ME4000R Range Microwave Oven
ufakelo Imiyalelo
Ngaphezulu kwesitovu seMicrowave
BEFORE YOU BEGIN (Read these instructions completely and carefully.)
IMPORTANT Save these instructions for local inspector’s use.
IMPORTANT Observe all governing codes and ordinances.
· Note to Installer
– Qinisekisa ukuyishiya le miyalelo kuMthengi.
· Note to Consumer – Keep these instructions for future reference.
· Skill level
– Installation of this appliance requires basic mechanical and electrical skills.
· Ufakelo olufanelekileyo luxanduva lwesifaki.
· Ukungaphumeleli kwemveliso ngenxa yofakelo olungalunganga ayihlanganiswa phantsi kweWaranti.
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 1
2021-03-25 11:46:26
Contents
ulwazi ngokubanzi
Important safety instructions . . . . . . . . . . . 3 Electrical requirements. . . . . . . . . . . . . . . . 3 Hood exhaust . . . . . . . . . . . . . . . . . . . . . . . . 4 Damage – Shipment/Installation . . . . . . . . 6 Parts included . . . . . . . . . . . . . . . . . . . . . . . 6 Tools you will need . . . . . . . . . . . . . . . . . . . 7 Mounting space . . . . . . . . . . . . . . . . . . . . . . 7
Step-by-step installation guide
1. Placement of the mounting plate. . . . . . 8
A. Removing the microwave oven from the carton/removing the mounting plate . . . . 8
B. Finding the wall studs . . . . . . . . . . . . . . . . 8 C. Determining wall plate location under your
cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 D. Aligning the wall plate . . . . . . . . . . . . . . . 10
2. Ventilation types (choose a, b or c) . . . 11
A. Outside top exhaust (vertical duct) . . . . 12 A1. Installation procedure for exhaust adaptor and proper damper operation check . . . . . . . . . . . . . . . . . . . . . . . . . . 12 A2. Adjust the exhaust adaptor . . . . . . . . 12
B. Recirculating (non-vented ductless). . . . 12 B1. Adapting microwave blower for recirculation . . . . . . . . . . . . . . . . . . . . . 12 B2. Installing the charcoal filter. . . . . . . . . 13
C. Outside back exhaust (horizontal duct) . 14 C1. Adapting microwave blower for outside back exhaust . . . . . . . . . . . . . . . . . . . . 14
3. Installation . . . . . . . . . . . . . . . . . . . . . . . 15
A. Preparing the rear wall for outside back exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Attach the mounting plate to the wall . . 15 C. Use top cabinet template for preparation of
top cabinet. . . . . . . . . . . . . . . . . . . . . . . . 16 D. Mount the microwave oven . . . . . . . . . . 16 E. Connecting ductwork for outside top
exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Before you use your microwave . . . . . . . 18
2
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 2
2021-03-25 11:46:26
ulwazi ngokubanzi
IMIYALELO YOKHUSELEKO EBALULEKILEYO
This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury.
CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 59 pound product, plus additional oven loads of up to 50 pounds or a total weight of 109 pounds.
CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.
NOTE: For easier installation and personal safety, it is recommended that two people install this pIrnosudreucprto.per
groundexists
IMbePfoOreRusTeANTPLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.
InsurIgenrsopuurrneodpperexoiprsetsr grounbedfoerexuisstes before use.
Intambo yombane yale sixhobo ixhotyiswe ngeplagi (yomhlaba) eplagiweyo edibana nesilinganisi esine-prong (grounding) esisezantsi sodonga ukunciphisa ukubakho kwengozi yomothuko yombane kwesi sixhobo.
Kuya kufuneka ukuba isamkeli sedonga kunye nesekethe ihlolwe ngumbane oqeqeshiweyo ukuze aqiniseke ukuba isitya sisekwe ngokufanelekileyo.
Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.
SUKUYENZE, NGAPHANTSI KWAZO ZONKE IIMEKO, SIKA, ULAWULEKILE OKANYE UKUSUSA NAYIPHI NA IPRONG YAMANDLA. SUKUYISETYENZISWA NGENTLU YOKWANDISA
IIMFUNO ZOMBANE
Ukulinganiswa kwemveliso yi-120 volts AC, 60 Hertz, 13 ampLe mveliso kufuneka iqhagamshelwe kwisekethe yokubonelela yevol efanelekileyotage kunye nobuninzi. Ubungakanani bocingo kufuneka luhambelane neemfuno zeKhowudi yoMbane kaZwelonke okanye ikhowudi yengingqi ekhoyo kulo mlinganiselo wekhilowathi. Intambo yokuhambisa umbane kunye neplagi kufuneka maziswe kwisekethe eyahlukileyo yesiseko esinye esine-15 A kunye nobuninzi be-20 A. Ibhokisi yokuphuma kufuneka ibekwe kwikhabhinethi ngaphezulu kwe-oveni ye-microwave. Ibhokisi yokuphuma kunye nesekethe yokubonelela kufuneka ifakwe ngumbane oqeqeshiweyo kwaye ihambelane neKhowudi yoMbane yeSizwe okanye ikhowudi yendawo ekhoyo.
3
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 3
2021-03-25 11:46:26
ulwazi ngokubanzi
UKUKHATHAZA KWEZINTO
QAPHELA: Funda la maphepha mabini alandelayo kuphela ukuba uceba ukukhuphela umbhobho wakho ngaphandle. Ukuba uceba ukubuyisela umoya kwakhona kwigumbi, qhubeka kwiphepha le-11.
UKUPHATHA NGAPHAKATHI KWE-TOPAMPKUPHELA)
Itshathi elandelayo iqulethe i-exampufakelo olunye olunokubakho lwendlela.
IIPHEPHA ZOKUGQIBELA
UBUDE OBULINGANA
x
KUSETYENZISIWE AMANANI
=
UBUDE OBULINGANA
Cap yophahla
I-24 ft.
x
(1)
=
I-24 ft.
12 Ft. Straight Duct (6 Round)
I-12 ft.
x
(1)
=
I-12 ft.
I-Rectangular-to-Round Transform Adapter *
I-5 ft.
x
(1)
=
I-5 ft.
Ubude obulinganayo beziqwenga zendlela zisekwe kuvavanyo lokwenyani kwaye zibonisa iimfuno zomsebenzi olungileyo wokungena nangayo nayiphi na indawo yokuhamba.
Total Length =
I-41 ft.
KUBALULEKILEYO: Ukuba iadaptha yoguqulo oluxande ukuya kumjikelo lusetyenziswa, iikona ezisezantsi ze-damper kuya kufuneka isikwe ukuze ilingane, kusetyenziswa i-tin snips, ukwenzela ukuvumela intshukumo ekhululekileyo ye-d.ampi-er.
UKUPHATHA NGAPHANDLE NGOKUQHELEKILEYO (EXAMPKUPHELA)
Itshathi elandelayo iqulethe i-exampufakelo olunye olunokubakho lwendlela.
IIPHEPHA ZOKUGQIBELA
UBUDE OBULINGANAYO *
x
KUSETYENZISIWE AMANANI
=
UBUDE OBULINGANA
Ikapa yoDonga
I-40 ft.
x
(1)
=
I-40 ft.
3 Ft. Straight Duct (3 ¼ x 10 Rectangular)
I-3 ft.
x
(1)
=
I-3 ft.
Ingqiniba engama-90 °
I-10 ft.
x
(2)
=
I-20 ft.
Ubude obulinganayo beziqwenga zendlela zisekwe kuvavanyo lokwenyani kwaye zibonisa iimfuno zomsebenzi olungileyo wokungena nangayo nayiphi na indawo yokuhamba.
Total Length =
I-63 ft.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.
4
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 4
2021-03-25 11:46:26
ulwazi ngokubanzi
NOTE: If you need to install ducts, note that the total duct length of 3 ¼ x 10 rectangular or 6 diameter round duct should not exceed 140 equivalent feet.
Ngaphandle komoya kufuna i-HOOD EXHAUST DUCT. Funda oku kulandelayo ngononophelo.
NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampbajiwuzisa ngokukhululekileyo kwaye akukho nto ivala imibhobho.
Uqhagamshelo Exhaust:
The hood exhaust has been designed to mate with a standard 3 ¼ x 10 rectangular duct.
If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6 diameter duct.
Ubuninzi beendlela:
For satisfactory air movement, the total duct length of 3 ¼ x 10 rectangular or 6 diameter round duct should not exceed 140 equivalent feet.
Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow and are
equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts.
IIPHEPHA ZOKUGQIBELA
UBUDE OBULINGANA
x
KUSETYENZISIWE AMANANI
=
UBUDE OBULINGANA
I-Rectangular-to-Round Transform Adapter *
I-5 ft.
x
() U
=
ft.
Ikapa yoDonga
I-40 ft.
x
() U
=
ft.
Ingqiniba engama-90 °
I-10 ft.
x
() U
=
ft.
Ingqiniba engama-45 °
I-5 ft.
x
() U
=
ft.
Ingqiniba engama-90 °
I-25 ft.
x
() U
=
ft.
Ingqiniba engama-45 °
I-5 ft.
x
() U
=
ft.
Cap yophahla
I-24 ft.
x
() U
=
ft.
Straight Duct 6 Round or 3 ¼ x 10 Rectangular
I-1 ft.
x
* IMPORTANT: If a rectangular-toround transition adaptor is used, the bottom corners of the damper kuya kufuneka isikwe ukuze ilingane, kusetyenziswa i-tin snips, ukwenzela ukuvumela intshukumo ekhululekileyo ye-d.ampi-er.
() U
=
ft.
Total Ductwork =
ft.
Ubude obulinganayo beziqwenga zendlela zisekwe kuvavanyo lokwenyani kwaye zibonisa iimfuno zomsebenzi olungileyo wokungena nangayo nayiphi na indawo yokuhamba.
5
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 5
2021-03-25 11:46:26
ulwazi ngokubanzi
UMONAKALO-UKUTHUNYELWA / UKUFAKWA
· If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. · If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. · If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by
ulungiselelo phakathi komthengi kunye nomfaki.
AMACANDELO ABANDAKANYIWEYO
IPHAKILE YEKHAYA
INXALENYE
QUANTITY
Wood Screws (¼ x 2)
1
Guqula iibholiti
(and wing nuts)
2
(3/16 x 3)
Self-aligning Machine Screws (¼ – 28 x 3 ¼)
2
AMACANDELO OWONGEZA
TOP CABINET TEMPLATE
PART Top Cabinet Template
UMGANGATHO 1
REAR WALL TEMPLATE
Itemplate yeDonga yangasemva
1
ufakelo Imiyalelo
1
Uya kufumana i-hardware yokufakela equlethwe kwipakethi eneyunithi. Khangela ukuqinisekisa ukuba unawo onke la malungu.
NOTE: Some extra parts are included.
Amacebo okucoca ngeGrisi apakishwe ngokwahlukeneyo
2
Khupha iadaptha
1
6
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 6
2021-03-25 11:46:26
IZIXHOBO KUYA KUFUNEKA
ulwazi ngokubanzi
#1 and #2 Phillips screwdriver
Ipensela
Ruler or tape measure and Carpenter square (optional) straight edge
I-Tin snips (yokusika dampyi,
if required)
Scissors (to cut template,
if necessary)
Electric drill with 3/16, ½ and drill bits
Ukucoca iibhloko okanye iziqwenga zomthi, ukuba ziyafuneka kwisithuba sekhabhathi ephezulu (esetyenziselwa ufakelo lwekhabhathi olungaphantsi kuphela)
iiglavu
I-Saw (i-saber, umgodi okanye i-keyhole)
Stud finder or Hammer (optional)
Imigudu yokhuseleko
Nqanaba
I-Duct kunye ne-masking tape
ISITHUBA EPHAKAMILEYO
12 ubuninzi.
16 ² 30 5
I-30 imiz.
Bottom edge of cabinet needs to be 30 or more from the cooking surface.
I-Backsplash
AMAZISO:
· The space between the cabinets must be 30 wide and free of obstructions.
· This microwave oven is for installation over ranges up to 36 wide.
· If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for exhaust duct preparation.
· When installing the microwave oven beneath smooth flat cabinets be careful to follow the instructions on the top cabinet template for power cord clearance.
· Maximum cabinet depth above and beside the unit is 12.
· The dimensions provided are the minimum required for mounting the microwave oven. Local codes and practical use of the range will likely require more than 13.5 shown between the range and the bottom of the microwave.
7
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 7
2021-03-25 11:46:27
Step-by-step installation guide
1. UKUBEKWA KWEPLATE YOKUFAKA
A. UKUSUSA I-microwave OVEN EBHODWENI / UKUSUSA IBHODI EPHAKAMILEYO
1. Remove the installation instructions, Exhaust adaptor, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven.
2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
CCaarrtotnon
StyroSftoyraofmoam
3. Pull the carton up and off the oven. 4. Remove and properly discard plastic bags.
SSccrewwss
SSccrewwss
MMoouunntiinnggPPlalteate
B. UKUFUMANA IINDAWO ZOKUDALA
WWaallllSStuuddss
CeCnetnetrer
1. Find the studs, using one of the following methods: A. Stud findera magnetic device which locates nails. OR B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location.
2. After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should be 16 or 24 from this mark.
3. Draw a line down the center of the studs. THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.
5. Remove the 2 screws from the mounting plate. This plate will be used as the rear wall template and for mounting.
NOTE: You will have to reuse two screws in original loction of outcase after removing mounting plate.
8
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 8
2021-03-25 11:46:27
Step-by-step installation guide
C. UKUQINISEKISA INDAWO YEPLEATE YODONGA PHANTSI KWEKHABHINETHI YAKHO
Plate position beneath flat bottom cabinet
Plate position beneath framed recessed cabinet bottom
16 ²
CL
Ubuncinane i-30
Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom of the cabinet.
Plate position beneath recessed bottom cabinet with front overhang
Draw a line on the back wall equal to the depth of the front overhang.
CL
30 to Cooktop
CL
30 to Cooktop
Draw a vertical line on the wall at the center of the 30 space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom cabinet frame.
Iikhabhathi zakho zinokuba ne-trim yokuhombisa ephazamisana nofakelo lwe-microwave. Susa i-trim yokuhombisa ukufaka i-microwave ngokufanelekileyo kwaye uyenze inqanaba.
IMICROWAVE KUFUNEKA IBE YINQANABA.
Use a level to make sure the cabinet bottom is level. If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level.
1. Measure the inside depth of the front overhang. 2. Draw a horizontal line on the back wall an equal
distance below the cabinet bottom as the inside depth of the front overhang. 3. For this type of installation with front overhang only, align the mounting tabs with this horizontal line, not touching the cabinet bottom as described in Step D.
9
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 9
2021-03-25 11:46:27
Step-by-step installation guide
D. UKULUNGISELELA INDLELA YODONGA
Hole A Horizontal Line Area E
Centerline notches
Draw a Vertical Line on Wall from Center of Top Cabinet
CL
Umngxunya C.
Hole B Horizontal Line
Draw a Horizontal line on wall from bottom of “Rear Wall Template”.
ISILUMKISO: Nxiba iiglavu ukunqanda ukusika iminwe kwincam ebukhali.
1. Draw a Vertical line on the wall at the center of the 30 wide space.
2. Draw a Horizontal line on the wall at the bottom of “Rear Wall Template”.
3. Drill holes for toggle bolts on 3 locations (Hole A, Hole B, Hole C) but if the location of hole is same as that of stud, drill a 3/16 hole for wood screw. In other words, toggle bolt can not be used to the location of stud.
QAPHELA: SUKULINGA INTLABATHI NGELI XESHA.
NOTE: Holes A, B and C are inside area E. If none
of A, B and C is in a stud, find a stud somewhere
in area E and draw a forth circle to line up with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside.
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 10
10
2021-03-25 11:46:28
Step-by-step installation guide
2. IINTLOBO ZOKUPHUMELA komoya (KHETHA A, B OKANYE C)
I-oveni ye-microwave yenzelwe ukulungelelanisa ezi ntlobo zintathu zokungenisa umoya:
A. Outside Top Exhaust (Vertical Duct) B. Recirculating (Non-Vented Ductless) C. Outside Back Exhaust (Horizontal Duct)
NOTE: This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). And exhaust adaptor is shipped assembled to the filler-upper. Select the type of ventilation required for your installation and proceed to that section.
A. UKUPHATHA NGAPHAKATHI KWE-TOP (I-Vertical DUCT)
Adaptor in Place for Outside Top Exhaust
B. UKUHLAZIYWA (OKUNGENZIWEYO OKUNGENZIWEYO)
Jonga iphepha 12
See page 13 A Charcoal Filter Accessory Kit is required for the nonvented exhaust. (See your Owner’s Manual for the kit number.)
C. UKUTSHINTSHA NGAPHANDLE NGOKUQHELEKILEYO (UHLELO OLULUNGILEYO)
Jonga iphepha 14
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 11
11
2021-03-25 11:46:28
Step-by-step installation guide
A. UKUPHATHA NGAPHAKATHI KWE-TOP (I-Vertical DUCT)
A1. INSTALLATION PROCEDURE FOR EXHAUST ADAPTOR AND PROPER DAMPUMSEBENZI WOKUJONGA
Damper
NOTE: The house duct is needed to connect to the exhaust adaptor after installation completion.
House Duct
Blower Plate
Exhaust Adaptor
Back of Retaining Hooks Microwave
Ihovini
1. Slide exhaust adaptor following the instructions show in diagram.
2. Make sure tape securing damper iyasuswa kwaye damper pivots easily before mounting microwave.
· You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.
A2. Lungelelanisa iAdapter yoKhaya
Open the top cabinet and adjust the exhaust adaptor to connect to the house duct.
Damper
Back of Microwave Oven
For Side-toSide Adjustment, Slide the Exhaust Adaptor as Needed
B. UKUHLAZIYWA (OKUNGENZIWEYO OKUNGENZIWEYO)
B1. ADAPTING MICROWAVE BLOWER FOR RECIRCULATION
1. Remove and save screw that holds blower plate to microwave.
2. Lift up the blower plate.
Blower Retaining Screws
Back of Microwave Oven
NOTE: The exhaust adaptor with damper is not needed for recirculating models. You may want to save them for possible future use. 3. Remove screw holds blower mortor and carefully pull
out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 12
CAUTION: Do not touch blade of blower for preventing crack and break. Hold outer case when the blower pull out or back into.
12
2021-03-25 11:46:28
Step-by-step installation guide
4. Roll the blower unit 90 ° so that fan blade openings are facing toward the front of the microwave.
Before Roll
Emva koLuhlu
8. Secure the blower to the microwave using the blower retaining screws from Step 1.
Blower Retaining Screw
Blower Retaining Screws
5. Place the blower unit back into the opening.
CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. 6. Remove the metal vent fan cover on the back of the
microwave by sliding it up.
Back of Microwave Oven
B2. INSTALLING THE CHARCOAL FILTER 1. Remove screws on top of grille using a #1 Phillips
screwdriver. 2. Open the door. 3. Remove the grille. · After push left, Pull the grille straight off.
Icebo lokucoca amalahle
7. Close the blower door. Slide blower shield onto the top of the blower door opening.
4. Install the charcoal filter. When properly installed, the wire mesh of the filter should be visible from the front.
5. Reinstall the grille and the screws.
6. Vala ucango.
Insert mesh-side up
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 13
13
2021-03-25 11:46:29
Step-by-step installation guide
C. UKUTSHINTSHA NGAPHANDLE NGOKUQHELEKILEYO (UHLELO OLULUNGILEYO)
C1. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST
1. Remove and save screw that holds blower Plate to microwave. Blower Retaining Screws
Back of Microwave Oven
2. Open the blower door by lifting it up at the back of the microwave. Remove and save the blower shield on the back of the microwave by sliding it up. Remove and save the metal vent fan cover on the back of the microwave by sliding it up.
3. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. BEFORE: Fan Blade Openings Facing Forward End B
Isiphelo A
CAUTION: Do not touch blade of blower to prevent cracking and breaking. Hold outer case when the blower is removed and re-installed. (On Some model) 4. Remove Parts “A” with tin snips or pliers.
5. Rotate blower unit counterclockwise 180 °.
Phambi kokuba ujikeleze
Emva kokujikeleza
Back of Microwave
Back of Microwave
6. Place the blower unit back into the opening.
EMVA: I-Fan Blade Openings ejongene nomva
Isiphelo A
End B
CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven.
7. Close the blower door. Slide blower shield onto the top of the blower door opening. Secure the blower to the microwave oven using the blower retaining screws from Step 1 except the upper blower motor retaining screw. Blower Retaining Screw Blower Shield
Blower Retaining Screw
Back of Microwave Oven
8. Slide the exhaust adaptor onto the back of the microwave oven, securing it into the lower locking tabs. Take care to ensure that the dampIhenjisi ye-er ifakiwe ukuze ibe phezulu kwaye i-damper swings freely. Reinstall the upper blower motor screw through the adaptor and the blower door and into the back of the microwave oven. Back of Microwave Oven
Parts “A”
Guide Adaptor
Isikhokelo
Locking Tabs (not shown)
Blower Motor Door Retaining Screw
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 14
14
2021-03-25 11:46:29
3. UKUFAKWA
UKUFAKWA KWAKHONAVIEW
A. Prepare Rear Wall (only horizontal duct) B. Attach Mounting Plate to Wall C. Prepare Top Cabinet D. Mount the Microwave Oven E. Connecting Ductwork (only vertical duct)
Step-by-step installation guide
A. UKULUNGISELELA UDONGA LWENGEMVA UKUPHUMA NGAPHANDLE NGAMVA
Kuya kufuneka usike indawo evulekileyo kudonga lwangasemva lwangaphandle.
B. QAPHELA Ipleyiti YOKUFAKA UDONGE
CL
· Read the instructions on the REAR WALL TEMPLATE.
· Tape it to the rear wall. · Cut the opening, following the instructions of the
REAR WALL TEMPLATE. CAUTION: Do not cut an opening on the real wall, in case of vertical duct and non-vented ductless.
Namathisela ipleyiti eludongeni usebenzisa iibholiti ezitshintshayo. Ubuncinci kufuneka kusetyenziswe isikrufu somthi ukuncamathisela ipleyiti kudonga lwesidonga.
1. Remove the toggle wings from the bolts. 2. Insert the bolts into the mounting plate through the
holes designated to go into drywall and reattach the toggle wings to ¾ onto each bolt.
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 15
15
2021-03-25 11:46:29
Step-by-step installation guide
Ukusebenzisa iibholiti zokuguqula:
MoMuonutnintingg PlaPtelate
SSppaacciinnggfofroTroTgoglgesglMeosreMore TThhaann WWaallllTThihckicnkesnsess
TooggggleleWWinignsgs TTooggggllee BBooltt
WWalll
BBoolltt Enndd
3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw, make sure to coincide bottom line of the Mounting plate with Horizontal line of “Rear wall Template” and then the Mounting plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.
4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.
C. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
Kuya kufuneka ubole imingxunya kwizikulufu zenkxaso ephezulu kunye nomngxunya omkhulu ngokwaneleyo ukuze intambo yombane ilingane.
D. FAKA I-Oveni yemayikhrowave
FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: Filler blocks are required when mounting this unit under any cabinet with a recessed bottom or front overhang. (See page 9.) IMPORTANT: The case damage that will occur from over tightening screws when filler blocks are not used is not covered under warranty. NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 13. Do not pinch cord or lift oven by pulling cord.
1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.
· Read the instructions on the TOP CABINET TEMPLATE.
· Tape it underneath the top cabinet.
· Drill the holes, following the instructions on the TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.
2. Rotate front of oven up against cabinet bottom.
3. Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 16
16
2021-03-25 11:46:30
Step-by-step installation guide
CaCbabiinneettFFrornot nt CCaabbinienteBtotBtoomtStohemlf Shelf FFiillleerrBlBoclkock
EEqquuivaivleanltetont to DDeeppthtohf of Cabinet CRaebcineetsRsecess
SSeelf-lAf-liAgnliinggnSicnregwScrew
MicMricorowwaavveeOOvevneTonp Top
4. Attach the microwave oven to the top cabinet. 5. Insert the 2 self-aligning screws through the cabinet
bottom shelf and filler block into the outer top cabinet of the unit. Continue to support the unit until both screws are inserted and engaged at least two full turns, then fully tighten both screws until the unit is secure.
E. CONNECTING DUCTWORK FOR OUTSIDE TOP EXHAUST
House Duct
1. Extend the house duct down to connect to the exhaust adaptor.
2. Seal exhaust duct joints using duct tape.
6. Install grease filters. See the Owner’s Manual packed with the microwave.
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 17
17
2021-03-25 11:46:30
Before You Use Your Microwave
NGAPHAMBI KOKUSEBENZISA I-microbewave yakho
1. Make sure the microwave oven has been installed according to instructions.
6. Read the Owner’s Manual.
2. Remove all packing material from the microwave oven.
3. Install turntable and ring in cavity.
4. Replace house fuse or turn breaker back on.
7. Keep installation instructions for the local inspector’s use.
5. Plug power cord into a dedicated 15 amp indawo yokuphuma yombane.
IgbnreIsnofusouurrnereedIgbnpreuspoefurousrxorroneeedippspueeetrsrxoseripsetsr groundexists beforeuse
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 18
18
2021-03-25 11:46:30
Phawula
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 19
19
2021-03-25 11:46:30
ME4000R_ME17R7021EB_AA_DE68-04584A-01_EN.indd 20
I-DE68-04584A-01
2021-03-25 11:46:30
Amaxwebhu / Izibonelelo
 |
SAMSUNG ME4000R Range Microwave Oven [pdf] Isikhokelo sokuFakelo ME4000R Range Microwave Oven, ME4000R, Range Microwave Oven |
