Ìwé Ìtọ́sọ́nà fún Ètò Ìwẹ̀nùmọ́ Fáìlì Clarisonic Mia 2 Sonic

1. Ifihan

The Clarisonic Mia 2 Sonic Facial Cleansing Brush System utilizes patented micro-massage oscillation technology to cleanse the skin. This device is designed to gently remove impurities, preparing the skin for better absorption of creams, serums, and moisturizers. It offers two different speeds and a one-minute pulsing T-timer for customized cleansing.

Regular use can help improve skin texture, tone, and contribute to healthier-looking skin. This manual provides instructions for the proper setup, operation, and maintenance of your Clarisonic Mia 2 device.

2. Package Awọn akoonu

Verify that all items are present in your Clarisonic Mia 2 package:

• Mia 2 Cleansing Device
• Ṣaja
• Radiance Cleansing Brush Head
• Refreshing Trial Size Gel Cleanser, 1 fl. oz.

3. Alaye Aabo

Please read and understand all safety precautions before using the Clarisonic Mia 2 device.

• Always remove eye makeup by hand before using the device.
• Ma ṣe lo ẹrọ naa lori awọ fifọ tabi ti o binu.
• Jeki ẹrọ naa kuro ni arọwọto awọn ọmọde.
• Avoid direct contact with eyes during operation.
• Do not use the device with harsh chemicals or abrasive cleansers.
• Allow the device to dry completely after each use.
• Store the device in a dry place when not in use.

4. Eto

4.1 Gbigba agbara akọkọ

Before first use, fully charge your Clarisonic Mia 2 device. A full charge typically takes approximately 18 hours. A fully charged device provides approximately 80-100 minutes of use, depending on the selected speed setting.

1. So ṣaja pọ si iṣan agbara kan.
2. Place the bottom of the Mia 2 device onto the magnetic charging cradle. Ensure the device is securely seated and the charging indicator light (if present) illuminates.
3. Gba ẹrọ laaye lati gba agbara fun iye akoko ti a ṣeduro.

4.2 Attaching awọn fẹlẹ Head

To attach a brush head, align the three tabs on the back of the brush head with the three slots on the device handle. Push down and twist clockwise until it locks into place. To remove, twist counter-clockwise and pull up.

5. Awọn ilana Iṣiṣẹ

Follow these steps for effective facial cleansing with your Clarisonic Mia 2:

1. Mura Awọ: If you wear makeup, remove eye makeup by hand before using the device.
2. Wet Skin and Brush Head: Wet your skin and the brush head with warm water.
3. Apply Cleanser: Apply your preferred cleanser directly to your skin or to the wet brush head.
4. Power On and Cleanse: Turn your Clarisonic Mia 2 on. Gently move the brush using a small circular motion across your face. The device features a T-timer that prompts you to move to different areas of your face:
   • 20 aaya lori iwaju
   • 20 seconds on the nose/chin area
   • 10 aaya lori kọọkan ẹrẹkẹ
5. Ṣetọju Olubasọrọ: Ensure the brush head remains flush against your skin. The outer bristles are designed to contain any residual mist from the brush oscillation.
6. Tiipa aifọwọyi: The Mia 2 will automatically shut off after one minute, indicating the completion of a full cleansing cycle.

5.1 Eto iyara

The Clarisonic Mia 2 offers two speed settings for personalized cleansing. Press the power button to cycle through the available speeds. The device will remember your last used speed setting for the next use.

6. Itọju

6.1 Ninu ẹrọ naa

After each use, rinse the brush head and the device handle with warm water. Ensure no cleanser residue remains. Allow the device to air dry completely before storing.

6.2 Rírọ́pò Orí Fọ́

For optimal performance and hygiene, it is recommended to replace your Clarisonic brush head every three months. To replace, twist the old brush head counter-clockwise and pull it off. Align the new brush head with the device and twist clockwise until it locks into place.

7. Laasigbotitusita

If you encounter issues with your Clarisonic Mia 2, refer to the following common solutions:

• Ẹrọ Ko Tii: Ensure the device is fully charged. Connect it to the charger for at least 18 hours for a complete charge.
• Ohun elo Ko Ngba agbara: Verify that the charger is properly connected to a power outlet and that the device is correctly seated on the magnetic charging cradle. Check for any debris on the charging contacts of both the device and the charger.
• Reduced Performance/Vibration: This may indicate a low battery. Recharge the device. If the issue persists, the brush head might be worn out and require replacement.
• Sisun omi: While the device is designed to be water-resistant, ensure the brush head is securely attached. Avoid submerging the entire device in water for extended periods. If water ingress is suspected, discontinue use and contact customer support.

For further assistance, please contact Clarisonic customer support.

8. Awọn pato

9. Atilẹyin ọja ati Support

For information regarding product warranty, please refer to the documentation included with your purchase or visit the official Clarisonic website. For technical support, replacement parts, or any other inquiries, please contact Clarisonic customer service.

O le wa alaye diẹ sii ati awọn orisun atilẹyin nipasẹ lilo si Clarisonic Brand Store.

10. Ìjẹ́rìísí Ìjẹ́rìísí

To ensure you have a genuine Clarisonic product, check for the anti-fake label on the seals of the packaging. A genuine product will have an intact anti-fake label. If the label is scrapped off, the product may be used. If there is no label, the product may be counterfeit.