1. Ifihan
The WRINERY Pulse Oximeter Fingertip is designed to measure blood oxygen saturation levels (SpO2), pulse rate, and pulse strength. This device is intended for non-medical use, suitable for home and travel. It provides accurate and reliable data before and after strenuous activities. It is ideal for sports enthusiasts, aviators, trainers, bikers, mountain climbers, or anyone interested in monitoring their SpO2 on the go.
Note: This pulse oximeter is not intended for medical diagnosis or treatment.
2. Package Awọn akoonu
Jẹrisi pe gbogbo awọn ohun kan wa ninu package:
- 1 x WRINERY Finger Oxygen and Heart Rate Monitor
- 1 x Lanyard
- 1 x Itọsọna olumulo (iwe yii)
- 2 x AAA batiri
- 1 x Apo gbigbe
Image: Contents of the WRINERY Pulse Oximeter package, showing the device, lanyard, two AAA batteries, and a black carrying case.
3. Eto
Follow these steps to prepare your pulse oximeter for first use:
- Fi Awọn batiri sii: Remove the back cover of the device. Insert the two AAA batteries into the battery compartment, ensuring correct polarity (+/-). Replace the back cover.
Image: The WRINERY Pulse Oximeter device shown with its accessories, illustrating the components involved in the initial setup, including the battery compartment.
4. Awọn ilana Iṣiṣẹ
To obtain a reading:
- Fi Ika sii: Ṣii clamp of the oximeter. Insert one of your fingers (preferably the index or middle finger) into the rubber opening, ensuring your fingertip is aligned with the red light sensor.
- Mu Ẹrọ ṣiṣẹ: Tu clamp. The device will automatically switch on and begin measurement.
- Ka Awọn abajade: Remain still. After approximately eight to ten seconds, your SpO2 (blood oxygen saturation) and Pulse Rate (PRbpm) will be displayed on the OLED screen.
For accurate readings, it is recommended to use the device in a stationary condition, avoiding movement during measurement.
Image: A finger being correctly inserted into the WRINERY Pulse Oximeter, highlighting the position for accurate measurement over the red light sensor.
Image: The WRINERY Pulse Oximeter's OLED display, indicating SpO2 value, power indicator, pulse bar graph, operating button, heart beat icon, pulse rate, and pulse waveform.
5. Awọn ẹya ara ẹrọ
- Deede ati Gbẹkẹle: Provides precise measurements of blood oxygen levels and pulse rate within 8 seconds.
- Apẹrẹ to gbe: Compact and lightweight (approximately 65g / 1.95 ounces) with an included lanyard for easy carrying.
- Wide Finger Size Accommodation: Designed to fit a broad range of finger sizes, from children to adults.
- Minimum Power Consumption: Features an automatic power-off function when no finger is detected, extending battery life up to 15 hours with two AAA batteries.
- Crystal Clear OLED Display: Presents reading data on a bright and sharp OLED screen for enhanced visibility in various environments.
6. Awọn pato
| Orukọ awoṣe | WRINERY |
| Measuring Range SpO2 | 35% ~ 100% |
| Measuring Range Pulse Rate (PR) | 25 BPM ~250 BPM |
| Awọn batiri | 2 x AAA batiri (pẹlu) |
| Igbesi aye batiri | Titi di awọn wakati 15 ti iṣẹ ilọsiwaju |
| Ifihan Iru | OLED |
| Àwọ̀ | Dudu |
| Package Mefa | 3.19 x 2.24 x 2.13 inches |
| Iwọn | 2.4 ounces (device only approx. 0.5 ounces) |
| Olupese | Hunan Accurate Bio-Medical Technology Co., Ltd. |
| ASIN | B07V3176CB |
7. Itọju
Itọju to peye ṣe idaniloju gigun ati deede ti ẹrọ rẹ:
- Ninu: Wipe the surface of the oximeter with a soft cloth dampened with medical alcohol or a mild disinfectant. Do not immerse the device in liquid.
- Ibi ipamọ: Tọju ẹrọ naa ni itura, aye gbigbẹ, kuro lati orun taara, awọn iwọn otutu ti o ga, ati ọriniinitutu.
- Rirọpo Batiri: Replace batteries when the low battery indicator appears on the display. If the device will not be used for an extended period, remove the batteries to prevent leakage.
- Yago fun Ipa: Mu ẹrọ naa pẹlu iṣọra lati yago fun ibajẹ lati awọn sisọ tabi awọn ipa.
8. Laasigbotitusita
If you encounter issues with your WRINERY Pulse Oximeter, refer to the following common problems and solutions:
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Ko si ifihan lẹhin agbara lori | Awọn batiri ti ku tabi ti fi sori ẹrọ ti ko tọ. | Replace batteries or re-install them with correct polarity. |
| Àwọn ìwé kíkà tí kò péye tàbí tí kò dúró ṣinṣin | Finger not inserted properly; movement during measurement; cold fingers; nail polish or artificial nails. | Re-insert finger correctly; remain still; warm hands; remove nail polish/artificial nails. |
| Device automatically turns off | No finger detected for a period (normal auto-off function); low battery. | This is normal behavior if no finger is present. If a finger is present, check/replace batteries. |
9. Alaye Aabo pataki
- This device is intended for sports and aviation use only. It is not a medical device and should not be used for medical diagnosis or treatment.
- Consult a medical professional for any health concerns.
- Pa mọ́ kúrò lọ́wọ́ àwọn ọmọdé. Àwọn ẹ̀yà kékeré lè fa ewu fífún ni.
- Ma ṣe lo ẹrọ naa ni agbegbe MRI tabi CT.
- Do not use the device on the same limb simultaneously with a blood pressure cuff or other monitoring equipment.
10. Atilẹyin ọja ati Support
For warranty information or technical support, please refer to the contact details provided with your purchase or visit the official WRINERY webojula. Jọwọ ṣe idaduro ẹri rira rẹ fun awọn iṣeduro atilẹyin ọja.