Multifunctional Pager

Appearance Introduction

1. Receiver (TY03 Not includes rechargeable battery)

A compact device featuring an alarm indicator lamp, built-in speaker, SOS button, Wi-Fi indicator, hanging board buckle, USB DC 5V power port, and an external siren interface. It displays compliance marks: [CE, FC, ROHS].

Diagram shows the receiver with labeled components.

2. SOS Button

A small, circular device equipped with a strap clip, an indicator light, and a button for activation.

Diagram shows the SOS button with its strap clip, indicator light, and button.

Power On

Turn on the power switch before performing all operations.

Diagram illustrates connecting the TY06 Receiver (with rechargeable battery) to a USB power cable, showing an LED lighting up. The SOS button is also shown.

Receiver Pairs with SOS Button

1. How to Pair the SOS Button with Receiver

Short press the key on the back of the Receiver for 1 second. The Receiver will emit a 'beep' sound for 15 seconds.

Diagram shows a hand pressing the receiver's back button, with a 'Beep' indicator.

Short press the SOS Button. The Receiver will stop 'beep' upon successful pairing.

Diagram shows a hand pressing the SOS button, followed by receiver alarms with flashing SOS and sound.

2. Test If The Pairing Is Successful.

The SOS Button must be used within a 230ft/70m range of the Receiver. The SOS Button cannot be brought outside this range.

Diagram illustrates the effective distance between the SOS button and receiver.

Press the SOS Button.

The Receiver will alarm, indicated by a continuously flashing SOS light and an alarm sound for approximately 30 seconds.

Note: Alarms can be removed in the APP.

Connect with Mobile APP

1. Download APP

Scan the provided QR codes to download the respective applications. Alternatively, search for 'Tuya Smart' or 'Smart Life' in your application market.

Diagrams show QR codes for 'Tuya Smart' and 'Smart Life' apps.

2. Notes on distribution network

Wi-Fi Frequency: Supports 2.4GHz, does not support 5GHz.

Diagram shows a receiver with Wi-Fi signal.

The distance between the Receiver and the Wi-Fi signal source should be less than 20m/66ft for optimal performance; closer proximity is better.

Environmental Note: Performance varies with the environment. If the Receiver is too far from the router, it may not connect to the smartphone.

Connect the Receiver to APP

Both 'Tuya Smart' and 'Smart Life' apps are similar; choose one for use.

1. Ensure your cell phone is connected to 2.4GHz Wi-Fi and Bluetooth is enabled.
2. Long press the key on the back of the Receiver for 6 seconds to enter the distribution network mode. The green light will flash continuously.
3. Diagram shows a phone screen with Wi-Fi and Bluetooth enabled, and a hand pressing the receiver's back button.
4. Open the chosen APP and tap 'Add Device'.
5. Diagram shows the app interface with an 'Add Device' button.
6. After the device is automatically discovered, tap 'Add'.
7. Diagram shows the app discovering devices and an 'Add' button.
8. Confirm your Wi-Fi network name and password, then tap 'Next'.
9. Diagram shows a Wi-Fi login screen.
10. Wait for a successful connection.
11. Diagram shows a progress indicator for adding a device.
12. Tap 'Done'.
13. Diagram shows a 'Done' button.
14. The Receiver's status page will appear in the APP, showing options like 'Disarmed', 'Away', 'Home', 'Trigger alarm', 'History records', 'Accessories', and 'Setting'.

Connect the SOS Button to APP

1. On the Receiver's page in the APP, scroll to the bottom and tap 'Accessories'.
2. Diagram shows the receiver's page in the app with the 'Accessories' option highlighted.
3. Tap the '+' icon in the upper right corner.
4. Diagram shows the Accessories screen with a '+' icon.
5. Once the Receiver beeps, short press the SOS Button.
6. Diagram shows the app interface for quick add device with a timer, and the SOS button being pressed.
7. Wait for a successful connection confirmation, then tap 'Confirm'.
8. Diagram shows a 'Device add success' confirmation.

APP Notification Setting

1. Tap 'Me' on the app's main screen, then tap the settings icon [gear icon] in the upper right corner.
2. Diagram shows the app's 'Me' tab and a settings icon.
3. Tap 'App Notification'.
4. Diagram shows the Settings menu with 'App Notification' highlighted.
5. Tap 'Notifications'.
6. Diagram shows the Notifications Settings screen.
7. Ensure Bluetooth and Local Network are enabled in your phone's settings, then tap 'Notifications' within the app's settings.
8. Diagram shows phone settings for Bluetooth, Local Network, and Notifications.
9. Enable 'Allow Notifications', 'Sounds', and 'Badges'. Choose your preferred alert methods (e.g., Banners, Lock Screen, Notification Center).
10. Diagram shows notification settings for the app, including Banners, Sounds, Badges.

Important Note: If your phone is in Silent mode, it will not ring for alerts. Ensure your phone is in Ring mode to receive audible alerts when the SOS button is pressed.

APP Operation

1. Steps to Remove Alarm

1. Press the SOS Button.
2. The Receiver will alarm with flashing lights and sound for about 30 seconds.
3. Tap 'Alarm remove' on the app interface.

Diagram shows the app interface with an 'Alarm remove' button.

2. Mutiple People Sharing

1. On the Receiver's page in the APP, tap the share icon [share icon] in the upper right corner.
2. Diagram shows the receiver's page with a share icon.
3. Tap 'Share Device'.
4. Diagram shows the sharing options.
5. Tap 'Add Sharing'.
6. Diagram shows the 'Add Sharing' screen.
7. Select your preferred sharing method: Share with Account, Share with Recent Contacts, or Share with Others.
8. Diagram shows various sharing methods.

3. Steps to Set Alarm Ringtone

1. On the Receiver's page in the APP, scroll to the bottom and tap 'Accessories'.
2. Diagram shows the receiver's page with 'Accessories' highlighted.
3. Tap on the specific detector, e.g., 'Detector01'.
4. Diagram shows the Accessories list with a specific detector.
5. Tap 'alarm ringtone'.
6. Diagram shows the settings for the detector, with 'alarm ringtone' highlighted.
7. Choose your preferred ringtone from the list (e.g., Ding Dong+Ding, Alarm sound, Westminster Quarters, For Alice).
8. Diagram shows a list of ringtone options.
9. Tap 'Save'.
10. Diagram shows a 'Save' button.

4. Steps to Set Alarm Time

1. On the Receiver's page in the APP, scroll to the bottom and tap 'Setting'.
2. Diagram shows the receiver's page with 'Setting' highlighted.
3. Tap 'Alarm time'.
4. Diagram shows the setting menu with 'Alarm time' highlighted.
5. Choose the desired alarm duration (e.g., 0s, 28, 29, 30s, 31, 32) and tap 'Confirm'.
6. Diagram shows alarm duration options.

5. Steps to Set Alarm Volume

1. On the Receiver's page in the APP, scroll to the bottom and tap 'Setting'.
2. Diagram shows the receiver's page with 'Setting' highlighted.
3. Tap 'Alarm volume'.
4. Diagram shows the setting menu with 'Alarm volume' highlighted.
5. Choose the desired alarm volume level (e.g., Low, Middle, High, Mute) and tap 'Confirm'.
6. Diagram shows alarm volume options.

6. Steps to Set Brightness

1. On the Receiver's page in the APP, scroll to the bottom and tap 'Setting'.
2. Diagram shows the receiver's page with 'Setting' highlighted.
3. Tap 'Alarm light brightness'.
4. Diagram shows the setting menu with 'Alarm light brightness' highlighted.
5. Choose the desired brightness level (e.g., 0, 1, 2, 100) and tap 'Confirm'.
6. Diagram shows alarm light brightness options.

7. Delete SOS Button

1. On the Receiver's page in the APP, scroll to the bottom and tap 'Accessories'.
2. Diagram shows the receiver's page with 'Accessories' highlighted.
3. Slide the accessory entry to the left.
4. Diagram shows sliding an accessory to the left.
5. Tap 'Delete'.
6. Diagram shows a delete button.
7. Tap 'Confirm' to confirm the sub-device removal.
8. Diagram shows a confirmation prompt for sub-device removal.

8. Clear all accessories

1. On the Receiver's page in the APP, scroll to the bottom and tap 'Setting'.
2. Diagram shows the receiver's page with 'Setting' highlighted.
3. Tap 'all clear device'.
4. Diagram shows the setting menu with 'all clear device' highlighted.
5. Tap 'Confirm' to clear all connected devices.
6. Diagram shows a confirmation prompt for clearing devices.

9. Unbind mobile APP

1. On the Receiver's page in the APP, tap the share icon [share icon] in the upper right corner.
2. Diagram shows the receiver's page with a share icon.
3. Tap 'Remove Device'.
4. Diagram shows the device options with 'Remove Device' highlighted.

Installation

1. Receiver Installation

Installation Distance: The Receiver's distance from the router network should be within 20m/66ft; closer is better.

Diagram shows a receiver and a router, indicating distance.

Note: The APP's functions cannot be used if the Receiver is not connected to the APP via Wi-Fi.

2. 2 ways to place

1. On the table

Diagram shows the receiver placed on a table.

2. Wall mounting

Diagram shows the receiver mounted on a wall.

3. Wall-mounted installation steps

a. Mark the wall with 2 mounting hole locations and drill 2 holes for wall plugs.

Diagram shows marking and drilling holes.

b. Use a Phillips screwdriver to twist in 2 screws clockwise into the 2 holes.

Diagram shows screwing in screws.

c. Align the Receiver with the hanging plate buckle and attach it.

Diagram shows attaching the receiver to the hanging buckle.

d. Connect the Receiver to the USB power cable.

Diagram shows connecting the USB cable.

SOS Button Battery Change

Tools required: Strap Clip, Mini Screwdriver.

Diagram shows the components for changing the SOS button battery.

Phone Alert: To receive alarm messages and alerts on your phone, ensure notification switches are enabled in both the TUYA APP and your phone's settings.

Notes

1. The distance between the Receiver and the Wi-Fi signal needs to be less than 20m/66ft (closer is better).
2. Diagram shows distance between receiver and Wi-Fi.
3. The SOS Button needs to be used within a 70m/230ft range of the Receiver. The SOS Button cannot be brought outside this range.
4. Diagram shows distance between SOS button and receiver.

Specification

• Operating voltage: 5V
• Static current: ≥60mA
• Alarm current: ≤200mA
• Wireless frequency: 433.92MHz
• Wi-Fi: IEEE 802.11 b/g/n 2.4G
• Working temperature: -10℃~50℃

Q&A

1. Q: Does the Receiver need to plug in USB power cable all the time?

A: For regular Receivers, yes. For models with a rechargeable battery, it is not necessary when fully charged. A fully charged receiver will operate even during a power outage. Check the remaining battery level in the TUYA APP to determine when to charge.

2. Q: What if the SOS Button cannot make the Receiver alarm?

A: 1. Verify the SOS Button has been successfully paired with the Receiver. 2. Ensure the SOS Button has power (press it to see if the indicator light turns on). 3. Confirm the SOS Button is within the 230ft/70m range of the Receiver.

3. Q: What if the Receiver cannot connect to smartphone?

A: 1. Ensure your smartphone and Receiver are on the same Wi-Fi network. 2. The distance between the Receiver and Wi-Fi signal should be less than 66ft/20m (closer is better). 3. Confirm your Wi-Fi frequency is 2.4GHz.

4. Q: Can I take the SOS Button outside?

A: No, the SOS Button must be used within 230ft/70m of the Receiver, and the Receiver must be within 66ft/20m of the Wi-Fi source (closer is better).

Attention

Dear Customer: Thank you for purchasing our WIFI wireless pager. As a WiFi-connected smart product, its performance depends on your home wireless network stability and your cell phone's wireless signal strength. When the network is stable, pressing and holding the SOS Button will trigger an immediate alarm on the Receiver and send a signal to the TUYA APP on your cell phone. If the network is unstable, the Receiver may not receive signals or alarm. In such cases, press the SOS Button multiple times until an alarm sounds. Once an alarm sound is issued, a signal will be sent to the TUYA APP, and your phone will receive an alert message. We are committed to improving user experience and ensuring customer satisfaction with our products. For any questions, please contact us via Amazon email for a satisfactory response.

After sales service

Service Guarantee: We offer a 30-day return service. Our product manuals provide detailed operating instructions to help you use our products effectively. You can also watch operation videos on the product page or contact us for them. For any inquiries, please contact us via Amazon email for assistance.