TC Electronic JUNE-60 CHORUS Pedal Instruction Manual

1. Ifihan

The TC Electronic JUNE-60 CHORUS pedal is an authentic recreation of the legendary synthesizer chorus from the 1980s. This pedal features a simple 2-button interface for intuitive modulation tone and utilizes all-analog BBD (Bucket Brigade Delay) circuitry to deliver its classic sound. Designed for guitarists seeking vintage chorus effects, the JUNE-60 CHORUS also includes True Bypass for ultimate signal integrity.

TC Electronic JUNE-60 CHORUS Pedal, top-down view

olusin 1.1: Top-isalẹ view of the TC Electronic JUNE-60 CHORUS Pedal, showcasing its two yellow buttons and True Bypass footswitch.

2. Awọn Ilana Aabo pataki

Ka awọn itọnisọna wọnyi daradara ṣaaju ki o to ṣiṣẹ ẹrọ naa.
Pa awọn ilana wọnyi fun itọkasi ọjọ iwaju.
Heed all warnings on the product and in the instructions.
Maṣe lo ohun elo yii nitosi omi tabi ọrinrin.
Mọ pẹlu asọ gbigbẹ nikan.
Ma ṣe dina eyikeyi awọn ṣiṣi atẹgun. Fi sori ẹrọ ni ibamu pẹlu awọn ilana ti olupese.
Maṣe fi sori ẹrọ nitosi awọn orisun ooru gẹgẹbi awọn imooru, awọn iforukọsilẹ ooru, awọn adiro, tabi awọn ohun elo miiran (pẹlu ampliifiers) ti o gbe ooru jade.
Lo awọn asomọ/awọn ẹya ara ẹrọ ti olupese pato.
Tọkasi gbogbo iṣẹ si awọn oṣiṣẹ iṣẹ ti o peye. Iṣẹ nilo nigbati ohun elo ba ti bajẹ ni ọna eyikeyi, gẹgẹbi okun ipese agbara tabi plug ti bajẹ, omi ti ta silẹ tabi awọn nkan ti ṣubu sinu ẹrọ, ohun elo naa ti farahan si ojo tabi ọrinrin, ko ṣiṣẹ deede. , tabi ti lọ silẹ.

3. Eto

3.1 Asopọ agbara

The JUNE-60 CHORUS pedal can be powered by a 9V battery or an external 9V DC power supply (not included). Ensure the power supply provides at least 100 mA. Connect the power supply to the 9V DC input jack on the rear of the pedal.

Agbara Batiri: To install a 9V battery, open the battery compartment on the bottom of the pedal. Connect the battery to the clip and place it inside the compartment.
Agbara ita: Use a regulated 9V DC power supply with a center-negative plug, providing a minimum of 100 mA.

TC Electronic JUNE-60 CHORUS Pedal rear panel with input, output, and power jacks

Figure 3.1: Rear panel of the JUNE-60 CHORUS Pedal, showing the INPUT (MONO), 9V DC power input (100 mA), and OUTPUT (MONO/STEREO) jacks.

3.2 Awọn isopọ Ohun

So ohun èlò orin rẹ (fún àpẹẹrẹ, gítà) mọ́ INPUT (MONO) jack using a standard 1/4-inch instrument cable. Connect the IJADE (MONO/StereO) jack si rẹ amplifier or the next pedal in your signal chain. For stereo operation, use a Y-cable or two separate cables from the output to two ampàwọn ohun èlò ìfàmọ́ra tàbí ẹ̀rọ ìtẹ̀síwájú sítíréò.

Eto Mono: Connect a single 1/4-inch cable from the OUTPUT jack to your amplifier.
Eto Sitẹrio: The JUNE-60 CHORUS supports stereo output. Consult your amplifier or audio interface manual for proper stereo input connections.

4. Isẹ

The JUNE-60 CHORUS pedal features a straightforward 2-button interface, replicating the classic chorus modes of its inspiration. The pedal is activated by the True Bypass footswitch.

4.1 Engaging the Effect

Tẹ awọn OFO TODAJU footswitch to toggle the effect on or off. When the effect is active, the LED indicator will illuminate.

4.2 Chorus Modes (Buttons I & II)

The two yellow buttons, labeled I ati II, select different chorus modes. These buttons can be used individually or simultaneously to achieve distinct modulation characteristics.

Bọtini I: Engages Chorus Mode I, offering a specific modulation rate and depth.
Bọtini II: Engages Chorus Mode II, offering an alternative modulation rate and depth.
Buttons I & II (Simultaneously): Pressing both buttons together activates a combined chorus mode, often resulting in a richer, more complex modulation. Experiment with these combinations to find your desired sound.

TC Electronic JUNE-60 CHORUS Pedal top view showing buttons I and II

olusin 4.1: Top view of the JUNE-60 CHORUS Pedal, highlighting the two yellow buttons (I and II) for chorus mode selection.

4.3 Mono/Stereo Switch

A small switch labeled MONO / sitẹrio is located near the chorus mode buttons. This switch determines the output configuration of the pedal.

BUN: Fun nikan amplifier setups.
Sitẹrio: For dual amplifier or stereo input setups, providing a wider, more immersive chorus effect.

5. Itọju

5.1 Ninu

Clean the pedal's exterior with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or internal components.

5.2 Batiri Rirọpo

If using battery power, replace the 9V battery when the effect LED dims or the pedal's performance degrades. To replace, open the battery compartment on the bottom of the unit, disconnect the old battery, and connect a new one, ensuring correct polarity.

5.3 Ibi ipamọ

When not in use for extended periods, disconnect the power supply and remove the battery to prevent leakage. Store the pedal in a cool, dry place away from direct sunlight and extreme temperatures.

6. Laasigbotitusita

Isoro	Owun to le Fa	Ojutu
Ko si ohun nigba ti efatelese wa ni npe.	No power, incorrect cable connection, faulty cable.	Check power supply connection and ensure it meets 9V DC, 100mA specifications. Replace battery if using battery power. Daju gbogbo awọn kebulu ohun ti sopọ ni aabo. Test cables with another device to ensure they are not faulty.
Ohùn alailagbara tabi daru.	Low battery, incorrect input level from instrument.	Replace battery or use external power supply. Ensure instrument output level is appropriate for pedal input.
Chorus effect is not noticeable.	Incorrect chorus mode selected, subtle setting.	Experiment with pressing Button I, Button II, or both simultaneously. Ensure the MONO/STEREO switch is set correctly for your setup.
Pedal does not power on with adapter.	Insufficient current from power adapter.	Verify your power adapter provides at least 100 mA at 9V DC. Some adapters may provide 9V but insufficient current.

7. Awọn pato

Ẹya ara ẹrọ	Ẹ̀kúnrẹ́rẹ́
Awoṣe	JUNE-60 CHORUS
Iru Ipa	Egbe
Ayika	All-analog BBD (Bucket Brigade Delay)
Fori	Otitọ Otitọ
Awọn iṣakoso	2 x Chorus Mode Buttons (I, II), MONO/STEREO Switch, True Bypass Footswitch
Asopọ Input	1 x 1/4" TS, unbalanced (Mono)
Asopọ O wu	1 x 1/4" TS, unbalanced (Mono/Stereo)
Agbara Input	Standard 9V DC, center-negative, >100 mA (Power supply not included)
Aṣayan batiri	Batiri 9V (ko si)
Awọn iwọn (H x W x D)	Isunmọ 13.7 x 8.6 x 5.6 inches
Iwọn	8 iwon (0.5 lbs)
Ohun elo ara	Ṣiṣu, Irin

TC Electronic JUNE-60 CHORUS Pedal bottom label with regulatory information

Figure 7.1: Bottom label of the JUNE-60 CHORUS Pedal, displaying model and regulatory compliance information.

8. Atilẹyin ọja ati Support

8.1 atilẹyin ọja Alaye

TC Electronic products are designed and manufactured to the highest standards. For detailed warranty terms and conditions, please refer to the official TC Electronic webaaye tabi kaadi atilẹyin ọja ti o wa pẹlu ọja rẹ. Jeki ẹri rira rẹ fun eyikeyi awọn ibeere atilẹyin ọja.

8.2 Onibara Support

Should you encounter any issues or have questions regarding your JUNE-60 CHORUS pedal, please visit the official TC Electronic support page for FAQs, troubleshooting guides, and contact information. You can find support resources at the Atilẹyin Itanna TC Webojula.