Xprite DL-001-L3-W LED Truck Bed Light
INTRODUCTION
The Xprite DL-001-L3-W LED Truck Bed Light is a useful way to light up your truck bed, giving you sufficient light for a range of chores. This LED light, which only costs $19.99, is great for people who want to make their truck safer and easier to see, especially when they are loading or unloading at night. The light can be used outside because it has an IP67 grade, which means it is waterproof and will last in any weather. With 2835 SMD LED chips and three LEDs per pod, the light gives off a bright, clear white light at an impressive 0.5W per LED. On November 13, 2015, Xprite released this product for the first time. Truck owners still like it a lot. This light is a great addition to any truck bed because it’s reliable and easy to install. You’ll never be in the dark again.
SPECIFICATIONS
| Brand | Xprite |
| Price | $19.99 |
| Auto Part Position | Inside |
| Water Resistance Level | Waterproof |
| Manufacturer | Xprite |
| Voltage | 12V |
| LED Chip | 2835 SMD |
| Chips | 3 LEDs per pod |
| Power per LED | 0.5W |
| Rated Power | 1.5W |
| Waterproof Rating | IP67 |
| Item Weight | 8.1 ounces |
| Product Dimensions (L x W x H) | 8 x 5 x 2 inches |
| Item Model Number | DL-001-L3-W |
| Date First Available | November 13, 2015 |
WHAT’S IN THE BOX
- Truck Bed Light
- User Guide
FEATURES
- High Brightness: The system has 8 pods, and each one has 3 ultra-bright SMD LEDs, for a total of 24 LEDs that give off the most light.
- Long Power line: There is a 21-foot power line on each strand, which is plenty of length to connect to a power source and a switch.
- Waterproof and Weatherproof: The lights have an IP67 rating, which means they are waterproof, shockproof, and made to last in bad weather like snow and rain.
- Flexible Mounting Options: The pods can be attached using either 3M adhesive or screws, so the mounting can be done in any way that works best for you.
- Flexible Use: It can be used in a lot of different places, like truck beds, rock lights, under-car lighting, footwells, and more.
- Energy-Efficient: Each pod only uses 1.5W of power, so the system is energy-efficient while still giving off enough light.
- Customizable Setup: The flexible connectors between each pod make it possible to install them in a way that fits your needs, even in small areas.
- Small Size: Each pod is small and light, so it won’t take up too much room in the truck bed or other places where it needs to be installed.
- Strong Construction: The pods are shockproof and made to handle the bumps and shocks that you might find off-road or in rough places.
- Wide Voltage Compatibility: The system works with a 12V power source, so it can be used in a lot of different cars, like trucks, SUVs, ATVs, and boats.
- Easy to Use: It has an on/off switch that makes it simple to manage the light pods from inside your car.
- Aesthetic Improvement: The lights make your truck bed or other surfaces look better by adding a stylish touch that looks good day or night.
- Easy to Set Up: The system comes with all the tools you need to set it up, like 3M glue, screws, and a clear setup guide.
- Universal Fit: This means it can be used on most cars, like trucks, RVs, SUVs, motorcycles, and more.
SETUP GUIDE
- Figure Out Where to Install: Pick a good spot in your truck bed, like along the rails or in the wheel wells, where the pods will give off the most light.
- Clean Installation Surface: To make sure the pods stick well, make sure the surface where you will be putting them is clean and free of oil, dirt, and water.
- Check the Length of the Power Wire: Check the 21-foot power wire to make sure it’s long enough to reach the switch and the power source in your car.
- Plan Where to Put Each Pod: Use the two feet of wire that are between each pod to figure out where to put each light pod along the area where you want to install them.
- Test the System: Before installing the system, make sure the LED pods work by plugging them into a power source and testing them.
- Use 3M Adhesive or Screws: Use 3M adhesive strips to attach each pod for easy setup, or use screws for a more secure fit.
- Route the Power Wire: Carefully route the power wire to the truck’s power source, making sure it doesn’t get broken or get in the way of moving parts.
- Install the On/Off Switch: Put the on/off switch somewhere in the cab that is easy to get to, like near the dashboard or center panel.
- Connect the Power Wire: Once the pods are in place, connect the power wire to the 12V power source in the car. This can be done by connecting the wire directly to the battery or through a fuse box.
- Secure Wires: To keep the power wire along the inside of the car from moving around, use zip ties or adhesive clips to hold it in place.
- Final Testing: Turn on the system to make sure all of the pods work and the switch works as it should.
- Change the Light Angle: If you need to, you can change the angle of the pods to get the lighting effect you want.
- Check for Interference: Make sure that the wiring doesn’t mess up any other parts of the car or cause any electricity problems.
- Waterproofing Check: Make sure the waterproof seal on the pods and wires is tight so water doesn’t get in and damage the system.
- Enjoy the Light: Once the installation is done, you can enjoy the bright, energy-efficient lighting that makes your car look better and work better.
CARE & MAINTENANCE
- Cleaning Often: Use a soft cloth and a mild cleaning solution to wipe down the pods and wires often to get rid of dust, dirt, and grime.
- Look for Damage: Check the lights every so often for any signs of physical damage, like cracks or loose wires, and fix or replace them as needed.
- Check for Moisture: To make sure the pods stay waterproof, look inside to see if any water has collected. If you find any wetness, dry them right away.
- Not Getting Too Hot: Make sure the power source and wires are not getting too hot, as this could damage the system.
- Tighten the mounting screws: Screws may become loose over time because of vibrations, so check and tighten them every so often to make sure the fastening is secure.
- Check the Wire Connections: Check the wire connections to make sure they are tight and free of corrosion or wear, especially if they have been used in hard conditions for a long time.
- As needed, replace broken LEDs: If an LED pod stops working, check the link and replace the broken pod or LED chips.
- Store During the Winter: If you live in a place where winters are cold, you might want to take the lights down or cover them up to keep them from getting damaged.
- Monitor Power Source: To avoid any electrical problems, make sure that the vehicle’s 12V power source is working properly and that the voltage stays solid.
- Keep them from getting too much UV light: If you put the lights somewhere that get some shade, they won’t be in full sunlight for too long, which can fade the colors or wear them down.
- Check the Adhesive’s Integrity: If you’re using 3M adhesive, make sure the adhesive is still holding the pods tightly every so often. If it starts to break down, replace it.
- Use Tools That Don’t Scratch: When you clean or fix the lights, don’t use rough materials or strong chemicals that could scratch the pods’ surface.
- Test Functionality: Make sure all parts are working properly by testing the on/off switch and each pod on a regular basis.
- Protect wire: If the wire is going to be exposed to the weather, put protective sleeves or covers on it to keep it from getting worn down.
- Replace Parts as Needed: If any part of the system, like a pod or switch, starts to break down, you should replace it right away to keep the whole thing working.
TROUBLESHOOTING
| Problem | Possible Cause | Solution |
|---|---|---|
| Light not turning on | Loose connection or faulty wiring | Check all connections and ensure wiring is properly installed. |
| Light is dim | Insufficient power supply | Verify that the voltage is within the correct range (12V). |
| Flickering light | Voltage fluctuations or unstable power supply | Install a voltage regulator to ensure a stable connection. |
| Water ingress | Sealant failure or improper installation | Inspect the light for damage and reseal if necessary. |
| Poor light output | Dirt or debris on the light | Clean the light surface and ensure the lens is clear. |
| Not responding to switch | Faulty switch or loose wiring | Check the switch connection and replace if necessary. |
| Inconsistent lighting | Bad connection between LEDs and power source | Recheck wiring and LED connections for faults. |
| Overheating | Prolonged use or poor ventilation | Turn off the light and allow it to cool. Ensure proper airflow. |
| Light bar not fitting | Incorrect installation or incompatible mounting area | Check compatibility with your truck and adjust as needed. |
| Corroded connectors | Exposure to harsh weather or road salt | Clean connectors and apply a protective sealant to prevent further corrosion. |
PROS & CONS
PROS:
- Affordable price at $19.99, offering great value for the features.
- Waterproof (IP67 rating), suitable for all weather conditions.
- 2835 SMD LED chips provide bright and efficient illumination.
- Easy installation process for a quick setup.
- Compact design (8 x 5 x 2 inches) that fits easily in truck beds.
CONS:
- Limited to inside truck bed usage, not versatile for exterior lighting.
- A rated power of 1.5W may not be as bright as higher-powered alternatives.
- Shorter cable length could limit placement options for some trucks.
- The LEDs might not cover a large truck bed for full illumination.
- Not adjustable—no ability to direct light to specific areas.
WARRANTY
The Xprite DL-001-L3-W LED Truck Bed Light is backed by a 1-year limited warranty. This warranty covers any defects in material or workmanship under normal usage. However, the warranty does not apply to damage caused by misuse, improper installation, or accidental damage. To make a warranty claim, ensure you have your proof of purchase and contact Xprite’s customer service team.
FREQUENTLY ASKED QUESTIONS
What is the price of the Xprite DL-001-L3-W LED Truck Bed Light?
The Xprite DL-001-L3-W LED Truck Bed Light is priced at $19.99, offering an affordable solution to illuminate your truck bed.
What is the voltage of the Xprite DL-001-L3-W LED Truck Bed Light?
The Xprite DL-001-L3-W LED Truck Bed Light operates at a 12V voltage, making it compatible with most vehicles.
What is the water resistance level of the Xprite DL-001-L3-W LED Truck Bed Light?
The Xprite DL-001-L3-W LED Truck Bed Light has an IP67 waterproof rating, ensuring it is fully protected against dust and submersion in water.
How many LEDs are there per pod in the Xprite DL-001-L3-W LED Truck Bed Light?
The Xprite DL-001-L3-W LED Truck Bed Light features 3 LEDs per pod, providing bright and even illumination.
What is the rated power of the Xprite DL-001-L3-W LED Truck Bed Light?
The Xprite DL-001-L3-W LED Truck Bed Light has a rated power of 1.5W per pod, ensuring efficient energy use.
What is the chip type used in the Xprite DL-001-L3-W LED Truck Bed Light?
The Xprite DL-001-L3-W LED Truck Bed Light uses 2835 SMD LED chips, known for their energy efficiency and bright light output.
What are the dimensions of the Xprite DL-001-L3-W LED Truck Bed Light?
The Xprite DL-001-L3-W LED Truck Bed Light measures 8 x 5 x 2 inches, making it compact enough to fit inside your truck bed.
What is the weight of the Xprite DL-001-L3-W LED Truck Bed Light?
The Xprite DL-001-L3-W LED Truck Bed Light weighs 8.1 ounces, making it lightweight and easy to install.