activates lights for a short period (e.g., 1 minute) to verify connections and functionality.

6.3 記憶功能

The transformer includes a memory function that retains your selected operating mode and settings even after a power outage, eliminating the need for frequent re-programming.

7、維護保養

• Periodically inspect the transformer casing for any signs of damage or corrosion.
• Ensure all wire connections are tight and free from debris.
• Keep the photocell sensor clean and free from obstructions to ensure accurate dusk-to-dawn operation.
• Clean the exterior of the transformer with a soft, damp 布。請勿使用磨蝕性清潔劑或溶劑。

8。 故障排除

9. 規格

• 品牌： 德溫威爾斯
• 型號： HCLT03H1
• 輸入音量tage: 120VAC
• 輸出量tage: 12V/15VAC
• 最大輸出功率： 150W
• 電源： 有線電動
• 安裝類型： 壁掛式
• 材料： Metal (Sun-resistant, corrosion-proof)
• 認證： UL 認證
• 包裝尺寸： 9.92 x 7.6 x 6.61 英寸
• 物品重量： 8.33 磅

10. 保固和支持

For warranty information, technical support, or assistance with your DEWENWILS 150W Low Voltage Landscape Lighting Transformer, please contact DEWENWILS customer service. Refer to the product packaging or the official DEWENWILS web聯繫方式的網站。