Tecla X KNX Multifunction Capacitive Touch Switch
User Manual
Tecla X
PC-ABS Capacitive push button with 1/2/4/6/8 buttonsand custom icons
ZVITX1 / ZVITX2 / ZVITX4 / ZVITX6 / ZVITX8
Application Programme Version: [1.9]
User Manual Version: [1.9]_a
www.zennio.com
INTRODUCTION
1.1 TECLA X
Tecla X is a KNX multifunction capacitive touch switch from Zennio with proximity sensor, luminosity sensor and backlighted buttons.
They are offered at a reduced weight, with one, two, four, six or eight capacitive touch buttons (according to the user’s needs) with LED backlight to confirm the press of the buttons as well as showing states.
Tecla X is a fully customisable solution for the control of rooms where user control of air conditioning systems, lighting, blinds, scenes, etc. is required.
The versatility offered by the functionality of buttons is complemented by the two builtin analog/digital inputs, the internal temperature sensor and a thermostat function, as well as an elegant design with fully customisable backlit icons.
The most outstanding features of Tecla X are:
- Fully customisable backlit icons.
- 1 / 2 / 4 / 6 / 8 touch buttons, which can operate as individual or pair controls.
- Horizontally or vertically oriented configuration (only available for the twobutton, six-button and eight button models.
- Light indicator (LED) for every button.
- Buzzer for an audible acknowledgement of user actions (with the possibility of disabling it either by parameter or by object).
- Possibility of locking / unlocking the touch panel through binary orders or scenes.
- Welcome Back object (binary or scene) which is sent to the KNX bus when a pulsation is detected after a certain period (configurable) of inactivity.
- Built-in temperature sensor.
- Ambient luminosity sensor for brightness automatic adjustment.
- Proximity sensor for quick start.
- Thermostat function.
- Heartbeat or periodical “still-alive” notification.
1.2 INSTALLATION
Figure 1 shows the connection outline of Tecla X:
- KNX connector
- Fixing clips.
- Programming LED.
- Programming Button.
- Touch area.
- Proximity and Luminosity.
Tecla X is connected to the KNX bus through the built-in terminal (1). An external DC power supply is not needed.
A short press on the programming button (4) will make the device enter the programming mode. The programming LED (3) will then light in red. On the other hand, if this button is held while the device gets connected to the bus, the device will enter the
safe mode. In such case, the programming LED will blink in red colour.
For detailed information about the technical features of Tecla X, as well as on security and installation procedures, please refer to the device Datasheet, bundled within the device packaging and also available at www.zennio.com.
1.3 START-UP AND POWER LOSS
After download or device reset it is necessary to wait for about 2 minutes without performing any action in order to make it possible a proper calibration of:
Proximity sensor.
Luminosity sensor.
Button presses.
For a correct calibration of the proximity and brightness sensors it is recommended not to remain too close or place anything less than 50cm approximately and do not hit with direct light to the device during this time.
CONFIGURATION
After importing the corresponding database in ETS and adding the device into the topology of the project, the configuration process begins by entering the Parameters tab of the device.
2.1 GENERAL
This tab is subdivided into several further sections, which contain different general and function-related parameters, both general and advanced.
2.1.1 CONFIGURATION
In the “Configuration” tab, the general settings are displayed.
ETS PARAMETERISATION
The following parameters are shown:
Number of buttons [1 / 2 / 4 / 6 / 8]: The application program can be downloaded in all five versions of the device. If the correct option is not selected, the push buttons will not work.
Device Orientation [Vertical (Normal) / Horizontal (Rotated)] 1 : enables horizontal or vertical orientation to be assigned to the device, for easy identification of the push-buttons during configuration process (ETS will show a figure with the final distribution of the push-buttons). To prevent inconsistency in the configuration, please note the following criterium:
Buttons [Enabled]: read-only parameter to make it evident that the “Buttons” tab is always enabled in the tab tree on the left. See section 0 for details.
Inputs [Disabled / Enabled]: enables or disables the “Inputs” tab in the tree on the left, depending on whether the device will or will not be connected any external accessories. See section 2.3 for details.
Thermostat [Disabled / Enabled]: enables or disables the “Thermostat” tab in the tree on the left. See section 2.4 for details.
Heartbeat (Periodic Alive Notification) [Disabled / Enabled]: incorporates a one-bit object to the project (“[Heartbeat] Object to Send ‘1’”) that will be sent periodically with value “1” to notify that the device is still working (still alive). 
Note: the first sending after download or bus failure takes place with a delay of up to 255 seconds, to prevent bus overload. The following sendings follow the parameterised period.
Device Recovery Objects (Send 0 and 1) [Disabled / Enabled]: this parameter lets the integrator activate two new communication objects (“[Heartbeat] Device Recovery”), which will be sent to the KNX bus with values “0” and “1” whenever the device begins operation (for example, after a bus power failure). It is possible to parameterise a certain delay [0…255][s] to this sending.
Note: After download or bus failure, the sending takes place with a delay of up to 6,35 seconds plus the parameterised delay, to prevent bus overload.
Scene after download [Keep Saved Scenes / Configured by parameters]: Allows to assign the option to update scenes only on the first download of the device version or to delete the saved scenes after the download of the device version.
Internal Temperature Sensor [Disabled / Enabled]: enables or disables the “Temperature Sensor” tab in the tree on the left. See section 2.1.2 for details.
Sounds [Default / Custom]: sets whether the sound functions (button beeps, alarm and doorbell) should work according to the pre-defined configuration or to a user-defined configuration. See section 2.1.4 for details.
Ambient luminosity sensor [Disabled / Enabled]: enables setting the ambient luminosity sensor. When the sensor is enabled, a new tab for its configuration is shown. See section 2.1.5 for details.
Proximity Sensor [Disabled / Enabled]: enables the proximity sensor. This functionality permits “waking up” the device when detecting presence, see section 2.1.6.
Time to Consider Inactivity [1…30…255] [s/min/h]: allows setting a time after which, if no pulsation or proximity detection has occurred, the LEDs turn off (or acquire the brightness level configured, see section 2.1.3).
Advanced Configuration [Disabled / Enabled]: enables or disables the “Advanced” tab in the tree on the left. See section 2.1.7 for details.
2.1.2 TEMPERATURE SENSOR
The internal temperature probe can monitor the ambient temperature of the room, thus making the device capable of reporting it to the KNX bus and of triggering certain actions when the temperature reaches specific values.
Please refer to the specific manual “Temperature Probe” (available in the product section at the Zennio homepage, www.zennio.com) for detailed information about the functionality and the configuration of the related parameters.
2.1.3 BACKLIGHT
Capacitive touch switches are able to manage the brightness of the LED according to two operating modes: normal mode and night mode.
Please refer to the specific manual “Brightness” (available in the product section at the Zennio website, www.zennio.com) for detailed information about the functionality and the configuration of the related parameters.
Note: Please note that this device does not have the [General] Activity object mentioned in this manual.
2.1.4 SOUNDS
For detailed information about the functionality and the configuration of the related parameters, please refer to the specific manual “Capacitive Touch Switches” available in the Tecla X product section at the Zennio homepage, www.zennio.com.
2.1.5 AMBIENT LUMINOSITY SENSOR
Capacitive touch switches incorporate a luminosity sensor to receive and monitor ambient brightness measurement.
Please refer to the specific manual “Luminosity and Proximity Sensor” (available in the product section at the Zennio homepage, www.zennio.com) for detailed information about the functionality and the configuration of the related parameters.
2.1.6 PROXIMITY SENSOR
Please refer to the specific manual “Proximity and Luminosity Sensor” (available in the product section at the Zennio homepage, www.zennio.com) for detailed information about the functionality and the configuration of the related parameters.
2.1.7 ADVANCED CONFIGURATION
For detailed information about the functionality and the configuration of the related parameters, please refer to the specific manual “Capacitive Touch Switches” available in the Tecla X product section at the Zennio homepage, www.zennio.com.2.2 BUTTONS
For detailed information about the functionality and the configuration of the related parameters, please refer to the specific manual “Capacitive Touch Switches” available in the Tecla X product section at the Zennio homepage, www.zennio.com.
2.3 INPUTS
Tecla X incorporates two analog/digital inputs, each configurable as a: Binary Input, for the connection of a pushbutton or a switch/sensor. Temperature Probe, to connect a temperature from Zennio. Motion Detector, to connect a motion detector (suitable for the new motion detector model from Zennio).
2.3.1 BINARY INPUT
Please refer to the specific user manual “Binary Inputs”, available in the Tecla X product section, at the Zennio website (www.zennio.com).
2.3.2 TEMPERATURE PROBE
Please refer to the specific user manual “Temperature Probe”, available in the Tecla X product section, at the Zennio website (www.zennio.com).
2.3.3 MOTION DETECTOR
Please refer to the specific user manual “Motion Detector”, available in the Tecla X product section, at the Zennio website (www.zennio.com).
2.4 THERMOSTAT
Capacitive touch switches implement one Zennio thermostat which can be enabled and fully customised.
Please refer to the specific manual “Zennio Thermostat” (available in the product section at the Zennio website, www.zennio.com) for detailed information about the functionality and the configuration of the related parameters.
ANNEX I. COMMUNICATION OBJECTS
“Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have a particular meaning because of the specifications or restrictions from both the KNX standard and the application program itself.
| Number | Size | I/O | Flags | Data type (DPT) | Functional Range | Name | Function |
| 1 | 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Heartbeat] Object to Send ‘1’ | Sending of ‘1’ Periodically | |
| 2 | 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Heartbeat] Device Recovery | Send 0 | |
| 3 | 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Heartbeat] Device Recovery | Send 1 | |
| 4 | 1 Byte | I | C – W – – | DPT_SceneNumber | 0 – 63 | [General] Scene: Receive | 0 – 63 (Run Scene 1-64) |
| 5 | 1 Byte | C – – T – | DPT_SceneControl | 0-63; 128-191 | [General] Scene: Send | 0 – 63/128 – 191 (Run/Save Scene 1-64) | |
| 6 | 1 Bit | I | C – W – – | DPT_Enable | 0/1 | [General] Touch Locking | 0 = Unlock; 1 = Lock |
| 1 Bit | I | C – W – – | DPT_Enable | 0/1 | [General] Touch Locking | 0 = Lock; 1 = Unlock | |
| 7 | 1 Bit | C – – T – | DPT_Switch | 0/1 | [General] Welcome Back Object | Switch Object Sent on Wake Up | |
| 8 | 1 Bit | I | C – W – – | DPT_Enable | 0/1 | [General] Sounds – Disabling Button Sound | 0 = Disable Sound; 1 = Enable Sound |
| 1 Bit | I | C – W – – | DPT_Enable | 0/1 | [General] Sounds – Disabling Button Sound | 0 = Enable Sound; 1 = Disable Sound | |
| 9 | 1 Bit | I | C – W – – | DPT_Ack | 0/1 | [General] Sounds – Doorbell | 1 = Play a Doorbell Sound; 0 = Nothing |
| 1 Bit | I | C – W – – | DPT_Ack | 0/1 | [General] Sounds – Doorbell | 0 = Play a Doorbell Sound; 1 = Nothing | |
| 10 | 1 Bit | I | C – W –– | DPT_Alarm | 0/1 | [General] Sounds – Alarm | 1 = Play Alarm Intermittent Sounds; 0 = Stop Alarm Sounds |
| 1 Bit | I | C – W –– | DPT_Alarm | 0/1 | [General] Sounds – Alarm | 0 = Play Alarm Intermittent Sounds; 1 = Stop Alarm Sounds | |
| 11, 12, 13, 14, 15 | 1 Bit | I | C – W – – | DPT_Switch | 0/1 | [General] Welcome Back Object – Additional Condition | Additional Condition Object x |
| 16 | 1 Bit | I | C – W –– | DPT_Enable | 0/1 | [General] Proximity Sensor | 0 = Disable; 1 = Enable |
| 17 | 1 Bit | I | C – W –– | DPT_Start | 0/1 | [General] External Proximity Detection | 1 = Detection |
| 18 | 1 Bit | C – – T – | DPT_Start | 0/1 | [General] Proximity Detection | Send 1 when Proximity is Detected | |
| 19 | 1 Bit | C – – T – | DPT_Bool | 0/1 | [General] Luminosity (1-Bit) | 0 = Over Threshold; 1 = Under Threshold | |
| 1 Bit | C – – T – | DPT_Bool | 0/1 | [General] Luminosity (1-Bit) | 0 = Under Threshold; 1 = Over Threshold | ||
| 20 | 1 Byte | O | C R – – – | DPT_Scaling | 0% – 100% | [General] Luminosity (Percentage) | 0% … 100% |
| 21 | 2 Bytes | O | C R – – – | DPT_Value_Lux | [General] Luminosity (Lux) | 0 Lux … 670760 Lux | |
| 22 | 1 Bit | I | C – W – – | DPT_DayNight | 0/1 | [General] Backlight Mode | 0 = Night Mode; 1 = Normal Mode |
| 1 Bit | I | C – W –– | DPT_DayNight | 0/1 | [General] Backlight Mode | 0 = Normal Mode; 1 = Night Mode | |
| 23 | 1 Byte | I | C – W –– | DPT_Scaling | 0% – 100% | [General] Display – Brightness | 0% … 100% |
| 24 | 1 Byte | I | C – W – – | DPT_Scaling | 0% – 100% | [General] Display – Contrast | 0% … 100% |
| 25, 31, 37, 43, 49, 55, 61, 67, 73, 79 | 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Ix] Switch | Send Selected Value on Short Press |
| 1 Bit | I | C – W T – | DPT_Switch | 0/1 | [Btn][Ix] Hold & Release | Send Selected Values on Hold and Release Presses | |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Ix] Two Objects – Short Press | Send Selected Value on Short Press | |
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Btn][Ix] Light – On/Off | (Short Press) Switch Between On and Off | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Btn][Ix] Shutter – Stop/Step | (Short Press) 0 = Stop Shutter/Step Up; 1 = Stop Shutter/Step Down | ||
| 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Btn][Ix] Shutter – Stop | (End Pressing) Stop Shutter | ||
| 25, 31, 37, 43, 49 | 1 Bit | C – – T – | DPT_Switch | 0/1 | [Btn][Ix] Light – On | (Short Press) Send On | |
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Btn][Ix] Light – Off | (Short Press) Send Off | ||
| 25, 31, 37, 43, 49, 55, 61, 67, 73, 79 |
1 Bit | C – – T – | DPT_Step | 0/1 | [Btn][Ix] Shutter – Stop/Step | (Short Press) Stop Shutter/Step Up | |
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Btn][Ix] Shutter – Stop/Step | (Short Press) Stop Shutter/Step Down | ||
| 26, 32, 38, 44, 50, 56,
62, 68, 74, 80 |
4 Bit | I | C – W T– | DPT_Control_Dimming | 0x0 (Detener) 0x1(Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Btn][Ix] Light – Dimming | (Long Press) Switch Between Dimming Up and Down |
| 26, 32, 38, 44, 50 | 4 Bit | I | C – W T– | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Btn][Ix] Light – Dimming | (Long Press) Dimming Up |
| 4 Bit | I | C – W T– | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) |
[Btn][Ix] Light – Dimming | (Long Press) Dimming Down |
| 27, 33, 39, 45, 51, 57, 63, 69, 75, 81 | 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Ix] Shutter – Move | (Long Press) 0 = Up ; 1 = Down | |
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Ix] Shutter – Move | (Start Pressing) Switch Between Up and Down | ||
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Ix] Two Objects – Long Press | Send Selected Value on Long Press | |
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Ix] Shutter – Move | (Long Press) Up | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Ix] Shutter – Move | (Long Press) Down | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Ix] Shutter – Move | (Start Pressing) Up | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Ix] Shutter – Move | (Start Pressing) Down | ||
| 28, 34, 40, 46, 52, 58, 64, 70, 76, 82 | 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Ix] LED On/Off | 0 = Off; 1 = On |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Ix] LED On/Off | 0 = On; 1 = Off | |
| 29, 35, 41, 47, 53, 59, 65, 71, 77, 83 | 1 Byte | I | C – W T– | DPT_Scaling | 0% – 100% | [Btn][Ix] Scaling | Send Selected Percentage Value on Short Press |
| 1 Byte | I | C – W T
– |
DPT_Value_1_Ucount | 0 – 255 | [Btn][Ix] Counter – 1-Byte Unsigned | Send Selected Value on Short Press | |
| 1 Byte | I | C – W T– | DPT_Value_1_Count | -128 – 127 | [Btn][Ix] Counter – 1-Byte Signed | Send Selected Value on Short Press | |
| 2 Bytes | I | C – W T– | DPT_Value_2_Ucount | 0 – 65535 | [Btn][Ix] Counter – 2-Byte Unsigned | Send Selected Value on Short Press | |
| 2 Bytes | I | C – W T– | DPT_Value_2_Count | -32768 – 32767 | [Btn][Ix] Counter – 2-Byte Signed | Send Selected Value on Short Press | |
| 2 Bytes | I | C – W T– | 9.xxx | -671088,64 – 670433,28 | [Btn][Ix] Float | Send Selected Value on Short Press | |
| 1 Byte | I | C – W T– | DPT_Value_1_Ucount | 0 – 255 | [Btn][Ix] Two Objects – Short Press (1- Byte) | Send Selected 1-Byte Value on Short Press | |
| 1 Byte | I | C – W T– | DPT_Scaling | 0% – 100% | [Btn][Ix] Shutter – Position | 0 – 100 % | |
| 1 Byte | I | C – W T – | DPT_Scaling | 0% – 100% | [Btn][Ix] Light – Dimming (Status) | 0 – 100 % | |
| 1 Byte | I | C – W T– | DPT_Room_State | 0 – 2 | [Btn][Ix] Room State | 0 = Normal; 1 = Make-up Room; 2 = Do not Disturb | |
| 30, 36, 42, 48, 54, 60,
66, 72, 78, 84 |
1 Byte | I | C – W T – | DPT_Value_1_Ucount | 0 – 255 | [Btn][Ix] Two Objects – Long Press (1- Byte) | Send Selected 1-Byte Value on Long Press |
| 85, 91, 97, 103, 109 | 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Switch | Left = 0; Right = 1 |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Two Objects – Short Press | Left = 1; Right = 0 | |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Two Objects – Short Press | Left = 0; Right = 1 | |
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Btn][Px] Light – On/Off | (Short Press) Left = Off; Right = On |
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Btn][Px] Shutter – Stop/Step | (Short Press) Left = Stop/Step Down; Right = Stop/Step Up | ||
| 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Btn][Px] Shutter – Stop | (End Pressing) Left = Stop-Down; Right = Stop- Up | ||
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Switch | Left = 1; Right = 0 | |
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Btn][Px] Light – On/Off | (Short Press) Left = On; Right = Off | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Btn][Px] Shutter – Stop/Step | (Short Press) Left = Stop/Step Up; Right = Stop/Step Down | ||
| 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Btn][Px] Shutter – Stop | (End Pressing) Left = Stop-Up; Right = Stop- Down | ||
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Switch | Lower = 0; Upper = 1 | |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Switch | Lower = 1; Upper = 0 | |
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Btn][Px] Light – On/Off | (Short Press) Lower = Off; Upper = On | ||
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Btn][Px] Light – On/Off | (Short Press) Lower = On; Upper = Off | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Btn][Px] Shutter – Stop/Step | (Short Press) Lower = Stop/Step Down; Upper = Stop/Step Up | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Btn][Px] Shutter – Stop/Step | (Short Press) Lower = Stop/Step Up; Upper = Stop/Step Down | ||
| 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Btn][Px] Shutter – Stop | (End Pressing) Lower = Stop-Down; Upper = Stop-Up | ||
| 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Btn][Px] Shutter – Stop | (End Pressing) Lower = Stop-Up; Upper = Stop- Down | ||
| 1 Bit | I | C – W T – | DPT_Switch | 0/1 | [Btn][Px] Two Objects – Short Press | Lower = 0; Upper = 1 | |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Two Objects – Short Press | Lower = 1; Upper = 0 | |
| 86, 92, 98, 104, 110 | 4 Bit | I | C – W T– | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Btn][Px] Light – Dimming | (Long Press) Left = Darker; Right = Brighter |
| 4 Bit | I | C – W T– | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) …0xF (Subir 1%) |
[Btn][Px] Light – Dimming | (Long Press) Left = Brighter; Right = Darker |
| 4 Bit | I | C – W T– | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Btn][Px] Light – Dimming | (Long Press) Lower = Darker; Upper = Brighter | |
| 4 Bit | I | C – W T– | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Btn][Px] Light – Dimming | (Long Press) Lower = Brighter; Upper = Darker | |
|
87, 93, 99, 105, 111 |
1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Two Objects – Long Press | Left = 0; Right = 1 |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Two Objects – Long Press | Left = 1; Right = 0 | |
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Px] Shutter – Move | (Long Press) Left = Down; Right = Up | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Px] Shutter – Move | (Start Pressing) Left = Down; Right = Up | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Px] Shutter – Move | (Long Press) Left = Up; Right = Down | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Px] Shutter – Move | (Start Pressing) Left = Up; Right = Down | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Px] Shutter – Move | (Long Press) Lower = Down; Upper = Up | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Px] Shutter – Move | (Long Press) Lower = Up; Upper = Down | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Px] Shutter – Move | (Start Pressing) Lower = Down; Upper = Up | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Btn][Px] Shutter – Move | (Start Pressing) Lower = Up; Upper = Down | ||
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Two Objects – Long Press | Lower = 0; Upper = 1 | |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] Two Objects – Long Press | Lower = 1; Upper = 0 | |
| 88, 94, 100, 106, 112 | 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] LED On/Off | 0 = On; 1 = Off |
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Btn][Px] LED On/Off | 0 = Off; 1 = On | |
| 89, 95, 101, 107, 113 | 1 Byte | I | C – W T– | DPT_Scaling | 0% – 100% | [Btn][Px] Light – Dimming (Status) | 0 – 100 % |
| 90, 96, 102, 108, 114 | 1 Byte | – – – – – | DPT_Value_1_Ucount | 0 – 255 | [Btn][Px] | dummy | |
| 115 | 1 Byte | I | C – W –– | DPT_SceneControl | 0-63; 128-191 | [Thermostat] Scenes | 0 – 63 (Execute 1 – 64); 128 – 191 (Save 1 –64) |
| 116 | 2Bytes | I | C – W T U | DPT_Value_Temp | -273,00º – 670433,28º | [Tx] Temperature Source 1 | External Sensor Temperature |
| 117 | 2Bytes | I | C – W T U | DPT_Value_Temp | -273,00º – 670433,28º | [Tx] Temperature Source 2 | External Sensor Temperature |
| 118 | 2 Bytes | O | C R – T – | DPT_Value_Temp | -273,00º – 670433,28º | [Tx] Effective Temperature | Effective Control Temperature |
| 119 | 1 Byte | I | C – W – – | DPT_HVACMode | 1=Confort 2=Standby 3=Económico 4=Protección | [Tx] Special Mode | 1-Byte HVAC Mode |
| 120 | 1 Bit | I | C – W – – | DPT_Ack | 0/1 | [Tx] Special Mode: Comfort | 0 = Nothing; 1 = Trigger |
| 1 Bit | I | C – W – – | DPT_Switch | 0/1 | [Tx] Special Mode: Comfort | 0 = Off; 1 = On | |
| 121 | 1 Bit | I | C – W – – | DPT_Ack | 0/1 | [Tx] Special Mode: Standby | 0 = Nothing; 1 = Trigger |
| 1 Bit | I | C – W – – | DPT_Switch | 0/1 | [Tx] Special Mode: Standby | 0 = Off; 1 = On | |
| 122 | 1 Bit | I | C – W – – | DPT_Ack | 0/1 | [Tx] Special Mode: Economy | 0 = Nothing; 1 = Trigger |
| 1 Bit | I | C – W – – | DPT_Switch | 0/1 | [Tx] Special Mode: Economy | 0 = Off; 1 = On | |
| 123 | 1 Bit | I | C – W –– | DPT_Ack | 0/1 | [Tx] Special Mode: Protection | 0 = Nothing; 1 = Trigger |
| 1 Bit | I | C – W –– | DPT_Switch | 0/1 | [Tx] Special Mode: Protection | 0 = Off; 1 = On | |
| 124 | 1 Bit | I | C – W –– | DPT_Window_Door | 0/1 | [Tx] Window Status (Input) | 0 = Closed; 1 = Open |
| 125 | 1 Bit | I | C – W – – | DPT_Trigger | 0/1 | [Tx] Comfort Prolongation | 0 = Nothing; 1 = Timed Comfort |
| 126 | 1 Byte | O | C R – T– | DPT_HVACMode | 1=Confort 2=Standby 3=Económico 4=Protección | [Tx] Special Mode Status | 1-Byte HVAC Mode |
| 127 | 2Bytes | I | C – W –– | DPT_Value_Temp | -273,00º – 670433,28º | [Tx] Setpoint | Thermostat Setpoint Input |
| 2 Bytes | I | C – W –– | DPT_Value_Temp | -273,00º – 670433,28º | [Tx] Basic Setpoint | Reference Setpoint | |
| 128 | 1 Bit | I | C – W –– | DPT_Step | 0/1 | [Tx] Setpoint Step | 0 = Decrease Setpoint; 1 = Increase Setpoint |
| 129 | 2Bytes | I | C – W –– | DPT_Value_Tempd | -671088,64º – 670433,28º | [Tx] Setpoint Offset | Float Offset Value |
| 130 | 2Bytes | O | C R – T– | DPT_Value_Temp | -273,00º – 670433,28º | [Tx] Setpoint Status | Current Setpoint |
| 131 | 2Bytes | O | C R – T– | DPT_Value_Temp | -273,00º – 670433,28º | [Tx] Basic Setpoint Status | Current Basic Setpoint |
| 132 | 2Bytes | O | C R – T– | DPT_Value_Tempd | -671088,64º – 670433,28º | [Tx] Setpoint Offset Status | Current Setpoint Offset |
| 133 | 1 Bit | I | C – W –– | DPT_Reset | 0/1 | [Tx] Setpoint Reset | Reset Setpoint to Default |
| 1 Bit | I | C – W – – | DPT_Reset | 0/1 | [Tx] Offset Reset | Reset Offset | |
| 134 | 1 Bit | I | C – W – – | DPT_Heat_Cool | 0/1 | [Tx] Mode | 0 = Cool; 1 = Heat |
| 135 | 1 Bit | O | C R – T– | DPT_Heat_Cool | 0/1 | [Tx] Mode Status | 0 = Cool; 1 = Heat |
| 136 | 1 Bit | I | C – W – – | DPT_Switch | 0/1 | [Tx] On/Off | 0 = Off; 1 = On |
| 137 | 1 Bit | O | C R – T– | DPT_Switch | 0/1 | [Tx] On/Off Status | 0 = Off; 1 = On |
| 138 | 1 Bit | I/O | C R W –– | DPT_Switch | 0/1 | [Tx] Main System (Cool) | 0 = System 1; 1 = System 2 |
| 139 | 1 Bit | I/O | C R W –– | DPT_Switch | 0/1 | [Tx] Main System (Heat) | 0 = System 1; 1 = System 2 |
| 140 | 1 Bit | I | C – W –– | DPT_Enable | 0/1 | [Tx] Enable/Disable Secondary System (Cool) | 0 = Disable; 1 = Enable |
| 141 | 1 Bit | I | C – W –– | DPT_Enable | 0/1 | [Tx] Enable/Disable Secondary System (Heat) | 0 = Disable; 1 = Enable |
| 142, 148 | 1 Byte | O | C R – T– | DPT_Scaling | 0% – 100% | [Tx] [Sx] Control Variable (Cool) | PI Control (Continuous) |
|
143, 149 |
1 Byte | O | C R – T– | DPT_Scaling | 0% – 100% | [Tx] [Sx] Control Variable (Heat) | PI Control (Continuous) |
| 1 Byte | O | C R – T– | DPT_Scaling | 0% – 100% | [Tx] [Sx] Control Variable | PI Control (Continuous) | |
| 144, 150 | 1 Bit | O | C R – T– | DPT_Switch | 0/1 | [Tx] [Sx] Control Variable (Cool) | 2-Point Control |
| 1 Bit | O | C R – T– | DPT_Switch | 0/1 | [Tx] [Sx] Control Variable (Cool) | PI Control (PWM) | |
| 145, 151 | 1 Bit | O | C R – T– | DPT_Switch | 0/1 | [Tx] [Sx] Control Variable (Heat) | 2-Point Control |
| 1 Bit | O | C R – T – | DPT_Switch | 0/1 | [Tx] [Sx] Control Variable (Heat) | PI Control (PWM) | |
| 1 Bit | O | C R – T – | DPT_Switch | 0/1 | [Tx] [Sx] Control Variable | 2-Point Control | |
| 1 Bit | O | C R – T – | DPT_Switch | 0/1 | [Tx] [Sx] Control Variable | PI Control (PWM) | |
| 146, 152 | 1 Bit | O | C R – T– | DPT_Switch | 0/1 | [Tx] [Sx] PI State (Cool) | 0 = PI Signal 0%; 1 = PI Signal Greater than 0% |
| 147, 153 | 1 Bit | O | C R – T – | DPT_Switch | 0/1 | [Tx] [Sx] PI State (Heat) | 0 = PI Signal 0%; 1 = PI Signal Greater than 0% |
| 1 Bit | O | C R – T– | DPT_Switch | 0/1 | [Tx] [Sx] PI State | 0 = PI Signal 0%; 1 = PI Signal Greater than 0% | |
| 154, 158 | 2 Bytes | O | C R – T– | DPT_Value_Temp | -273,00º – 670433,28º | [Ix] Current Temperature | Temperature Sensor Value |
| 155, 159 | 1 Bit | O | C R – T – | DPT_Alarm | 0/1 | [Ix] Overcooling | 0 = No Alarm; 1 = Alarm |
| 156, 160 | 1 Bit | O | C R – T – | DPT_Alarm | 0/1 | [Ix] Overheating | 0 = No Alarm; 1 = Alarm |
| 157, 161 | 1 Bit | O | C R – T – | DPT_Alarm | 0/1 | [Ix] Probe Error | 0 = No Alarm; 1 = Alarm |
| 162 | 2 Bytes | O | C R – T – | DPT_Value_Temp | -273,00º – 670433,28º | [Internal Probe] Current Temperature | Temperature Sensor Value |
| 163 | 1 Bit | O | C R – T – | DPT_Alarm | 0/1 | [Internal Probe] Overcooling | 0 = No Alarm; 1 = Alarm |
| 164 | 1 Bit | O | C R – T – | DPT_Alarm | 0/1 | [Internal Probe] Overheating | 0 = No Alarm; 1 = Alarm |
| 165 | 1 Byte | I | C – W – – | DPT_SceneNumber | 0 – 63 | [Motion Detector] Scene Input | Scene Value |
| 166 | 1 Byte | C – – T – | DPT_SceneControl | 0-63; 128-191 | [Motion Detector] Scene Output | Scene Value | |
| 167, 196 | 1 Byte | O | C R – T– | DPT_Scaling | 0% – 100% | [Ix] Luminosity | 0-100% |
| 168, 197 | 1 Bit | O | C R – T– | DPT_Alarm | 0/1 | [Ix] Open Circuit Error | 0 = No Error; 1 = Open Circuit Error |
| 169, 198 | 1 Bit | O | C R – T– | DPT_Alarm | 0/1 | [Ix] Short Circuit Error | 0 = No Error; 1 = Short Circuit Error |
| 170, 199 | 1 Byte | O | C R – T– | DPT_Scaling | 0% – 100% | [Ix] Presence State (Scaling) | 0-100% |
| 171, 200 | 1 Byte | O | C R – T– | DPT_HVACMode | 1=Confort 2=Standby 3=Económico 4=Protección |
[Ix] Presence State (HVAC) | Auto, Comfort, Standby, Economy, Building Protection |
| 172, 201 | 1 Bit | O | C R – T– | DPT_Switch | 0/1 | [Ix] Presence State (Binary) | Binary Value |
| 1 Bit | O | C R – T– | DPT_Start | 0/1 | [Ix] Presence: Slave Output | 1 = Motion Detected | |
| 173, 202 | 1 Bit | I | C – W –– | DPT_Window_Door | 0/1 | [Ix] Presence Trigger | Binary Value to Trigger the Presence Detection |
| 174, 203 | 1 Bit | I | C – W – – | DPT_Start | 0/1 | [Ix] Presence: Slave Input | 0 = Nothing; 1 = Detection from slave device |
| 175, 204 | 2 Bytes | I | C – W –– | DPT_TimePeriodSec | 0 – 65535 | [Ix] Presence: Waiting Time | 0-65535 s. |
| 176, 205 | 2 Bytes | I | C – W –– | DPT_TimePeriodSec | 0 – 65535 | [Ix] Presence: Listening Time | 1-65535 s. |
| 177, 206 | 1 Bit | I | C – W –– | DPT_Enable | 0/1 | [Ix] Presence: Enable | According to parameters |
| 178, 207 | 1 Bit | I | C – W – – | DPT_DayNight | 0/1 | [Ix] Presence: Day/Night | According to parameters |
| 179, 208 | 1 Bit | O | C R – T – | DPT_Occupancy | 0/1 | [Ix] Presence: Occupancy State | 0 = Not Occupied; 1 = Occupied |
| 180, 209 | 1 Bit | I | C – W –– | DPT_Start | 0/1 | [Ix] External Motion Detection | 0 = Nothing; 1 = Motion detected by an external sensor |
| 181, 186, 191, 210, 215, 220 | 1 Byte | O | C R – T
– |
DPT_Scaling | 0% – 100% | [Ix] [ax] Detection State (Scaling) | 0-100% |
| 182, 187, 192, 211, 216, 221 | 1 Byte | O | C R – T– | DPT_HVACMode | 1=Confort 2=Standby 3=Económico 4=Protección | [Ix] [ax] Detection State (HVAC) | Auto, Comfort, Standby, Economy, Building Protection |
| 183, 188, 193, 212, 217,222 | 1 Bit | O | C R – T – | DPT_Switch | 0/1 | [Ix] [ax] Detection State (Binary) | Binary Value |
| 184, 189, 194, 213, 218, 223 | 1 Bit | I | C – W – – | DPT_Enable | 0/1 | [Ix] [ax] Enable Channel | According to parameters |
| 185, 190, 195, 214, 219, 224 | 1 Bit | I | C – W – – | DPT_Switch | 0/1 | [Ix] [ax] Force State | 0 = No Detection; 1 = Detection |
| 225, 231 | 1 Bit | I | C – W – – | DPT_Enable | 0/1 | [Ix] Input Lock | 0 = Unlock; 1 = Lock |
| 226, 232 | 1 Bit | C – – T – | DPT_Switch | 0/1 | [Ix] [Short Press] 0 | Sending of 0 | |
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Ix] [Short Press] 1 | Sending of 1 | ||
| 1 Bit | I | C – W T – | DPT_Switch | 0/1 | [Ix] [Short Press] 0/1 Switching | Switching 0/1 | |
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Ix] [Short Press] Move Up Shutter | Sending of 0 (Up) | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Ix] [Short Press] Move Down Shutter | Sending of 1 (Down) | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Ix] [Short Press] Move Up/Down Shutter | Switching 0/1 (Up/Down) | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Ix] [Short Press] Stop/Step Up Shutter | Sending of 0 (Stop/Step Up) | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Ix] [Short Press] Stop/Step Down Shutter | Sending of 1 (Stop/Step Down) | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Ix] [Short Press] Stop/Step Shutter (Switched) | Switching of 0/1 (Stop/Step Up/Down) | ||
| 4 Bit | C – – T – | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Ix] [Short Press] Brighter | Increase Brightness | ||
| 4 Bit | C – – T – | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Ix] [Short Press] Darker | Decrease Brightness |
| 4 Bit | C – – T – | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) …0xF (Subir 1%) |
[Ix] [Short Press] Brighter/Darker | Switch Bright/Dark | ||
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Ix] [Short Press] Light On | Sending of 1 (On) | ||
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Ix] [Short Press] Light Off | Sending of 0 (Off) | ||
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Ix] [Short Press] Light On/Off | Switching 0/1 | |
| 1 Byte | C – – T – | DPT_SceneControl | 0-63; 128-191 | [Ix] [Short Press] Run Scene | Sending of 0 – 63 | ||
| 1 Byte | C – – T – | DPT_SceneControl | 0-63; 128-191 | [Ix] [Short Press] Save Scene | Sending of 128 – 191 | ||
| 1 Bit | I/O | C R W T – | DPT_Switch | 0/1 | [Ix] [Switch/Sensor] Edge | Sending of 0 or 1 | |
| 1 Byte | C – – T – | DPT_Value_1_Ucount | 0 – 255 | [Ix] [Short Press] Constant Value (Integer) | 0 – 255 | ||
| 1 Byte | C – – T – | DPT_Scaling | 0% – 100% | [Ix] [Short Press] Constant Value (Percentage) | 0% – 100% | ||
| 2 Bytes | C – – T – | DPT_Value_2_Ucount | 0 – 65535 | [Ix] [Short Press] Constant Value (Integer) | 0 – 65535 | ||
| 2 Bytes | C – – T – | 9.xxx | -671088,64 – 670433,28 | [Ix] [Short Press] Constant Value (Float) | Float Value | ||
| 227, 233 | 1 Byte | I | C – W –– | DPT_Scaling | 0% – 100% | [Ix] [Short Press] Shutter Status (Input) | 0% = Top; 100% = Bottom |
| 1 Byte | I | C – W –– | DPT_Scaling | 0% – 100% | [Ix] [Short Press] Dimming Status (Input) | 0% – 100% | |
| 228, 234 | 1 Bit | C – – T – | DPT_Switch | 0/1 | [Ix] [Long Press] 0 | Sending of 0 | |
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Ix] [Long Press] 1 | Sending of 1 | ||
| 1 Bit | I | C – W T– | DPT_Switch | 0/1 | [Ix] [Long Press] 0/1 Switching | Switching 0/1 | |
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Ix] [Long Press] Move Up Shutter | Sending of 0 (Up) | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Ix] [Long Press] Move Down Shutter | Sending of 1 (Down) | ||
| 1 Bit | C – – T – | DPT_UpDown | 0/1 | [Ix] [Long Press] Move Up/Down Shutter | Switching 0/1 (Up/Down) | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Ix] [Long Press] Stop/Step Up Shutter | Sending of 0 (Stop/Step Up) | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Ix] [Long Press] Stop/Step Down Shutter | Sending of 1 (Stop/Step Down) | ||
| 1 Bit | C – – T – | DPT_Step | 0/1 | [Ix] [Long Press] Stop/Step Shutter (Switched) | Switching of 0/1 (Stop/Step Up/Down) | ||
| 4 Bit | C – – T – | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) |
[Ix] [Long Press] Brighter | Long Pr. -> Brighter; Release -> Stop |
| 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
|||||||
| 4 Bit |
C – – T – |
DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Ix] [Long Press] Darker |
Long Pr. -> Darker; Release -> Stop |
||
| 4 Bit | C – – T – | DPT_Control_Dimming | 0x0 (Detener) 0x1 (Reducir 100%) … 0x7 (Reducir 1%) 0x8 (Detener) 0x9 (Subir 100%) … 0xF (Subir 1%) |
[Ix] [Long Press] Brighter/Darker | Long Pr. -> Brighter/Darker; Release -> Stop | ||
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Ix] [Long Press] Light On | Sending of 1 (On) | ||
| 1 Bit | C – – T – | DPT_Switch | 0/1 | [Ix] [Long Press] Light Off | Sending of 0 (Off) | ||
| 1 Bit | I | C – W T
– |
DPT_Switch | 0/1 | [Ix] [Long Press] Light On/Off | Switching 0/1 | |
| 1 Byte | C – – T – | DPT_SceneControl | 0-63; 128-191 | [Ix] [Long Press] Run Scene | Sending of 0 – 63 | ||
| 1 Byte | C – – T – | DPT_SceneControl | 0-63; 128-191 | [Ix] [Long Press] Save Scene | Sending of 128 – 191 | ||
| 1 Bit | O | C R – T – | DPT_Alarm | 0/1 | [Ix] [Switch/Sensor] Alarm: Breakdown or Sabotage | 1 = Alarm; 0 = No Alarm | |
| 2 Bytes | C – – T – | 9.xxx | -671088,64 – 670433,28 | [Ix] [Long Press] Constant Value (Float) | Float Value | ||
| 2 Bytes | C – – T – | DPT_Value_2_Ucount | 0 – 65535 | [Ix] [Long Press] Constant Value (Integer) | 0 – 65535 | ||
| 1 Byte | C – – T – | DPT_Scaling | 0% – 100% | [Ix] [Long Press] Constant Value (Percentage) | 0% – 100% | ||
| 1 Byte | C – – T – | DPT_Value_1_Ucount | 0 – 255 | [Ix] [Long Press] Constant Value (Integer) | 0 – 255 | ||
| 229, 235 | 1 Bit | C – – T – | DPT_Trigger | 0/1 | [Ix] [Long Press/Release] Stop Shutter | Release -> Stop Shutter | |
|
230, 236 |
1 Byte | I | C – W –– | DPT_Scaling | 0% – 100% | [Ix] [Long Press] Dimming Status (Input) | 0% – 100% |
| 1 Byte | I | C – W –– | DPT_Scaling | 0% – 100% | [Ix] [Long Press] Shutter Status (Input) | 0% = Top; 100% = Bottom |
Join and send us your inquiries about Zennio devices:
https://support.zennio.com
Zennio Avance y Tecnología S.L.
C/ Río Jarama, 132. Nave P-8.11
45007 Toledo (Spain).
Tel. +34 925 232 002.
www.zennio.com
info@zennio.com
Documents / Resources
 |
Zennio Tecla X KNX Multifunction Capacitive Touch Switch [pdf] User Manual ZVITX1, ZVITX2, ZVITX4, ZVITX6, ZVITX8, Tecla X, Tecla X KNX Multifunction Capacitive Touch Switch, KNX Multifunction Capacitive Touch Switch, Multifunction Capacitive Touch Switch, Capacitive Touch Switch, Touch Switch |