WIRELESS CONTROLLER H510/H511 USER MANUAL Please visit sunwaytek.com for updates and support. Scan to view video guides on…
Wireless game controller for
PS-4/PS-4 Slim/PS-4 Pro/PC
The first time you use the controller, or when you want to use the controller on another PS-41PS-4 Slim/PS-4 ProtPC system. you must perform device registration (pairing). Turn on my P5-4 system and connect the controller to the system with the USB cable to complete device registration After the first successful pairing, a one-button connecting mode for ease of handling.
Wired pairing method:
Connect the controller with the PS-4 console via MiCro-USB cable to complete the pairing then you can enjoy your games.
Wireless pairing method:
In the Sleep state of the controller, press the SHARE button. then press the HOME button for about 3 seconds, observe the LEO Bar Starts flashing twice at the white light interval, it enters the wireless pairing mode, then you can search the devices that support the PS-4 controller by Blutooth.
Connect the PS-4 controller to the MAC computer:
The computer enters the system preferences – Bluetooth – turn on Bluetooth (if your Bluetooth is turned on, you need to turn oil the device, then press and hold the power button, about 5-10 seconds, the Bluetooth device indicator flashes and starts. Indicating that the Bluetooth pairing state has been entered), hold down the SHARE button of the PS-4 controller and press the HOME button for about 3-5 seconds at the same time, When the indicator light bar flashes white, release the button (the painting mode cannot be entered during charging) you will see the controller can be paired on the device, click on the painting and it will connect successfully after a while
Connect the controller to the PC console.
Please instill the USS Bluetooth controller receiver (Not included) into the PC, the PC will automatically install the driver On the device, find console – device, and printer – add device – click Next, then you will see the Wireless Controller, click next to the computer automatically installs the driver. At this time, the PS-4 light bar wins diSplay white tight, indicating that it has been paired with the computer and can be used.
Turn oft the controller/disconnect Press the key Combination:
LI +RI +PS buttons, long press for 5-7 seconds. until the light bar of the controller goes out
|Operating voltage||DC 1 7V-4 2V|
|USB input voltage/current||DC 5V |
|Available distance||≤ 8m|
|Battery power-on time||Around 10-12h (fully charged)|
|Net weight||about 209g|
|US8 cable Length||Amoco( 59.05 inches**|
|Packing list||1* Controller + l* charging cabin + 1*User guide|
Remark: The above parameters are for references only, they are subject to the actual product.
For support or General help questions please contact
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction
|YCCTEAM YCC-PS6003 Wireless Game Controller [pdf] Instruction Manual|
YCC-PS6003, YCCPS6003, 2A5DUYCC-PS6003, 2A5DUYCCPS6003, YCC-PS6003 Wireless Game Controller, Wireless Game Controller
PANDOOKS PANDOOKS I18 True Wireless Earbuds Bluetooth Earphone SPECIFICATION BRAND PANDOOKS MODEL NUMBER i18 COLOR…
AD409-Pro Digital Microscope Digital Microscope AD409-Pro Users Manual Thank you for purchasing our products! To…
2769-20 M18 FUEL 1/2 Inches Extended Anvil Controlled Torque I OPERATOR'S MANUAL MANUEL de L'UTILISATEUR…
BKA-PLUS Power Amplifier PLUS SPEAKER LEVEL OUTPUT
BP333Plus Tape Dispensing Machine USER MANUAL BP333+ REV 2 10072022 This manual is a non-controlled…