ZEVNI LOGO2 Inch Wide Black LED Mini Pendant 
Item Number: A04437
Instruction Manual

A04437 2 Inch Wide Black LED Mini Pendant

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    » Go to the main fuse, or circuit breaker, box in your home.
    Place the main power switch in the “OFF” position.
    » Place the wall switch in the “OFF” position.
  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides.
    Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 5W.
  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 1

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 2 ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 3 ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 4 ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 5 ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 6
Ladder Phillips head.flat blade screwdriver Electrical tape Pliers Wire cutter/Stripper

PARTS TYPE & QTY INCLUDING:

(A) Mounting plate (1)
(B) Green ground screw (1)
(E) Stud (2)
(F) Canopy (1)
(G) Lock nut (1)
(H) Cord (1)
(I) Screw (2)
(J) Fixture body (1)
(K) Curved pipe (1)
(L) Glass shade (1)
ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 7 ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 8

ACCESSORIES & QTY ENCLOSED:
(C) Plastic wire connector (3)
(D) Mounting screw (2)
(M) Screwdriver (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
    » Go to the main fuse, or circuit breaker, box in your home.
    Place the main power switch in the “OFF” position.
    » Place the wall switch in the “OFF” position.
  3. » 1) Screw glass shade (L) onto fixture body (J).
    2) Thread screws (I) into curved pipe (K) and fixture body (J) using screwdriver (M). Tighten till snug.
  4. Unscrew studs (E) from canopy (F) then remove mounting plate (A). ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 8
  5. To adjust the hanging height of the fixture:
    ● Press down and hold lock nuts (F) by hand;
    ● Pull or push cable (H) and steel wire (I) in and out of canopy (E) to increase or decrease the hanging height.ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 10
  6. Attach mounting plate (A) to the outlet box with mounting screws (D).ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 11
  7. Make wire connections
    Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
    Connect ground wires according to the below chartZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 12Connect wires according to the below chart
    Connect Black or Red Supply Wire to: Connect White Supply Wire to:
    Black White
    *Parallel cord ( round & smooth) *Parallel cord ( square & ridged )
    Clear,Brown,Gold or Black without tracer Clear,Brown,Gold or Black with tracer
    Insulated wire ( other than green) with copper conductor Insulated wire ( other than green ) with silver conductor

    *Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus.)ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 13Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and
    then carefully tuck all wires into the outlet box.

  8. Raise canopy (F) to the ceiling and secure canopy (F) in place by threading studs (E) into mounting plate (A) and canopy (F).ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 14
  9. If needed, refer to STEP 5 and adjust the hanging height of the fixture again.ZEVNI A04437 2 Inch Wide Black LED Mini Pendant - FIGURE 15
  10. Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non­abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

www.ihomeangel.com
Rhino MA3PR-FL KammaBar Pro Aluminium Roof Bar - icon2 +1 850 296 2377
Working hours : Mon ­ Fri 9:00 ­ 16:00 EST
email ICONhomecustomercare@outlook.com

Documents / Resources

ZEVNI A04437 2 Inch Wide Black LED Mini Pendant [pdf] Instruction Manual
A04437 2 Inch Wide Black LED Mini Pendant, A04437, 2 Inch Wide Black LED Mini Pendant, LED Mini Pendant

References

Leave a comment

Your email address will not be published. Required fields are marked *