UKUFAKELWA & NENKONZO
LOGIC MAX COMBI2
C24 C30 C35

Ideal C24 Logic Max Combi2

Xa utshintshela kuyo nayiphi na indawo kwesi sixhobo, sebenzisa kuphela iindawo ezisecaleni onokuthi uqinisekiswe ukuba ziyahambelana neenkcukacha zokhuseleko kunye nokusebenza esikufunayo. Musa ukusebenzisa iinxalenye ezihlaziyiweyo okanye zokukhuphela ezingagunyaziswanga ngokucacileyo nguKufudumeza okuKufanelekileyo. Ukufumana ikopi yamva nje yoncwadi lwengcaciso kunye nezenzo zokulondolozwa ndwendwela yethu webindawo idealheating.com apho unokukhuphela ulwazi olufanelekileyo kwifomathi yePDF.
NgoJulayi 2022
I-UIN 228290 A05

IDATHA yeERP

			UMZEKELO
	UMFANEKISO	IIUNITHI	24 kW	30 kW	35 kW
I-Boiler yokuqinisa	n / A	n / A	Ewe	Ewe	Ewe
Ibhoyila yobushushu obuphantsi	n / A	n / A	Hayi	Hayi	Hayi
B1 Ibhoyila	n / A	n / A	Hayi	Hayi	Hayi
I-Cogeneration Space heater	n / A	n / A	Hayi	Hayi	Hayi
Ixhotyiswe ngesifudumezi esongezelelweyo	n / A	n / A	Hayi	Hayi	Hayi
Iheater edibeneyo	n / A	n / A	Ewe	Ewe	Ewe
IsiPhumo soBubushushu esisiSithuba sokuFundisa kwiSithuba
Umthwalo opheleleyo	P4	kW	24.3	24.3	24.3
Inxalenye yomthwalo	P1	kW	8	8	8
Ukusetyenziswa koMbane oNcedisayo
Umthwalo opheleleyo	elmax	kW	0.044	0.028	0.028
Inxalenye yomthwalo	Elmin	kW	0.013	0.009	0.026
Yima ecaleni kuka	PSB	kW	0.002	0.003	0.002
Ixesha loNyaka lokuFundisa ngokuSebenzayo kwamandla
Umthwalo opheleleyo	q4	%	90	90	90
Inxalenye yomthwalo	ni	%	98.6	98.6	98.6
Ilahleko yokulinda	Pstby	kW	0.05	0.05	0.05
Umlilo	I-Pig	kW	0	0	0
Ukukhutshwa kwe-NOx (Gross)	NOx, ichibi Hs	mg/kWh	28	25	30
UkuSetyenziswa kwamandla ngoNyaka	ORE	GJ	75	75	75
INqanaba laMandla oSandi. Ngaphakathi	LWA	dB	50	46	46
Amanzi Ashushu Asekhaya
Amanzi Ashushu Asekhaya	Elec	kWh	0.136	0.133	0.137
Ukufudumeza kwamanzi ngokufanelekileyo (Eco) Ukucofa iProfile L	qW1-1	%	82	81	79
Ukusetyenziswa kwamafutha emihla ngemihla 24hr (GCV)Eyona ilinganisiweyo	Isibaso	kWh	14.7	14.83	15.14
Ukusetyenziswa kombane ngonyaka	I-AEC	kWh	29	28	29
Ukusetyenziswa kwamafutha ngonyaka	AFC	GJ	11	11	11

WEEE Directive 2012/19/EU
Inkunkuma yoMyalelo weSixhobo soMbane kunye ne-Electronic

• Ekupheleni kobomi bemveliso, lahla ukupakishwa kunye nemveliso kwiziko elihambelanayo lokurisayikilishwa.
• Musa ukulahla iyunithi kunye nenkunkuma eqhelekileyo yasekhaya.
• Musa ukutshisa imveliso.
• Susa iibhetri.
• Lahla iibhetri ngokweemfuno zomthetho zengingqi hayi ngenkunkuma eqhelekileyo yasekhaya.

Ikhowudi yokusebenza yofakelo, ugunyaziso kunye nonikezelo lweenkqubo zokufudumeza ezisembindini
IMVELISO FICHE
LOGIC MAX COMBI² C BOILER
Ideal yokufudumeza ERP DATA

	UMFANEKISO	IIUNITHI	UMZEKELO
			24 kW	30 kW	35 kW
Ibhoyila yokujiya			Ewe
Ixesha lonyaka iklasi zokufudumeza ukusebenza kakuhle			A
Ubushushu obulinganiswe ngemveliso		kW	24
Ixesha lonyaka lokufudumeza amandla ngokufanelekileyo	ns	oh)	94*
Ukusetyenziswa kwamandla ngonyaka	QHE	GJ	75
Inqanaba lamandla esandi, ngaphakathi	LWA	dB	50	46	46
Iklasi yokufudumeza kwamandla okusebenza kakuhle kwamanzi			A

ISithuba seSithuba seSithuba sokuSebenza ngokuSebenza kakuhle kwamandla eBoiler								*% 94%	A
Ulawulo lobushushu (ukusuka kwi-fiche yolawulo lobushushu)								%	B
Iklasi I	Iklasi yesi-11	Udidi III	Iklasi IV	Iklasi V	Iklasi VI	Iklasi VII	Iklasi VIII
1%	2%	I-2.%	2%	3%	4%	I-4.%	5%

Umnikelo weSolar (ukusuka kwisixhobo sesola)

Ixesha loNyaka lokuFundisa amandla ngokuSebenzayo kwePhakeji

Ixesha loNyaka leSithuba sokuFundisa ngokuSebenza ngokuLungileyo kwaMandla kwiKlasi yePhakeji

Ukusebenza kwamandla kwepakethi yeemveliso ezibonelelwe kolu xwebhu akunakuhambelana nokusebenza kwayo kwamandla okwenene xa ifakwe kwisakhiwo, njengoko ukusebenza kakuhle kuphenjelelwa yimiba eyongezelelweyo efana nokulahleka kobushushu kwiimveliso ngokunxulumene nobukhulu besakhiwo kunye nesakhiwo sayo. iimpawu.
AMANQAKU OMFAKI
Kuyo nayiphi na imibuzo yobugcisa nceda ucofe umnxeba woncedo wokuFakela: 01482 498663
INKQUBO YOKUQALA KWAKHONA YEBOILER –
Cofa iqhosha lokuQALA kwakhona. Ibhoyila iya kuphinda ulandelelwano lokutshisa ukuba kukho imfuno yobushushu.
IINKCAZELO
ISILUMKISO: Umngcipheko wokwenzakala okanye ukufa
ISILUMKO: Umngcipheko womonakalo kwizinto
EBALULEKILEYO T: Ulwazi olubalulekileyo
Uluhlu lweeAkhronimi

CH - Ubushushu basesiphakathini	IWRAS – iNkqubo yeeNgcebiso ngeMimiselo yaManzi
I-DHW – Amanzi ashushu asekhaya	I-SAP – Inkqubo yoVavanyo oluMgangatho
TRV – Thermostatic Radiator Valve	IEE – Iziko leeNjineli zoMbane
I-PRV – IValve yokuNceda ngoxinzelelo	UKCA – UK Conformity Vavanyiwe
IE - Ayalend	RHS – Ekunene Icala
I-ETCI – Electro-Technical Council of Ireland	LHS – Icala lasekhohlo
BS – uMgangatho waseBritani	PCB – Ibhodi yeSekethe eprintiweyo

Icandelo 1-Jikelele
Itheyibhile yoku-1 yeDatha ngokubanzi

		24 kW	I 30 kW	I 35 kW
Ubonelelo ngerhasi		2H – G20 – 20 mbar
Unxibelelwano lwegesi		15 mm ukunyanzeliswa kobhedu
Ubungakanani be-Injector	mm	4.	5.	mna 4.9
Uqhagamshelo lokungena	Amanzi Abandayo	15 mm ukunyanzeliswa kobhedu
Uqhagamshelo lwe-Outlet	Amanzi Abandayo Ashushu	15 mm ukunyanzeliswa kobhedu
UQhagamshelwano lokuHamba	Ubushushu basesiphakathini	22 mm ukunyanzeliswa kobhedu
Buyisela uQhagamshelwano	Ubushushu basesiphakathini	22 mm ukunyanzeliswa kobhedu
Flue Terminal Diameter	mm	100
I-Avareji ye-Flue Temp-Mass Flow Rate	I-DHW	63°C - 11g/s	68°C - 13g/s	73°C - 15g/s
CO2 Umxholo (± 0.7)	Max. DHW	I-9.%	I-9.%	I-10.%
	Min. CH	I-9.%	I-9.%	I-9.%
Olona xinzelelo luphezulu lokuSebenza (iiNkqubo ezitywiniweyo)	ibha (psi)	2.5 (36.3)
Ubuninzi boxinzelelo lwaManzi ashushu aseKhaya	ibha (psi) [kPa]	Isixhenxe (10.0) [145]
Ubuncinci boxinzelelo lwamanzi ashushu asekhaya*	ibha (psi) [kPa]	0.8(11.6)[80]	1.3(18.9) [130]	Mna 1.3(18.9)**[130]
Ubuncinci be-DHW ye-Inlet yoxinzelelo lokuSebenza kwi-0.6 bar yoxinzelelo lweNkqubo		Zonke Iisayizi zeModeli 0.5 bar
Ubonelelo ngoMbane		230 V - 50 Hz
Ukutya umbane	W	94	93	mna 110
Ukulinganisa iFuse		Ngaphandle : 3 A Ngaphakathi : T4A HRC L250 V
Isiqulatho samanzi	Ilitha yokufudumeza ephakathi (gal)	1.2 (0.26)
	Ilitha yamanzi ashushu asekhaya (gal)	1.0 (0.22)
Ubunzima obupakishweyo	kg	35.	35	35
Phakamisa ubunzima	kg	29.	29.	29.
Ubungakanani beBoiler Casing	Ubude mm	700
	Ububanzi mm	395
	Ubunzulu mm	278

*Iyafuneka ngesantya esiphezulu sokuqukuqela. I-Boiler isebenza phantsi ukuya kwi-2 L / min ukuhanjiswa kwe-DHW
** Kwiindawo zoxinzelelo lwamanzi aphantsi umqobo we-DHW unokususwa
Itheyibhile ye-2 Idatha yokuSebenza - Ukufudumeza okuphakathi

Ukufakwa kweBhola:		Max	Min
			24 kW	30 kW	35 kW
I-Boiler `Q' Net CV I-CV epheleleyo	kW	24.3	4.9	6.1	7.1
	kW	27	5.4	6.7	7.9
Ukusetyenziswa kwegesi	m3/h	2.512	0.5	0.627	0.734
	(ft3/h)	(89)	(18.)	(22)	(26.)
Imveliso yeBhola :
Ayincitshiswanga 70°C iMean iTemp yaManzi.	kW	24.2	4.8	6.1	7.1
Ukunciphisa i-40 ° C iMean Temp yaManzi.	kW	25.6	5.1	6.4	7.5
UFanelo loNyaka* SEDBUK 2005			I-91.%	I-91.%	I-91.%
Ukusebenza kweXesha loNyaka* SEDBUK 2009/2012			89.60%	89.60%	89.60%
NOx Classification		I Class 6

Phawula. Ukusetyenziswa kwerhasi kubalwa kusetyenziswa ixabiso le-calorific le-38.7 MJ/m³ (1038 Btu/ft³ ) gross okanye 34.9 MJ/m³ (935 Btu/ft³ ) nett
Ukufumana ukusetyenziswa kwerhasi ngexabiso elahlukileyo lekhalori:
a. Ngee-l/s – yahlula igalelo lobushushu obugqithisileyo (kW) nge-CV enkulu yerhasi (MJ/m 3)
b. Kwi-Btu/h - phinda-phinda igalelo lobushushu obugqithisileyo (kW) ngo-26.8
c. Ku-ft 3 /h – yahlula igalelo lobushushu obugqithisileyo (Btu/h) nge-CV yerhasi (Btu/ft³ )
d. Kwi-m 3 / h - phinda-phinda i-l/s ngo-3.6
Itheyibhile 3 Idatha yokuSebenza - Amanzi ashushu asekhaya

ElonaNgeniso lweDHW:		24 kW	30 kW	35 kW
I-Boiler V 'I-CV ye-Net I-CV ye-Gross	kW	24.	30.	35.4
	kW	27	34.	39.3
Ukusetyenziswa kwegesi	m³/h	3.	3.	3.657
	ft³/h	89	111	129
Esona siphumo siphezulu seDHW	kW	24.	30.	35.3
Iqondo lokuHamba kweDHW Kwi-35°C Temp. Phakama	1/min gpm	10.	12.	14.5
		2.	3.	3.2
Ireyithi eKhethekileyo yeDHW	1/min gpm	12.	15.	16.9
		3.	3.	3.7

* Ixabiso lisetyenziswa kwiNkqubo yoVavanyo loMgangatho kaRhulumente wase-UK (SAP) ukulinganisa amandla eendawo zokuhlala. Idatha yovavanyo olubalwe kuyo, iqinisekisiwe ngumzimba owazisiweyo.
C13 C33 C53 = Isixhobo esivaliweyo segumbi esilungiselelwe ukudityaniswa ngeentambo ukuya kwitheminali ethe tyaba okanye ethe nkqo, engenisa umoya omtsha kwisitshisi kwaye ikhuphele ngaphandle iimveliso ezitshayo ngaphandle ngemibhobho ethi, kule meko, igxile. Ifeni iphezulu kumlambo wegumbi lokutsha.
I2H = Isixhobo esenzelwe ukusetyenziswa kwigesi yosapho lwesibini, iGroup Honly.
II2H/3P = Isixhobo esenzelwe ukusetyenziswa kwiigesi zentsapho yesi-2 okanye yesi-3, iQela H okanye i-P.

Icandelo loku-1 – Jikelele

UBUYAYISI WE-BOILER kW	Inombolo yesiXhobo se-GC (iNombolo yoMbhengezo.)
24	47-349-99
30	47-387-01
35	47-387-02

Ilizwe ekusingwa kulo: GB

Kwi-UK, ukuthobela iMimiselo yoKwakha iCandelo L1 (Icandelo 6 eScotland) ibhoyili kufuneka ifakwe ngokuhambelana nemiyalelo yomenzi. Ukuziqinisekisa ukuba ibhoyila ifakelwe ukuthobela iMithetho yeZakhiwo ingabonakaliswa ngokuzalisa kunye nokusayina iBenchmark Commissioning Checklist.
Ngaphambi kokufaka le bhoyila, funda iphepha leKhowudi yokuSebenza ngasemva kule ncwadi.
IINKCUKACHA ZOLUHLU LWENKQUBO YOKUBHEKISA
Ibhoyila ……………………………………………………………………
Yenza kunye nemodeli ………………………………………………… ngasentla
Uthotho lwesixhobo kwibheji yedatha …………….Ikhava yangaphambili
SEDBUK No. % ……………………………………………………….6.
Ulawulo
Ixesha kunye nolawulo lobushushu ukufudumeza ………………………28
Iivalvu zendawo yokufudumeza ………………………………………………….13
Ii-TRV ………………………………………………………………….10
I-Auto bypass …………………………………………………………..13
Unxibelelwano lwebhoyila ………………………………………………………….10
Kuzo zonke iibhoyila
Ukugungxula ukuya ku-BS.7593 ……………………………………………….13
Isithinteli ……………………………………………………………….13
Imowudi yokufudumeza ephakathi
Igalelo lobushushu ………………………………………………. ukubala
Ibhoyila ……………………………………………………………………
Uxinzelelo lokusebenza kwesitshisi …………………………………………n/a
Iqondo lobushushu eliphakathi. ……………….. linganisa kwaye urekhode
Iqondo lokushisa eliphakathi lokubuya. ………….. linganisa kwaye urekhode
Kwiibhoyila ezidibeneyo kuphela
Isinciphisi sesikali ………………………………………………………..13
Imowudi yamanzi ashushu
Igalelo lobushushu ………………………………………………. ukubala
Max. Uxinzelelo lwesitshisi sokusebenza ………………………………n/a
Max. ukusebenza koxinzelelo lwamanzi …………..linganisa & urekhode
Iqondo lokushisa lokungena kwamanzi abandayo …………………………………………………………………....linganisa kwaye urekhode
ITemp yokukhupha amanzi ashushu. .............................................................................................
Umyinge wokuhamba kwamanzi ngobuninzi. useto …………..linganisa kwaye urekhode
Yeebhoyila zokujiya kuphela
Umbhobho wokuhambisa i-condensate ……………………………………………….. 23-24
Kuzo zonke iibhoyila: Gqibezela, sayina kwaye unikezele kumthengi
PHAWULA KUMFAKELI: GCWALISA ULUHLU LWENKUMANKKO YOKWENZIWA KOMTHETHO UZE USHIYE LE MYALELO KUNYE NESIXEKO.

Icandelo loku-1 – Jikelele

1.1. INTSHAYELELO
I-Logic Max Combi 2 C uluhlu lweebhoyili lufakwe eludongeni, ludibanisa, ludibanisa i-gas boilers.
Iimbonakalo:

• Ukusebenza okuphezulu
• Ulandelelwano olupheleleyo
• Umlilo wentlantsi ozenzekelayo
• Umxholo wamanzi aphantsi
• Iflue ephethiweyo

Ibhoyili ibonelelwa ngokupheleleyo kunye ne-DHW plate exchanger heat, valve diverter, impompo ejikelezayo, i-pressure gauge, i-PRV kunye ne-CH isitya sokwandisa.
I-variable CH kunye ne-DHW yokulawula ukushisa kufakwe kulawulo lomsebenzisi kunye nebhoyila ibonakalisa indawo yokutshisa i-DHW.
Ibhoyila ibandakanya njengesiqhelo:
-Ukudlula okuzenzekelayo
– Ukhuseleko kwiqabaka yebhoyila
-Impompo yemihla ngemihla kunye nevalvu yokuphambukisa.
Isingxobo sebhoyila yintsimbi epeyintiweyo emhlophe ethambileyo enephaneli emhlophe yepolima engaphambili.
Ulawulo lobushushu bebhoyila lubekwe ngokubonakalayo kwindawo yolawulo ephambi kwebhoyila.
Isitshintshi sobushushu senziwa nge-aluminiyam etyhidiweyo.
Ibhoyila ifanelekile ukudibanisa kwiinkqubo zokufudumeza ezifakwe ngokupheleleyo, ezivaliweyo KUPHELA. Amalungiselelo afanelekileyo okukhutshwa ngokupheleleyo kwenkqubo ngokubonelelwa kweeqhude zokukhupha amanzi
KUFUNEKA kubonelelwe kumbhobho wofakelo.
Imibhobho esuka kwibhoyila ihanjiswa ezantsi.
I-PRV grommet ifakwe kwibhoyila efuna ukufaniswa okuchanekileyo kunye nokhuseleko lwekliphu (enikezelweyo) ukuqinisekisa ukukhutshwa okukhuselekileyo kwe-PRV ukuba oku kuyenzeka.
Isihluzo seSixokelelwano esiLungileyo sinikezelwa kunye nale bhoyila. Imiyalelo yokufakela oku ibekwe ngaphakathi kwebhokisi yokucoca inkqubo.
Qiniseka ukuba ulandela iSixokelelwano esiLungileyo sofakelo lokucoca kunye nesikhokelo sogcino lwendlela echanekileyo yofakelo. Ukungaphumeleli ukufaka isihluzi senkqubo ngokuchanekileyo kuya kuchaphazela iwaranti yebhoyila.
Icwecwe leDatha
Imodeli yebhoyila kunye nenombolo ye-serial iboniswe kwileyibhile yedatha enokuthi ibekwe phantsi kwebhokisi lebhoyila, eboniswe kwi-Mzobo woQhagamshelwano lwaManzi kunye neGesi.1.2 UKUSEBENZA
Ngaphandle kwemfuno ye-CH, ibhoyila ivutha kuphela xa i-DHW ityisiwe, okanye ngamaxesha athile imizuzwana embalwa ngaphandle kokutsalwa kwe-DHW, ukuze kugcinwe i-DHW ipleyiti yomtshintshisi wobushushu ikwimeko eshushu. Oku kwenzeka kuphela ukuba iqhosha elithi "PREHEAT" licinezelwe kwaye umboniso ufundeka "PREHEAT ON or PREHEAT TIMED".
Xa kukho imfuno ye-CH, inkqubo yokufudumala inikezelwa kwiqondo lokushisa elikhethiweyo phakathi kwe-30 o C kunye ne-o 80 C, de kube i-DHW ikhutshwe. Imveliso epheleleyo esuka kwibhoyila iye yalathwa ngevalve yokuphambukisa kwipleyiti yomtshintshi wobushushu ukuze kubonelelwe ngokutsalwa kwe-DHW yesiqhelo:
24 kW 9.9 l/min kwi-35ºC ukunyuka kobushushu.
30 kW 12.4 l/min kwi-35ºC ukunyuka kobushushu.
35 kW 14.5 l/min kwi-35ºC ukunyuka kobushushu.
I-DHW yokutsalwa kwesantya echazwe ngasentla ligama eliza kunikezelwa ngumlawuli webhoyila. Ngenxa yokwahluka kwenkqubo kunye nokuguquguquka kwamaxesha onyaka amanqanaba okuhamba kweDHW/ukunyuka kobushushu kuya kwahluka, kufuna uhlengahlengiso kwitephu yokutsalwa.
Kumazinga asezantsi okutsalwa kwe-DHW ubushushu obuphezulu bunokugqitha kuma-65ºC.
Ibhoyila inenkqubo yokuxilonga ebanzi enika ulwazi oluneenkcukacha malunga nobume bebhoyila xa isebenza, kunye nokusebenza kwamacandelo aphambili ukunceda ukugunyaziswa kunye nokufumanisa iimpazamo.
1.3 UKUPHATHWA NGOKUKHUSELEKILEYO
Le bhoyili inokufuna abasebenzi aba-2 okanye ngaphezulu ukuyihambisa kwindawo yayo yokufakela, ukuyisusa kwisiseko sayo sokupakisha kwaye ngexesha lokuhamba kwindawo yofakelo. Ukulawula ibhoyila kunokubandakanya ukusetyenziswa kwelori yengxowa kwaye kubandakanya ukuphakamisa, ukutyhala kunye nokutsala.
Isilumkiso kufuneka sisetyenziswe ngexesha lale misebenzi. AbaSebenzi kufuneka babe nolwazi ekuphatheni ubuchule xa besenza le misebenzi kunye nezi lumkiso zilandelayo
kufuneka kuthathelwe ingqalelo:

• Bamba ibhoyila kwisiseko.
• Yiba namandla ngokwasemzimbeni.
• Sebenzisa izixhobo zokuzikhusela ngokufanelekileyo, umz. iiglavu, izihlangu zokhuseleko.

Ngethuba lazo zonke iintshukumo kunye nezenzo zokuphatha, zonke iinzame kufuneka zenziwe ukuze kuqinisekiswe oku kulandelayo ngaphandle kokuba kungenakuphepheka kunye / okanye ubunzima bulula.

• Gcina umva ngqo.
• Kuphephe ukujija esinqeni.
• Kuphephe ukugoba okuphezulu komzimba / ngaphezulu kunzima.
• Hlala ubambe entendeni yesandla.
• Sebenzisa ukubamba ngesandla okuchongiweyo.
• Gcina umthwalo ngokusondeleyo kumzimba ngokusemandleni.
• Ngalo lonke ixesha sebenzisa uncedo ukuba luyafuneka.

1.4 IZINTO ONGAZIKHETHA
Nceda undwendwele i-idealheating.com ukufikelela kwizinto ozikhethelayo zale bhoyila.

https://idealheating.com/logic-V4-literature-1

1.5 UKHUSELEKO
Ukhuseleko lwerhasi yangoku (ufakelo kunye nokusetyenziswa) imigaqo okanye imithetho esebenzayo:
Isixhobo sifanelekile kuphela ukufakwa e-UK kwaye kufuneka sifakwe ngokuhambelana nemigaqo esebenzayo. E-UK, ufakelo kufuneka lwenziwe yiNjineli eBhalisiweyo yeGesi eKhuselekileyo. Kufuneka yenziwe ngokuhambelana neemfuno ezifanelekileyo ze:

• Ukhuseleko lwerhasi (uFakelo kunye nokusetyenziswa) Imigaqo
• Imithetho yeZakhiwo efanelekileyo, nokuba siSakhiwo
  Imimiselo, iMithetho yeZakhiwo (eSkotlani), iMithetho yeZakhiwo (iNorthern Ireland).
• Imimiselo yokuFakelwa kwamanzi okanye iMithetho yaManzi eSkotlani.
• Imithetho ye-IEE yocingo yangoku.
  Apho kungekho miyalelo icacileyo inikwayo, kufuneka kubhengezwe kwiKhowudi yoMgangatho yaseBritane efanelekileyo.

I-Boiler iye yavavanywa kwaye yaqinisekiswa: BSEN 15502-1, BSEN 15502-2, BSEN 15502-2-1, BSEN 60335-1, BSEN 60335-2-102, BSEN 55014-1 kunye
I-BSEN 55014-2 yokusetyenziswa kunye neGesi yeNdalo kunye nePropane.
Iingcebiso ezineenkcukacha ziqulethwe kule MiGangatho yaseBritane ilandelayo IiKhowudi zokuSebenza:

BS5440:1	Imikhuhlane (kwizixhobo zegesi zegalelo elilinganisiweyo elingadlulanga kuma-70 kW).
BS5440:2	Ukungenisa umoya (kwizixhobo zegesi zegalelo elilinganisiweyo elingadlulanga kuma-70 kW).
BSEN12828	Iinkqubo zokufudumeza kwizakhiwo: Uyilo lweenkqubo zokufudumeza ezisekwe emanzini.
BSEN12831	IiNkqubo zokufudumeza kwizakhiwo: Indlela yokubala yoyilo lomthwalo wobushushu.
BSEN14336	Iinkqubo zokufudumeza kwizakhiwo: Ufakelo kunye nogunyaziso lweenkqubo zokufudumeza ezisekelwe emanzini.
BS5546	Ufakelo lonikezelo lwamanzi ashushu ngerhasi ukulungiselela iinjongo zasekhaya (2nd Family Gases)
BS6798	Ukufakwa kweebhoyila zamanzi ashushu ezibaswe ngerhasi zegalelo elilinganisiweyo elingadlulanga kuma-70 kW.
BS6891	Ukufakwa kunye nokugcinwa kombhobho wofakelo lwegesi yoxinzelelo oluphantsi.
BS 7593:2019	Indlela yokusebenza yokulungiselela, ukugunyazisa kunye nokugcinwa kweenkqubo zokufudumeza ezisembindini zasekhaya kunye nokupholisa amanzi.

Uxwebhu lweMpilo noKhuseleko No.635.
UMbane eMsebenzini weMimiselo, ka-1989.
Amanqaku omenzi AKUMELE athatyathwe, nangayiphi na indlela, njengengaphezulu kwezibophelelo ezisemthethweni.
EBALULEKILEYO T: Esi sixhobo sinesatifikethi se-UKCA/CE sokhuseleko nokusebenza. Musa ukuqhagamshela izixhobo zolawulo lwangaphandle ngokuthe ngqo kwesi sixhobo ngaphandle kokuba ucetyiswe kule ncwadana okanye ngokuFundisa okuFanelekileyo ngokubhaliweyo. Ukuba uyathandabuza, nceda ubuze. Izixhobo zolawulo ezingavunywanga zinokwenza iwaranti yesi sixhobo ingasebenzi kwaye zophule iMimiselo yoKhuseleko lweGesi.
1.6 UKUPHATHWA NGOKUKHUSELEKILEYO KWEMICIMBI
Akukho asbestos, imekyuri okanye CFCs zibandakanyiwe kuyo nayiphi na indawo yebhoyila okanye ukwenziwa kwayo.
1.7 INDAWO YEBOILER
Ibhoyila kufuneka ifakwe kudonga lwangaphakathi oluthe tyaba oluthe nkqo, olukwazi ukuxhasa ngokwaneleyo ubunzima bebhoyila kunye naso nasiphi na isixhobo esincedisayo.
Ibhoyila inokuthi ifakwe eludongeni oluvuthayo kunye ne-insulation phakathi kodonga kunye nebhoyili ayimfuneko, ngaphandle kokuba ifunwa ngugunyaziwe wendawo.
ISILUMKISO: Ukufikelela ngasemva kwibhoyila akuvumelekanga.
ISILUMKO: Musa ukungena kwibhoyila ngaphandle.
Izakhiwo ezenziwe ngamaplanga
Iibhoyili ezifakwe kwisakhiwo esifakwe ngamaplanga kufuneka zihambelane ne-IGE / UP7 + A 2008.
Ukufakwa kwegumbi lokuhlambela
ISILUMKO: Esi sixhobo silinganiselwe nge-IP20, musa ukucoca ngeejethi zamanzi.
Ungafakela ibhoyila nakwesiphi na isithuba sangaphakathi. Ufakelo kufuneka luhambelane ne-IEE (BS 7671) yangoku yeMimiselo yocingo kunye nemigaqo yombane esebenzayo eSkotlani.
Ukuba eso sixhobo siza kufakwa kwigumbi elinebhafu okanye ishawari ngoko ke eso sixhobo kufuneka sifakwe ngaphaya koMmandla 2, njengoko kucacisiwe kwi-BS7671.Ukufakwa kwegumbi lokuhlambela
[0] Indawo ye0
[1] Indawo ye1
[2] Indawo ye2
[2 *] Ngaphandle kodonga lokugqibela, ummandla we-2 kufuneka wandise i-600 mm ukusuka kwindawo yokuhlambela
[A] 600 mm irediyasi ukusuka ebhafini okanye kwishawari
UFakelo lweCompartment
Ibhoyili efakwe kwi-compartment ayifuni ukungena komoya.
Nangona kunjalo, Ibhoyila efakwe kwikhompatimenti kufuneka ibonelele ngococilelo olwaneleyo lokusevisa. Ikhompatimenti kufuneka kwakhona ifakwe ileyibhile efanelekileyo ngokuhambelana nemigangatho yangoku.

1.8 UKUNIKEZELWA KOMOYA
Akuyimfuneko ukuba kubekho i-air vent kwigumbi okanye kwindawo yangaphakathi apho ibhoyili ifakwe khona.
1.9 UKUNIKEZELWA NGEGAS
Qhagamshelana nomthengisi werhasi wasekhaya ukuze aseke ubonelelo olwaneleyo lwerhasi. Musa ukusebenzisa imibhobho yenkonzo ekhoyo ngaphandle kokubonisana nomthengisi wegesi wendawo.
Unikezelo lwerhasi kufuneka lulawulwe ngemitha.
Imitha yegesi inokudityaniswa kuphela ngumthengisi werhasi wasekhaya okanye yiNjineli eBhalisiweyo yeGesi eKhuselekileyo.
Imitha ekhoyo kufuneka ihlolwe, ngokukhethekileyo ngumthengisi wegesi, ukuqinisekisa ukuba imitha yanele ukujongana nomlinganiselo ofunekayo wokubonelela ngegesi.
Luxanduva loMfaki weGesi ubungakanani bombhobho wofakelo lwegesi ngokuhambelana ne-BS6891.
Ngelixa umgaqo we-1: 1 ivelufa yegesi iqinisekisa ukuba uluhlu lwe-Logic luyakwazi ukuzisa imveliso epheleleyo kuxinzelelo lwe-inlet olusezantsi njenge-14 mb, ezinye izixhobo zegesi kwipropati zisenokunganyamezeli kangako. Xa uxinzelelo lokusebenza lufunyaniswa lungaphantsi kobuncinane bemitha yokuphuma kwe-19 mb ezi kufuneka zihlolwe ukuqinisekisa ukuba oku kwanele ukusebenza okuchanekileyo nokukhuselekileyo. Ukuvumela ilahleko yoxinzelelo olwamkelekileyo lwe-1mb kumbhobho wofakelo, kunokucingelwa ukuba ubuncinci obuvunyelweyo boxinzelelo lokusebenza lwe-18mb luya kusiwa kwindawo yokungena kwisixhobo.
(Isalathisi BS6400-1 Igatya 6.2 Ukufunxa ngoxinzelelo).
Iqhude legesi langaphandle linganciphisa ngakumbi uxinzelelo lokusebenza xa lilinganiswe kwindawo yokuvavanya. Ukuhla koxinzelelo kuhambelana negalelo lobushushu kwibhoyila (kW), bhekisa kwigrafu engezantsi.

OKUBALULEKILEYO: Qinisekisa ukuba lonke uqhagamshelo lwevalvu yegesi luqinile kwaye kujongwe ukuvakala kwegesi ukuya kwivalvu yokulawula igesi.
Imibhobho yofakelo kufuneka ifakwe ngokuhambelana ne-BS6891.
Ufakelo olupheleleyo KUFUNEKA luvavanyelwe ukuxinana kwegesi kwaye lucocwe njengoko kuchaziwe, kuninzi lofakelo umgangatho ofanelekileyo yi-IGEM/UP/1B [23], kodwa kungenjalo IGEM/UP/1 [21] okanye IGEM/UP/1A [22] ], njengoko kufanelekile, inokusetyenziswa.
1.10 INKQUBO YOKUJONGA AMANZI
OKUBALULEKILEYO: Ubuncinane bobude obuyimitha e-1 yombhobho wobhedu MAFAKA ifakelwe kuzo zombini iindlela zokuhamba nokubuyisela uqhagamshelo olusuka kwibhoyila phambi kokuba kudityaniselwe nawuphi na umbhobho weplastiki.
Inkqubo yokufudumala ephakathi kufuneka ihambelane ne-BS6798 kwaye, ngaphezu koko, kwiinkqubo ezincinci kunye ne-microbore, i-BS5449.
Ukucocwa kwamanzi kugutyungelwe kamva kule miyalelo.

1.11 IMILAWULO YEBHAYIILE
Faka ulawulo lwe-CH ukuqinisekisa ukuba ibhoyili ayinayo imfuno xa kungekho mfuneko kwinkqubo.
Iinkqubo zokufudumeza ezine-TRV kumagumbi ngamnye kufuneka zibandakanye i-thermostat ukulawula ubushushu kumagumbi angenayo i-TRVs. Ubuncinci i-10% yemveliso encinci yokushisa kwibhoyili kufuneka iphunyezwe ngokusebenzisa i-thermostat yegumbi. Isekethe ye-bypass ene-automatic bypass valve kufuneka ifakwe kwiisistim ezine-TRVs okanye i-valve-port valves kuzo zonke ii-radiator ukuqinisekisa ukuhamba kwamanzi.
1.12 INKONZO YOMbane
ISILUMKISO: Esi sixhobo kufuneka sifakwe emhlabeni
Iintambo zangaphandle kwisixhobo kufuneka zihambelane ne-IEE (BS7671) yangoku yeMigaqo yeeNcingo kunye nayo nayiphi na imigaqo yasekuhlaleni esebenzayo.
Ubonelelo lombane kwibhoyila kunye neziko locingo lwenkqubo luya kusetyenziswa ngokudibeneyo kwipali enye edityanisiweyo ephindwe kabini kunye neenkqubo zokufudumeza ezintsha, kwaye apho kufakelo olubambekayo olufakelwayo, isihlukanisi siya kuba kufuphi nesixhobo sombane.
1.13 I-CONNDENSATION RAIN
Idreyini ye-condensate ebonelelweyo kufuneka idityaniswe kwindawo yokuhambisa amanzi kwisiza. Yonke imibhobho yamanzi econdensate kunye nezifakelo kufuneka zenziwe ngeplastiki.
OKUBALULEKILEYO: Umbhobho we-condensate drain kufuneka ufakwe ngokuhambelana ne-BS6798.
I-drain outlet kwibhoyili ilingana nomgangatho we-21.5 mm umbhobho ophuphumayo. Kukulungeleka jikelele ukuvumela ukusetyenziswa kweempawu ezahlukeneyo zemibhobho.1.14 IMILINGANISELO YE-BOILER, IINKONZO & NONCEDO
Ukudibanisa kwibhoyila kwenziwa kwimisila yokudibanisa kwibhoyila.
Obu buncinane bokucolwa bulandelayo kufuneka bugcinwe ukuze kusebenze kwaye kunikezelwe iinkonzo.
Kuya kufuneka indawo eyongezelelweyo yofakelo, ngokuxhomekeke kwiimeko zesiza.
Icala kunye neFlue yangasemva
a. Ngaphandle kokuba umngxuma we-flue usikwe ngokuchanekileyo, umz. nge-core drill, i-flue inokufakwa ngaphakathi kwesakhiwo apho ubukhulu bodonga bungagqithi kwi-600 mm.

Ukucoca ngaphambili
Ubuncinane bokucoceka okungaphambili xa kusakhelwe ekhabhathini yi-5 mm ukusuka kucango lwekhabhathi kodwa i-450 mm yokucocwa iyonke kusafuneka, nocango lwekhabhathi luvuliwe, ukuze kusetyenziswe.
* Ukucoca okusezantsi
Ukukhutshwa okuphantsi emva kokufakwa kungancitshiswa ukuya kwi-15 mm.
Oku kufuneka kufunyanwe ngephaneli eshenxiseka lula ukunika i-100 mm imvume efunekayo ekusekweni.
Ukufikelela lula kwigeyiji yoxinzelelo kufuneka imvume esezantsi ye-15 mm kumnyango ovulekileyo.
I-PRV Grommet EBALULEKILEYOT: Nceda uqinisekise ukuba kukho ucoceko olwaneleyo nakweliphi na icala nangaphantsi kwebhoyila, ngakumbi ukusuka kwiihenjisi zocango kunye nesiseko sekhabhathi, ukuvumela ucango ukuba luvulwe ukuvumela ukuba igeyiji yoxinzelelo ijongwe. Kwakhona qinisekisa ukuba kukho ukufikelela okwaneleyo kwisihluzo senkqubo yokukhupha amanzi, ukucoca kunye nedosi. Ukufumana isikhokelo nceda ujonge iNcwadana yoFakelo lweSixokelelwano esiLungileyo.
1.15 IIMFUNO ZENKQUBO – UKUSHISA OKUPHAKATHI
a. Indlela yokuzaliswa, ukugcwalisa, ukugquma okanye ukugungxulwa kweesekethe zamanzi ashushu ezitywiniweyo ezingundoqo ukusuka kumbhobho oyintloko ngokusebenzisa uqhagamshelo lombhobho wexeshana uvumeleke kuphela ukuba kwamkelekile kugunyaziwe wamanzi wendawo.
b. Ulwelo lwe-Antifreeze, i-corrosion kunye ne-scale inhibitor fluids ezifanelekileyo ukusetyenziswa kunye neebhoyila ezine-aluminiyam zokutshintshiselana kobushushu zingasetyenziswa kwinkqubo yokufudumeza ephakathi.
Icandelo loku-1 – Jikelele
1.15 IIMFUNO ZENKQUBO – UKUSHISA OKUPHAKATHI
a. Indlela yokuzaliswa, ukugcwalisa, ukugquma okanye ukugungxulwa kweesekethe zamanzi ashushu ezitywiniweyo ezingundoqo ukusuka kumbhobho oyintloko ngokusebenzisa uqhagamshelo lombhobho wexeshana uvumeleke kuphela ukuba kwamkelekile kugunyaziwe wamanzi wendawo.
b. Ulwelo lwe-Antifreeze, i-corrosion kunye ne-scale inhibitor fluids ezifanelekileyo ukusetyenziswa kunye neebhoyila ezine-aluminiyam zokutshintshiselana kobushushu zingasetyenziswa kwinkqubo yokufudumeza ephakathi.
Ngokubanzi

1. Ufakelo kufuneka luhambelane nemimiselo kazwelonke neyendawo.
2. Yila inkqubo yobushushu bokuhamba ukuya kuthi ga kwi-80 C.
3. Amacandelo enkqubo kufuneka afanelekele uxinzelelo olusebenzayo lwe-3 bar kunye nobushushu obukhulu be-110 ° C.
   La malungu alandelayo afakwe kwisixhobo:
   a. Impompo ejikelezayo.
   b. I-PRV, ene-non-adjustable preset lift pressure of 3 bar.
   c. Igeyiji yoxinzelelo, egubungela uluhlu lwe-0 ukuya kwi-4 bar.
   d. Isitya sokwandisa iilitha ezi-8, kunye noxinzelelo lokuqala lwentlawulo ye-0.75 bar.

4. Makeup Water.
Elinye lala malungiselelo alandelayo kufuneka lenziwe lokutshintsha inkqubo yokulahleka kwamanzi:
a. Isitya esizaliswe ngesandla
Inqanawa kufuneka:

• Yiba nenqanaba lamanzi elibonakalayo
• Yixhonywe ubuncinane nge-150 mm ngaphezu kweyona ndawo iphezulu yesixokelelwano
• Xhuma ngevalve engabuyi kwisistim
• Yiba ubuncinane i-150 mm ngaphantsi kwesitya sokwenza izinto kwicala lokubuya kweeradiyetha

b. Uxinzelelo lwenkqubo.
Ukusebenza kakuhle kwenqanawa yokwandisa kuya kuncitshiswa kwinkqubo yoxinzelelo; isitya esikhulu okanye umthamo wenkqubo encinci unokufuneka. Ukuba umthamo wenqanawa awunakwanela, isitya esongezelelweyo kufuneka sifakwe ekubuyiseleni kwibhoyili.
Ukuba inkqubo ayicinezeleki, umthamo wamanzi abandayo akufanele udlule i-143 ilitha.
Isikhokelo malunga nokulinganisa inqanawa sinikwe kwiThebhile 4.
Isantya sokuhamba kwamanzi kunye nelahleko yoxinzelelo

Isiphumo se-CH esiphezulu	kW	24.2
Ireyithi yokuHamba kwamanzi	l/min (gal/min)	17.3 (3.8)
Umahluko kumaqondo obushushu	o C	20
Intloko ekhoyo kwiNkqubo	umg (ft.wg)	3.4 (11.1)
NgeSixokelelwano esiLungileyo Isihluzi esiFakelweyo kunye neeValufa	umg (ft.wg)	3.1 10.2

Uluhlu lwesi-4 Ubungakanani besitya

I-PRV bar yokumisela	3.0
Ibha yoxinzelelo lwesitya	0.5 ukuya 0.75
Ibar yoxinzelelo lwenkqubo yokuhlawulisa kwangaphambili	Akukho nanye	1.0
Umthamo wenkqubo	Inqanawa yokwandisa
(iilitha)	umthamo (iilitha)
25	2.	2.
50	3.	4.
75	5.	6.
100	6.	7.
125	8.	9.
150	9.	11.0
175	11.	13.
190	12.	14.0
200	13.	15.
250	16.	18.
300	19.	22.
Kwezinye iivolyum zesistim phinda-phinda ngefactor ngapha	0.063	0.074

5. Ukuzalisa
Inkqubo inokuzaliswa ngale ndlela ilandelayo:
Apho uxinzelelo oluphambili lugqithise kakhulu ivalve yokunciphisa uxinzelelo kufuneka isetyenziswe ukuququzelela ukuzaliswa.
a. Gcoba ngokucokisekileyo yonke inkqubo ngamanzi abandayo.
b. Gcwalisa kwaye ukhuphe inkqubo kuze kube yilapho i-gauge yoxinzelelo ibhalisa ibha ye-1 kwaye uhlolisise ukuvuza.

c. Khangela ukuba umbhobho we-15 mm wedayamitha ubekwe ngokuchanekileyo kwaye ukhuselwe (usebenzisa ikliphu enikezelweyo)
d. Jonga ukusebenza kwe-PRV ngokuphakamisa uxinzelelo lwamanzi de i-valve iphakame. Oku kufuneka kwenzeke ngaphakathi kwe-0.3 bar yoxinzelelo lokunyuswa kwangaphambili.
e. Khangela ukuba akukho kubaleka kwamanzi okwenzekayo ngaphandle kwendawo yokukhupha
f. Ukukhulula amanzi kwinkqubo kude kube yinkqubo encinci yoxinzelelo loyilo;
1.0 bar ukuba isistim iza kucinezelwa kwangaphambili.
1.16 IIMFUNO ZENKQUBO – DHW
Amanzi Ashushu Asekhaya

1. Inkonzo yeDHW kufuneka ihambelane ne-BS.5546 & BS6700.
2. Jonga kwiThebhile 1 ngoxinzelelo oluphantsi kunye nolona luphezulu lokusebenza. Kwiindawo eziphantsi koxinzelelo lwamanzi angundoqo umlawuli wamanzi ashushu asekhaya unokususwa
   Ikhatriji ye-injini ye-DHW yokuhamba. Ibhoyila iya kufuna umlinganiselo wokuqukuqela ukusetwa ukufumana ukunyuka kwamaqondo obushushu angama-35 C kwimpompo ekude kakhulu kwibhoyila.
3. Iibhoyili zifanelekile ukudibanisa kwiintlobo ezininzi zomatshini wokuhlamba kunye nezixhobo zokuhlamba izitya.
4. Ukuba ishawari/ivalve yomxube ayibandakanyi iivalvu ezingabuyiyo oku kulandelayo makulandelwe:
   a. I-inlet ebandayo kwibhoyili ifakwe i-anti-vacuum evunyiweyo okanye i-siphon engabuyi i-valve.
   b. Amanzi ashushu nabandayo kwishawari anoxinzelelo olulinganayo.
5. Iindawo zamanzi anzima
   Apho ubulukhuni bamanzi bungaphezulu kwe-200 mg/litha (200 ppm), kucetyiswa ukuba isixhobo sokunciphisa isikali sobumnini sifakelwe kwibhoyila ebandayo yonikezelo ngokweemfuno zenkampani yamanzi yasekuhlaleni.

OKUBALULEKILEYO: Makwenziwe isibonelelo ukulungiselela ukwandiswa kweDHW equlethwe kwisixhobo sombane. Ukuba i-DHW inlet iqulethe ukuthintela ukuhamba ngasemva
isixhobo okanye ivelufa engabuyiyo, umz. imitha yamanzi, emva koko isitya esincinci sokwandisa kufuneka sifakwe phakathi kwesixhobo kunye nebhoyila kumbhobho obandayo wokungena.
Amanzi abandayo, undoqo wokunyuka kunye nemibhobho kwiindawo ezivulelekileyo kufuneka ashiywe ngokufanelekileyo ukuthintela umkhenkce.
Qaphela Ikhithi yoKwandiswa kweVessel ye-DHW ifumaneka kwi-Ideal.
1.17 UKULINGANA KWENKQUBO
Ibhoyila ayidli ngokufuna i-bypass kodwa ubuncinci ezinye iiradiyetha kwisekethe yokufudumeza, yomthwalo ongaphantsi kwe-10% yemveliso yebhoyila encinci, kufuneka ibonelelwe ngeevalvu ezimbini zokutshixa ukuze obu buncinci bomthwalo wokufudumeza buhlale bufumaneka.
Phawula. Iinkqubo ezibandakanya iivalvu zezowuni ezinokuvala ngokupheleleyo ukuhamba kwesixokelelwano kufuneka nazo zibandakanye i-bypass.
Ukulinganisa

1. Cwangcisa umdwelisi wenkqubo ukuba IVULIWE.
2. Vala iivalve ze-manual okanye ze-thermostatic kuzo zonke iiradiyetha, ushiya iivalve ezimbini zokutshixa (kwiiradiyetha ekubhekiselwe kuzo ngasentla) zikwimo eVULAYO.
3.  Nyusa i-thermostat yegumbi kwaye ulungise ivalve yesitshixo ukunika ukuhamba okungaphazamisekiyo kwiradiyetha. Ezi zivalo kufuneka ngoku zishiywe zisetiwe.
4. Vula zonke iivalvu zeradiyetha ezenziwe ngesandla okanye ze-thermostatic kwaye ulungelelanise izivalo ze-lockshield kwiiradiyetha eziseleyo, ukunika malunga ne-20 oC ubushushu behla kwiradiyetha nganye.
5. Lungisa i-thermostat yegumbi kunye nomdwelisi weprogram
   Iisetingi EZIQHELEKILEYO.
   Phawula. Iinkqubo ezibandakanya iivalvu zezowuni ezinokuvala ngokupheleleyo ukuhamba kwesixokelelwano kufuneka nazo zibandakanye i-bypass.

1.18 UKUNYANGWA KWAMANZI
ISILUMKO: Musa ukugcwalisa inkqubo yokufudumeza ngamanzi athambileyo. Amanzi athambekisiweyo anokwenza umhlwa.
Ubushushu basesiphakathini
Uluhlu lwe-Logic yeebhoyili zine-ALUMINIUM i-alloy exchanger heat.
KUBALULEKILEYO Ukusetyenziswa kwalo naluphi na olunye unyango kule mveliso kunokunika isiqinisekiso soKufudumeza okuFanelekileyo singasebenzi.
I-Ideal System Filter iya kunceda ngokuchasene nokwakhiwa kwe-debris ye-iron oxide, nangona kunjalo unyango olungaphantsi kwamanzi luyacetyiswa nguKufudumeza okuPhambili.
Ukufudumeza okufanelekileyo kuncoma ukuNyangwa kwamanzi ngokuhambelana neNqaku zeSikhokelo seBenchmark kuNyango lwaManzi kwiiNkqubo zokufudumeza eziseMbindini.
Ukuba unyango lwamanzi lusetyenzisiwe, i-Ideal Heating incoma kuphela ukusetyenziswa kwe-SCALEMASTER SM-1 PRO, i-FERNOX MBI, i-ADEY MC1, i-SENTINEL X100 okanye i-CALMAG CM100 inhibitors kunye nemveliso yonyango yamanzi ehambelana nayo, ekufuneka isetyenziswe ngokuhambelana nemiyalelo yabavelisi.

1. Kubaluleke kakhulu ukuba ugxininiso oluchanekileyo lweemveliso zonyango lwamanzi lugcinwe ngokuhambelana nemiyalelo yabavelisi.
2. Ukuba ibhoyila ifakwe kwinkqubo esele ikho naziphi na izongezo ezingafanelekanga KUFUNEKA zisuswe ngokucocwa ngokucokisekileyo. I-BS7593: 2019 inika iinkcukacha ngamanyathelo ayimfuneko okucoca inkqubo yokufudumala yasekhaya.
3. Kwiindawo ezinamanzi aqinileyo, unyango lokuthintela isikali sekalika lunokuba yimfuneko – nangona kunjalo ukusetyenziswa kwamanzi athanjisiweyo AKUVUMELEKANGA.
4. Naphantsi kwazo naziphi na iimeko kufuneka ibhoyila igxothwe phambi kokuba inkqubo igungxulwe ngokupheleleyo.
   Ngolwazi oluthe vetshe qhagamshelana:
   Fernox www.fernox.com Umnxeba: +44 (0) 3301 007750
   Izisombululo zokuSebenza kweSentinel www.sentinelprotects.com Umnxeba: +44 (0) 1928 704330
   Isikali seAster Water Treatment Products www.scalemaster.co.uk Umnxeba: +44 (0) 1785 811636
   Calmat Ltd. www.calmagLtd.com Umnxeba: +44 (0) 1535 210320
   Adey www.adey.com Umnxeba: +44 (0) 1242 546700

Icandelo 2 -Ufakelo

2.1 INDIBANO YESIBHAYIBHILE – IYAPHUPHUMA VIEW

I-104 CH iValve yokuBuyisa	119 Buyisela Ubuninzi beQela	218 Gasket – Burner	324 Ibhokisi Yokulawula Isivalo
I-105 CH iValve yokuHamba	120 Ukuqukuqela kweQela lokuHamba	219 Sump Coca Ikhava	325 Ibhokisi Yokulawula Ngaphambili
I-106 ye-DHW yokuNgena kunye nokuPhuma	121 Isitya sokuTshintsha ubushushu	223 Umkhuhlane omninzi	326 Ufakelo olungenanto
107 Ukuzalisa uMbhobho weLoop	124 Umlawuli wokuHamba	224 Flue Manifold Top	401 Injini yobushushu
108 Intloko yeMpompo	I-127 i-Flow Sensor/iTurbine	227 Iklamp Ukugcina iFlue Turret	503 Isibiyeli sokuFaka eludongeni
110 iAuto Air Vent	131 Ukutshintsha koxinzelelo lwamanzi	228 Hose Condensate Ngaphakathi	504 Iphaneli engaphambili
111 Diverter Valve Motor	135 Uvavanyo loxinzelelo	229 Umgibe weCondensate	505 IFascia
I-112 Diverter iValve uMzimba kunye nePaddle	203 Gas Cock	231 uQhagamshelo lweNgxoxo yeCondensate	506 Isibiyeli – iSpark Generator
113 Ivalve yoNcedo loxinzelelo	205 iValve yegesi	239 Umbhobho we-Condensate Drain	507 Isibiyeli – Isitya soKwandiswa
114 Umbhobho – PRV Outlet	206 Umbhobho – Isitofu segesi	302 PCB
115 Umbhobho – Phula	211 Injector Assy	306 I-Electrode yokuBonelela
116 Umbhobho – Buyela	214 Venturi	308 iYunithi yoMbane
117 Umbhobho – Isitya Sokwandiswa	215 Umlandeli	309 IThermistor
118 Isitya Sokwandiswa	217 sokukhuphela	313 I-Ignition lead

Phawula ukuba amanani ento aqhagamshelwe kuluhlu olusecaleni

2.2 UKUQALA

Ibhoyila ibonelelwe idityaniswe ngokupheleleyo kwiPack A.
Pakisha imixholo

1. Ibhoyila
2. Ibhokisi yokupakisha yeHardware
3. Ipleyiti yokuNyusa udonga
4. Le Miyalelo yoFakelo / Abasebenzisi
5. Iwaranti yeBoiler
6. Ithempleyithi yokuNyusa ngodonga
7. Umbhobho wePRV
8. Isihluzi seNkqubo eNgconoIsixhobo seHardware
   Imixholo Yebhokisi
9. I-1x i-HP Box Dividers - 289 x 111 x 57.5 mm
10. I-1x Iplagi yeNdoda kunye neClip
11. 1x Umbhobho we-DHW Outlet
12. 1x Umbhobho wokuzalisa iLoop
13. I-1x ye-Valve ye-DHW yokungena
14. 2x Umbhobho CH Ukuhamba / ukuBuyisa
15. I-1x ye-Valve yokuZalisa iLoop
16. I-1x I-Valve CH G 3/4 x 22 mm yokuZalisa iLoop
17. 1x Cap Female
18. I-1x iValve CH G 3/4 x 22 mm
19. 1x Umbhobho wokungenwa kweDHW
20. 1x Nut G 1/2 x 16 Brass (Flat)
21. 1x Gas Cock
22. 1x Ikliphu yePRV
23. Imixholo yeBag yesincedisi
24. 9x iiwasha*
25. Iiplagi ze-2x eludongeni
26. 2x Izikrufu
27. 1x Flue Clamp Screw

2.3 ITHEMPLEYITHI YOKUFAKA UDONGO
OKUBALULEKILEYO: Qinisekisa ukuba udonga apho ibhoyila iya kuba sicaba.
Ithempleyithi yokufaka udonga ibekwe kwipakethe yangaphakathi yokukhusela. Ithemplethi ibonisa indawo yokulungisa kunye nemingxuma yeziko le-flue yangasemva yofakelo oluqhelekileyo.

1. Khusela itemplate kwindawo efunekayo. Qinisekisa ukuba sisikwere ngokuxhoma imibhobho yamanzi.
2. Ukuba ufaka iflue esecaleni, yandisa umgca osembindini weflue ecaleni nge-155 mm kumgangatho wokulungisa udonga okanye ngama-200 mm ukuba usebenzisa isibiyeli sokumisa.
3. Phawula oku kulandelayo eludongeni:
   a Iqela elikhethiweyo lemingxunya yezikrufu eludongeni.
   b. Indawo esembindini yombhobho weflue. Ukumakisha zombini iziko kunye nomjikelezo we-flue duct.
4. Susa ipleyiti yetemplate eludongeni.

2.4 UKULUNGISA UDONGA
ISILUMKISO: Qinisekisa ukuba, ngexesha lomsebenzi wokusika, i-masonry ewela ngaphandle kwesakhiwo ayibangeli umonakalo okanye ukulimala komntu.

1. Jonga zonke iindawo zemingxuma phambi kokomba.
2. Sika umngxuma we-flue nge-127 mm core boring tool, qinisekisa ukuba umngxuma unesikwere eludongeni.
3. Gqoka imingxunya emi-2 yokuxhoma nge-7.5 mm / 8 mm ye-masonry drill uze ufake iiplagi zeplastiki ezibonelelweyo.
4. Khangela izikrufu ezi-2 ze-14 No.50 x 3 mm kwipleyiti yokuxhoma eludongeni (enye kwicala ngalinye, kuyo nayiphi na imingxunya emi-XNUMX enikezelweyo kwicala ngalinye) kunye nesijiva sasekhaya. Qinisekisa isibiyeli sokunyusela
inqanaba.

2.5 UKUFAKA Ipleyiti YOKUFAKA UDONGA

1. Krwela ipleyiti yodonga eludongeni usebenzisa iiplagi ezi-2 ezifakelwe ngaphambili ngezikrufu ezi-2 ezinikiweyo.
2. Khetha enye kwiiseti ezi-2 kwiindawo zokubeka kwibhanki ekhohlo nasekunene. Qinisekisa ukuba ubuncinane esinye sezikhonkwane sifakelwe kwisithuba esiphezulu kwaye isibiyeli sokuxhoma sikwinqanaba.

2.6 UKUFAKA I-BOILER

1. Phakamisa ibhoyila kwipleyiti yokufakwa eludongeni kwaye uyibeke phezu kwe-tabs ezi-2.

2.7 IFULA KUNYE NENDAWO
Le ncwadana yofakelo kunye nenkonzo kufuneka ifundwe kunye nekhithi yeflue kunye nesikhokelo esifanelekileyo. 

I-Telescopic flue oxwesileyo yi-0.5 okanye 0.7 m Inxalenye efanelekileyo. 0.5 m 208169 0.7 m 208174	Umsinga othe tyaba 0.6 okanye 0.8 m Inxalenye efanelekileyo. 0.6 m 208171 0.8 m 217442	Ukwandiswa komkhuhlane 0.5 m, 1 m okanye 2 m Inxalenye efanelekileyo. 0.5 m 211037 1 m 203129 2 m 211038	Isithinteli somkhuhlane Inxalenye efanelekileyo. 208176	Itheminali yomlambo othe nkqo kunye isinxibelelanisi Inxalenye efanelekileyo. 211039
Ingqiniba yomkhuhlane 90° Inxalenye efanelekileyo. 203130	Ingqiniba yomkhuhlane 45° Inxalenye efanelekileyo. 203131	Uphahla lwekhola yemozulu Inxalenye efanelekileyo. 152258	Uphahla lwekhola yemozulu Inxalenye efanelekileyo. 152259

ISILUMKISO:

• Kubalulekile ukuba iimveliso zokutsha azikwazi ukungena kwakhona kwisakhiwo
• Itheminali yeflue kufuneka isoloko inendlela yokungena simahla.

ISILUMKO:

• Iindawo ezimhlophe zombhobho kufuneka zingabonakali ngaphandle.
• Fakela unogada wetheminali weflue apho itheminali yeflue ingaphantsi kweemitha ezi-2 ngaphezu kweqonga apho abantu banokuhamba okanye badibane netheminali.
• Amanzi kuphela kwesithambiso esivumelekileyo sokudibanisa i-flue.

2.8 IMIPHUMELA KUNYE NENDAWO – IYAQHUBEKA
Icandelo lesi-2 - Ukufakwa kweFlue

B = Ukucoca okuphezulu
Top Clearance ngumlinganiselo ukusuka phezulu turret ukuya phezulu umngxuma apho flue iphela.
L = Ubude beflue obusebenzayo.
Ubude obusebenzayo bombhobho bulinganiswa ukusuka kumda we-turret ukuya kumlebe we-flue terminal.
Iinkqubo zombhobho ezifuna izixhobo zokwandisa kufuneka zifakelwe ngokuncipha kwe-1.5 ° ukusuka kwitheminali yombane ubuyela kwibhoyila.
Ukuhla nge-1.5 ° kunokufezekiswa ngokuyila umbhobho ngokunyuka kwe-26 mm ngemitha ubude bombhobho.
INGCACISO EBALULEKILEYO
Faka iflue ngokuhambelana ne-BS 5440:1 2008
Misa i-terminal, ngoko ke iimveliso zokutsha azibangeli inkathazo.
Umbhobho ophumayo kufuneka ungabi kufutshane ne-25 mm kwizinto ezinokutsha.
I-flue ikhuselwe eludongeni usebenzisa isanti kunye nesamente okanye i-silicone yokufudumala.
Iflue kufuneka ixhaswe sisibiyeli kwimitha nganye yobude beflue kwaye kulo lonke utshintsho lwecala. Imibhobho efihliweyo kufuneka ibe nezikhewu zokuhlola ezingekho ngaphezu kwe-1.5 yeemitha ukusuka kumalungu.
Apho kunokwenzeka izikhewu zokuhlola kufuneka zibekwe kwindawo etshintshayo yezalathiso. Apho oku kungenzekiyo kufuneka kugobe viewekwaziyo macala omabini. Izikhewu zokuhlola kufuneka zibe yi-300 mm² ubuncinane

Ukuthe tye	UBona Ubude boMbane obusebenzayo
24 kW	9.0 yeemitha
30 kW	8.0 yeemitha
35 kW	6.0 yeemitha
Ngokuthe nkqo
24/30/35 kW	7.5 yeemitha
Ingqiniba zonyusa ukuxhathisa kwaye zibenobude obulinganayo beflue. Le theyibhile ilandelayo yi example.
Inxalenye	x	Ukuchasa
45° ingqiniba	2	1.2 yeemitha
90° ingqiniba	2	2.0 yeemitha
Ubude beflue obusebenzayo		3.2 yeemitha

Flue Terminal Izikhundla	Min. Isithuba*
1.Ngqo ngezantsi, ngaphezulu okanye ecaleni kwendawo evulekileyo.	300 mm
2.Ngaphantsi kwe-guttering, i-drain mibhobho okanye imibhobho yomhlaba.	75 mm 25 mm*
3.Ngaphantsi kwe-eves.	200 mm 25 mm*
4.Ngaphantsi kweebhalkhoni okanye uphahla lwe-port yemoto.	200 mm 25 mm*
5.Ukusuka kwimibhobho yokucoca ngokuthe nkqo okanye imibhobho yomhlaba.	150 mm 25 mm*
6.Ukusuka kwikona yangaphakathi okanye yangaphandle okanye a Umda ecaleni kwetheminali.	300 mm 25 mm*
7.Ngaphezu komhlaba omeleneyo, uphahla okanye umgangatho webalcony.	300 mm
8.Ukusuka kumphezulu okanye kumda ojongene netheminali.	600 mm
9.Ukusuka kwitheminali ejongene netheminali.	1200 mm
10.Ukusuka ekuvulekeni kwizibuko lemoto ukuya kwindawo yokuhlala.	1200 mm
11.Ngokuthe nkqo ukusuka kwitheminali kudonga olufanayo.	1500 mm
12.Ngokuthe tye ukusuka eludongeni lwetheminali.	300 mm
13.Ngokuthe tye ukusuka kwifestile emeleneyo	600 mm
14.Ukujonga indawo yokuvula kwisakhiwo esisecaleni	2000 mm
15.Kwi-engile kumda 90° 45°	300 mm 600 mm
16.Ukungqamana nomda	300 mm
17.Ngaphantsi kwenqanaba lomhlaba - vula ukukhanya kakuhle a) Ngaphantsi komhlaba b) Ngaphezulu komgangatho c) Ukusuka ecaleni d) Ukusuka kumphezulu wobuso	<1,000 mm 300 mm 300 mm 600 mm
*Kunye kuphela ukucutha ukuya kutsho kwi-25mm okuvumelekileyo ngofakelo ngalunye.

2.9 IINDAWO EZINGXOXILEYO ZEFLUE

2.10 IINDAWO EZINGQONGILEYO

2.11 IMILINGO YENKQUBO YEFLUE
Uyilo lweFlue
OKUBALULEKILEYO:

1. Ubude beflue bunokwahluka, soloko ulinganisa ubude beflue phambi kokusikwa.
2. Ubude bombhobho obusebenzayo kunye nobude bokwenene bombhobho yimilinganiselo eyahlukileyo.
3. Ubude be-flue obusebenzayo wenziwe ngokulingana nobude be-flue kunye namacandelo e-flue phakathi kwe-turret, i-elbows kunye ne-terminal.
4. Ubude beflue obuyinyani bubungakanani bombhobho ofunekayo ukufikelela kubude obusebenzayo beflue, oku kubandakanya ufakelo.

Inxalenye	Ubude Obubo	Ukufakwa	Ubude obusebenzayo
1 m ubude bomkhuhlane	1 m	30 mm	970 mm
1 m ubude bomkhuhlane	1 m	30 mm	970 mm
0.6 m flue terminal	0.6 m	30 mm	570 mm
Iyonke	2.6 m	90 mm	2510 mm

2.12 UKUFAKA I-TURRET

1. Qinisekisa ukuba i-condensate trap izaliswe ngamanzi
2. Qinisekisa ukuba isitywini serabha asonakaliswanga kwaye sifakwe ngokuchanekileyo kwisininzi sesixhobo.
3. Bamba ngokuqinileyo iflue kwaye utyhale i-turret ide ihambe i-30 mm uqinisekise ukuba umkhuhlane awujikelezi okanye uye phambili.
4. Tyhiliza i-turret kwi-manifold uqinisekise ukuba umlebe ongentla weplastiki ugungxulwa ngomphezulu we-manifold.
5. Zibandakanye ngokupheleleyo neclamp icandelo lendawo kumngxunya weendawo ezininzi kwaye ujikelezise ezantsi kwiflange.
6. Sebenzisa izikrufu zokukhusela ukukhusela i-clamp kwisixhobo.
7. Qinisekisa zonke sample amanqaku ziyafikeleleka kwaye zonke sampiiplagi kunye neekepusi zifakiwe.

2.13 UKUSIKA UMHLABA
UKUSIKA UFLUE OWENZAYO (engezizo telescopic)

1. Linganisa ubude obufunekayo bombhobho (A + 44 mm)
2. Ukulinganisa ukusuka kumlebe wesiphelo ukuya ekupheleni kombhobho ongaphandle. Phawula ubude obufunekayo bokusika (A + 44 mm) malunga nesangqa setyhubhu yangaphandle kwaye usike ngokulandela uphawu ukuqinisekisa ukuba sisikwe isikwere.
3. Phawula kwaye unqumle ityhubhu yangaphakathi i-10 mm ubude kunetyhubhu yangaphandle qinisekisa ukuba ukusika kusikweri.
4. Susa zonke ii-burrs kwityhubhu yangaphakathi nangaphandle kwaye ubeke i-chamfer ekhanyayo kwityhubhu yangaphakathi ukunceda ukuhlanganisa.

UKUBEKA UFLUE WETELESKOPI

1. Ukulinganisa ubude obufunekayo (A + 44 mm)
2. Tsala i-flue ngaphandle kude kube ubude obufunekayo bufezekisiwe uqinisekise ukuba uphawu lokumisa alubonakali.
3. Qinisekisa ukuba zombini i-flue seams ingaphezulu kwaye i-terminal ye-flue outlet iphezulu kakhulu.
4. Gqoka umngxuma oyi-3.5 mm kwityhubhu encinci nenkulu yangaphandle usebenzisa umngxuma wokulinga kwityhubhu enkulu yangaphandle.
5. Khusela ityhubhu yangaphandle enkulu kunye encinci usebenzisa izikrufu ezinikiweyo.
6. Vala umdibaniso kumbhobho ongaphandle ngeteyiphu enikiweyo.
7. Faka amatywina odonga lwangaphakathi nangaphandle.

UKUFAKA I-FLUE NGIYA UDONGA (UFakelo lwangaphakathi)

1. Ukulinganisa ubukhulu bodonga.
2. Kulo mlinganiso wongeza i-14 mm.
3. Yenza uphawu kwiflue eboniswe njengophawu 1 (phezulu ekunene).
4. Yenza olunye uphawu kwiflue enye i-14 mm eboniswe njengoPhawu 2 ngasentla ngasekunene.
5. Faka itywina eludongeni lwangaphandle (olumnyama) kwitheminali yeflue uqinisekise ukuba ifakelwe kwitheminali yotywino lomlebe wangaphandle.
6. Faka itywina elingaphakathi eludongeni malunga ne-65 mm ngaphambi kophawu lwesi-2.
7. Beka isiphelo sesiphelo sombhobho kumbindi we-127 mm owombiweyo embindini kwaye ngokucothayo faka uxinzelelo oluncinci kwaye usethe umbhobho uwunyuse okanye ezantsi okanye icala ukuya kwelinye. Oku kuya kubangela
   isitywina sangaphandle sodonga ukuba sisonge kwaye sivumele i-flue ukuba idlule eludongeni.
8. Xa itywina elingaphakathi eludongeni ligungxulwa eludongeni tsala umva iflue de iMark 1 igungxulwe nomphezulu wodonga lwangaphakathi.
9. Bamba i-flue ngokuthe nkqi kwaye utyhale itywina langaphakathi eludongeni kude kube ngumqondiso we-2 obonakalayo.

UKUFAKA UMFANEKISO NGODONDA
(Ufakelo lwangaphandle)

1. Landela amanyathelo 1 – 5 ukusuka phezulu.
2. Tyhiliza umbhobho kumngxuma ombindiweyo oyi-127 mm ukusuka ngaphandle
3. Buyela ngaphakathi kwipropathi kwaye ulungele udonga lwangaphakathi lwetywina kwi-flue.
4. Tsala iflue ngaphakathi de iMark 1 igungxulwe nomphezulu wodonga lwangaphakathi.
5. Ukubamba i-flue kule ndawo tyhala itywina langaphakathi eludongeni kude kube nguMarko 2 obonakalayo.

Ukuba i-Mark 1 ayigungxulwanga kunye nomphezulu wodonga lwangaphakathi kwaye inokubonwa ngaphambi kodonga, ngoko itywina lwangaphandle luza kube lukhutshiwe kwaye luya kufuna ukuphinda lufakwe. Ukuba le meko iyenzeka, ngoko nceda uqale inkqubo ukusuka ekuqaleni.
Ekugqityweni iflue iya kufakwa ngokuchanekileyo njengalapha ngezantsi.

OKUBALULEKILEYO: Qinisekisa ukuba akukho flue emhlophe ibonakala phakathi kwetheminali yeflue kunye nodonga.
Ividiyo ebonisa indlela yokulinganisa ngokuchanekileyo kunye nokulingana iflue inokufunyanwa ngokuskena iKhowudi yeQR.

https://idealheating.com/logic-V4-literature-9

Kuluhlu olupheleleyo lwe UFLUE NEZIBONELELO Nceda undwendwele idealheating.com/flues

https://idealheating.com/logic-V4-literature-1

2.14 UKUHLANGANISA UMFANEKISO OQONDILE
Qinisekisa ubude obuchanekileyo ukuba i-flue kufuneka iphele ngaphezu kophahla. Ukuba emva kokubala okanye ukulinganisa ubude bombhobho bubonke ukusuka phezulu kwibhoyila, kuyafuneka ukusika yomibini imibhobho yendibano A, emva koko uqiniseke ukuba isikwe ngokulinganayo ishiya ityhubhu yeflue yangaphakathi inde kunombhobho womoya wangaphandle njengoko unikezelwe.
Qinisekisa ukuba iziphelo zombhobho osikiweyo zikhululekile kuzo naziphi na ii-burrs.

1. Beka ipleyiti edanyazayo eluphahleni (enikezelwe ngokwahlukileyo) phezu komngxuma osikwe eluphahleni kwaye ufake i-terminal flue ukusuka ekupheleni kophahla.
2. Faka isinxibelelanisi esithe nkqo (esinikezelwe kwikhithi) ngokuhambelana nemiyalelo enikiweyo.
3. Khusela isidibaniso esithe nkqo ngokufaka uxinzelelo olusezantsi kwikhonkco.
4. Beka i-clamp kubuso obuphezulu be-flue manifold kwaye uyityhale ngokuthe tye ngasemva. Khangela zombini clamp i-lugs kwi-flue manifold kwaye ikhuselekile kwi-flue manifold kunye ne-M5 egcina isikrufu.
5. Push umbhobho wolwandiso (ukuba uyafuneka (ubonelelwe ngokwahlukeneyo)) kwisidibanisi esithe nkqo.
   Phawula. Qinisekisa i-turret sampAmanqaku ayasebenza kwaye zonke iicap kunye neeplagi zifakelwe. Gcwalisa i-condense trap / siphon ngamanzi.
6. Ukuba umbhobho wokugqibela wokwandisa ufuna ukusika, linganisa u-'X', umgama phakathi kombhobho (ongaphandle) kunye netheminali, kwaye udibanise i-100 mm kulo mlinganiso. Oku kunika ubude bombhobho wokugqibela wokwandisa. Phawula. Qwalasela indawo ome kuyo umbhobho weflue wangaphakathi xa uthelekiswa nombhobho wangaphandle kumbhobho (imibhobho) odityanisiweyo kwaye uqinisekise ukuba umbhobho wesiphelo sombhobho weflue usikwe ixesha elide kunombhobho womoya ukuqinisekisa ukubandakanyeka kwitywina lokugqibela lombhobho weflue.
7. Ekugqibeleni qinisekisa ukuba ipleyiti edanyazayo yophahla ivalwe ngokuchanekileyo eluphahleni.

2.15 I-CONNDENSATION RAIN

Esi sixhobo sifakelwe isixokelelwano se-symphonic 75 mm condensate trap efuna ukuzaliswa ngaphambi kokusebenza isixhobo okokuqala okanye emva kokugcinwa.
Yonke imibhobho yecondensate kufuneka ihambelane noku kulandelayo:
a. Apho kufakelwe ibhoyila entsha okanye efakelwayo, ufikelelo ‘kwibhoyila ekhuphayo’ yangaphakathi kufuneka ibe yenye yezinto eziphambili eziqwalaselwayo ekumiseleni indawo yebhoyila.
b. Iplastiki ene-push fit okanye i-solvent connections.
c. Umbhobho weplastiki wangaphakathi usebenza ubuncinane be-ID ye-19 mm (ngokuqhelekileyo i-22 mm OD).
d. Umbhobho weplastiki wangaphandle kufuneka ubuncinane ube yi-ID eyi-30 mm (ngokuqhelekileyo yi-32 mm OD) phambi kokuba udlule kudonga olunemikhono.
e. Yonke imibhobho exwesileyo kufuneka iwe ubuncinane obuyi-52 mm ngemitha ukusuka kwiBoiler.
f. Imibhobho yangaphandle kunye nengafudumeziyo kufuneka igcinwe incinci kwaye igqunywe ngeKlasi "O" yokugqunywa kwemibhobho egqunywe ngumkhenkce okanye ngenye indlela.
g. Zonke iifakelo kufuneka zenziwe ngokuhambelana neendlela ezifanelekileyo zokudibanisa njengoko kuboniswe "kwimizobo yokufakela i-Condensate" & BS6798.
h. Imibhobho kufuneka ifakwe ukuze ingavumeli ukuchitheka kwindawo yokuhlala xa kuthe kwavaleka (ngokukhenkceza)
i. Zonke ii-burrs zangaphakathi kufuneka zisuswe kumsebenzi wombhobho kunye naluphi na ukufakwa.
Ukuze unciphise umngcipheko wokuba ngumkhenkce, cima umbhobho wokuhambisa amanzi nge-condensate usebenzisa enye yezi ndlela zilandelayo:
Udibaniso loMbhobho wangaphakathi
Hambisa umbhobho wecondensate ngomxhuzulane ukuya kwindawo engaphakathi, emdaka yokukhupha amanzi.Impompo yeCondensate
Xa kungenzeki ukuphelisa umbhobho wecondensate ukuya kwindawo yokukhupha amanzi amdaka angaphakathi usebenzisa umxhuzulane, sebenzisa impompo efanelekileyo ekhuthazwa yibhoyila okanye impompo.
umenzi.

Udibaniso lweDrain lwangaphandle
Ukusetyenziswa kombhobho we-condensate oqhutywa ngaphandle kufuneka kuqwalaselwe kuphela emva kokuphelisa zonke iinketho zokuphelisa ngaphakathi njengoko kuchaziwe ngaphambili. Inkqubo yangaphandle kufuneka iphele kwindawo efanelekileyo yokukhupha amanzi amdaka okanye injongo eyenzelwe ukufunxwa. Ukuba inkqubo yangaphandle ikhethiwe ngoko ke le milinganiselo ilandelayo kufuneka yamkelwe: Ukuhamba kombhobho wangaphandle kufuneka kugcinwe kuncinci kusetyenziswa eyona ndlela ichanekileyo kunye "eyona nto iphakamileyo" ukuya kwindawo yokukhupha, kungabikho macandelo anqamlekileyo apho i-condensate ingaqokelela khona.

• Ukudibanisa kumhlaba wangaphandle / isitaki sokuphuma. Amanyathelo okugquma njengoko kuchaziwe kufuneka asetyenziswe.
• Xa kusetyenziswa umbhobho wamanzi emvula, kufuneka kufakwe isithintelo somoya phakathi kombhobho wokuhambisa amanzi ejiyile kunye nombhobho osezantsi ukuze kuthintelwe ukubuya umva kwamanzi emvula kwibhoyila xa umbhobho ukhukulisekile okanye umkhenkce.
• Apho umbhobho wombhobho wecondensate uyekeliswa ngenjongo eyilelwe ukuba manziswe (jonga ku-BS 6798) nawaphi na amacandelo ombhobho odityanisiweyo ongaphezulu komhlaba kufuneka aqhutywe kwaye agqunywe njengoko kuchaziwe ngasentla.
• Apho umbhobho wokukhupha amanzi omdaka uphela kumjelo omdaka ovulekileyo okanye umjelo, umbhobho kufuneka uphele ngaphantsi kwenqanaba lokugalela, kodwa ngaphezu komgangatho wamanzi, ukunciphisa “ingqele yomoya” kwindawo evulekileyo. Ukusetyenziswa kwesigqubuthelo sombhobho (njengoko sisetyenziswa ukunqanda ukuvaleka ngamagqabi) kunokubonelela ngothintelo olungaphaya kwingqele yomoya.

IiNdawo zangaphakathi ezingatshisiyo
Imibhobho yokuhambisa amanzi angaphakathi asebenza kwiindawo ezingafudunyezwanga, umz. amagumbi angaphantsi komhlaba kunye neegaraji, kufuneka aphathwe njengombhobho wangaphandle.
Qinisekisa ukuba umthengi uyayazi imiphumo eyenziwe yi-condensate enomkhenkce kwaye ibonisiwe apho olu lwazi lunokufumaneka khona kwincwadi yomsebenzisi.
Phawula. Nceda ujonge isikhokelo sangoku se-HHIC sokukhutshwa kwe-condensate ekhoyo ngoLuhlu lweeBulletin zobuGcisa eziBhalisiweyo eziKhuselekileyo. Hayi isiIrish
Umzobo 1 – Ukudityaniswa koMbhobho woMbhobho weCondensate kuMhlaba waNgaphakathi kunye neSitaki seVent

Umzobo 2 – Ukudityaniswa koMbhobho woGutyulo weMijelo eMazantsi eSinki, iBasyini, iBhafu okanye iSiteyi saManzi seShawari kwisitampu seVenti yoMhlaba yaNgaphakathi

Umzobo 3 –Uqhagamshelo lweMpompo yeCondensate yeNdlela yoQeqesho (jonga imiyalelo eneenkcukacha zomenzi)

Umzobo 4 – Ukudityaniswa koMbhobho woMbhobho weCondensate kuMhlaba waNgaphandle kunye neSitaphu seVent

Umzobo 5 – Ukudityaniswa koMbhobho wokuGutyula iCondensate kuMbhobho waNgaphandle waManzi emvula (kuphela adityanisiweyo amdaka/amanzi emvula)

Umzobo 6 – Ukudityaniswa koMbhobho woMbhobho weCondensate kwiNjongo yaNgaphandle Eyenziwe yaSoka.

2.17 UQHAGAMSHELO NOKUZALISWA

ISILUMKO: Ukufudumeza iivalvu zokwahlula kungonakalisa iifiber seals
Lungelelanisa umanyano ngalunye kunye nezitywina zefiber ezibonelelweyo.
UQHAGAMSHELWANO LWAMANZI CH

1. Qhagamshela i-CH yenkonzo yokuhamba kwevalve (umqheba omnyama) kunye nomsila wobhedu onikezelwe kwipakethe yehardware ukuya kuqhagamshelo lweboss ephothiweyo olubonelelwe ngasemva kwibhoyila.
2. Xhuma i-valve yokubuyisela i-CH (isiphatho esimnyama) kunye nomsila wobhedu.

KUBALULEKILEYO Faka i-Ideal system filter ngokwenkqubo yofakelo kunye nesikhokelo sokugcina. Ukungaphumeleli ukufaka isihluzi senkqubo ngokuchanekileyo kuya kuchaphazela iwaranti yebhoyila.
UQHAGAMSHELWANO LWAMANZI I-DHW

1. Faka ivalve yenkonzo yokungena ye-DHW (isiphatho esibhlowu) kunye nomsila wobhedu kumdibaniso odityanisiweyo weboss ukuqinisekisa ukuba isitywina esinikiweyo sibekwe ngokuchanekileyo.
2. Faka umbhobho ophumayo we-DHW kuqhagamshelo lwe-DHW, uqinisekise ukuba isitywina esibonelelweyo sibekwe ngokuchanekileyo.
3. Faka i-loop yokuzalisa ebonelelwe phakathi kwe-valve yokungena ye-DHW kunye ne-CH valve yokubuya.

ISILUMKO: I-cock yenkonzo yegesi ivalwe nge-non-metallic blue fiber washer, ekungafuneki ukuba ishushu kakhulu xa idibanisa i-capillary.
UQHAGAMSHELO LWEGAS
Ngeenkcukacha zendawo yoqhagamshelo lwegesi:

Izinga lokuhamba kwamanzi ashushu asekhaya lilawulwa ngokuzenzekelayo ukuya kubuninzi:

kW	L/m	gpm
24	9.9	2.2
30	12.4	2.8
35	14.5	3.2

I-PRV DRAIN
Uqhagamshelo lwe-PRV, olukwicala elisezantsi lasekhohlo kwibhoyila, liquka igrommet evuliweyo.
KUBALULEKILEYO
I-grommet yenzelwe i-15 mm Ø ipayipi yobhedu.
Ukuba kunokwenzeka, hlanganisa kwangaphambili kwaye uthengise umbhobho ngaphambi kokuFakela.
Ukuba oku akunakwenzeka, i-soldering kufuneka ibe ngaphezu kwe-100 mm kude ne-grommet. Qinisekisa ukuba i-grommet ayonakaliswanga ngubushushu.
Faka umbhobho wecondensate ngolu hlobo lulandelayo:

1. Qinisekisa ukuba umbhobho wobhedu we-15 mm Ø unqunywe ngokuthe ngqo kumbhobho.
2. Qinisekisa ukuba umbhobho awonakali, kwaye ucoceke kwaye ukhululekile kwiibhubhu.
3. Ukusebenzisa iipliers beka ikliphu phezu kwegrommet. Qhubeka ubambe ikliphu uyivule.https://idealheating.com/logic-V4-literature-10
   Phawula. Musa ukukhulula ikliphu kude kube yinyathelo lesi-5 (jonga ngezantsi).
4. Gcoba umbhobho wobhedu kwi-grommet (ubuncinci be-15 mm). Qinisekisa ukuba umbhobho uhambelana ne-grommet.
5. Ngezantsi uphawu lokumisa kwi-grommet vula iipliers ukukhulula ikliphu.
6. Qinisekisa ukuba ikliphu kunye nombhobho ziqhotyoshelwe ngokuchanekileyo.
7. Qinisekisa ukuba i-PRV yokukhupha ipayipi ifakwe ngokuchanekileyo. Qinisekisa ukuba i-angle ye-pipe run yanele ukususa amanzi akhutshiweyo.

ISILUMKISO:
Qinisekisa ukuba amanzi okanye umphunga (osuka kwibhoyila) ukhutshwa ngokukhuselekileyo. Amanzi ashushu okanye umphunga unobungozi kwaye unokubangela ukwenzakala okukhulu, kunye nomonakalo kwiinkqubo zombane.

Injongo eyenziwe umbhobho wokukhupha i-PRV unikezelwa ngebhoyila ukuvumela ukukhutshwa okukhuselekileyo ngodonga ukuya ngaphandle kwesakhiwo. Oku kubaluleke ngakumbi kufakelo 'lokunyuka okuphezulu' kodwa lunokusetyenziswa kulo lonke ufakelo.

UKUZALISA
ISILUMKISO: Khusela uqhagamshelo lombane emanzini

1. Xhuma i-loop yokuzalisa, uqinisekise ukuba ii-washers zikhona.
2. Khulula ikepusi yothuli yokukhupha umoya.
3. Khangela ezi ziphatho zilandelayo zokwahlula kuqhagamshelo lwamanzi zikwindawo yokuzalisa ethe tye (isiphatho esiluhlaza okwesibhakabhaka kwi-DHW inlet kunye nesiphatho esimnyama kwi-CH return C).
4. Misa isibambo sevalve yokwahlukanisa ye-CH kwindawo ethe nkqo ukuze uzalise.
5. Kancinci ujike umqheba wokuzalisa iluphu (oluhlaza B ) kwindawo evulekileyo ethe tyaba de igauji yoxinzelelo ifundeke phakathi kwe-1 ukuya kwi-1.5 bar.
6. Jika umqheba wokuzalisa iluphu (luhlaza B ) ubuyele kwindawo evaliweyo (ethe nkqo).
7. Jika i-CH Return handle (emnyama C ) kunye ne-DHW Inlet handle (blue ) kwindawo evulekileyo (ethe nkqo).
8. Nqamula i-loop yokuzalisa kwi-valve ye-DHW Inlet kwaye ulungele i-cap e-grey ekupheleni okuvulekileyo.
9. Faka iPlug ukuya ekupheleni kwamahhala kwi-loop yokuzalisa.

Ukuzalisa izithuba zeNkqubo ebonisiweyo

Gcwalisa

1. Xhuma i-loop yokuzalisa, uqinisekise ukuba ii-washers zikhona.
2. Khulula ikepusi yothuli yokukhupha umoya.
3. Jika isiphatho sokungena se-DHW (ebhlowu ) kwindawo ethe tye.
4. Kancinci ujike umqheba wokuzalisa iluphu (oluhlaza B ) kwindawo evulekileyo ethe tyaba de igauji yoxinzelelo ifundeke phakathi kwe-1 ukuya kwi-1.5 bar.
5. Jika umqheba (oluhlaza B) kwi-loop yokuzalisa ubuyele kwindawo evaliweyo (ethe nkqo).
6. Jika i-DHW Inlet handle (blue ) kwindawo evulekileyo (ethe nkqo).
7. Nqamula i-loop yokuzalisa kwi-valve ye-DHW Inlet kwaye ulungele i-cap e-grey ekupheleni okuvulekileyo.
8. Faka iPlug ukuya ekupheleni kwamahhala kwi-loop yokuzalisa.

https://idealheating.com/logic-V4-literature-2

Izikhundla eziphezulu zoxinzelelo ezibonisiweyo

2.19 UKUQHAKAMISWA KOMbane
ISILUMKISO: Esi sixhobo kufuneka senziwe umbane ongundoqo we-230 V ~ 50 Hz uyafuneka.
3 Ifuse iyafuneka. Lonke ulawulo lwangaphandle kunye neengcingo kufuneka zilungele ii-mains voltage.
Iintambo zangaphandle kwibhoyila kufuneka zilandele imimiselo yocingo ye-IEE (BS7671) yangoku kunye nemimiselo yasekuhlaleni.
I-Wiring kufuneka ibe yi-3 engundoqo ye-PVC ye-insulated cable, ingabi ngaphantsi kwe-0.75 mm 2 (24 x 0.2 mm), kunye ne-BS6500 Table 16.
Uqhagamshelo kufuneka lwenziwe ngendlela evumela ukwahlulwa ngokupheleleyo kobonelelo lombane. Iindlela zokuzihlukanisa kufuneka zifikeleleke kumsebenzisi emva kokufakwa.
2.20 IINGCACISO YOKUFAKA
ISILUMKISO: Qinisekisa ukuba intambo yonikezelo ayonakaliswanga Ibhoyila kufuneka iqhagamshelwe kunikezelo lwamandla asisigxina.
Ukufikelela kwiingcingo zokufaka

1. Yahlula umbane ongundoqo kwibhoyila.
2. Susa ipaneli yangaphambili.
3. Swayipha phantsi kwebhokisi yokulawula kwindawo yenkonzo, ucofe kwaye ujiwule umva isigqubuthelo socingo lwe-installer kwaye uqhoboshele kwiziqeshana ezigcinayo.
4. Gcoba ngononophelo i-grommet, khulula ikhebula clamp ngokusebenzisa izikrufu kwaye utsale iingcingo.
5. Qhagamshela iingcingo zangaphandle kuqhagamshelo olufanelekileyo ngokukhuselekileyo kwaye ke ulungise intambo clamp.

Emva kokuba nayiphi na i-wiring igqityiwe, ukukhusela ibhoyili, buyisela umyalelo ongentla.
Ucingo lwekhonkco kwi-230 V yegumbi lokufakela stat/uqhagamshelwano lwexesha lunika imfuno ebambisene neplagi yokukhetha isibali-xesha ngaphakathi kwesigqubuthelo sokhetho lwesibali-xesha. Le ibekwe kwi
umphambili webhokisi yolawulo.
UQhagamshelwano lwesiFakelo (LHS)…………………….UQhagamshelwano lwesiFakelo (RHS)

2.21 IINGCACISO YANGANGAPHANDLE

Ulawulo lwangaphandle - 230 V 50 Hz
I-Wiring ye-230 V ye-Programmable Room Stat (Imizobo A & C) okanye i-230 V Timer kunye ne-Stat yegumbi (Idayagram B).

1. Susa intambo yekhonkco kwistat/uqhagamshelwano lwexesha.
2. Qhagamshela intambo yangaphandle ukusuka kwistat/timer yegumbi ngapha kolu qhagamshelwano. Ukuba uqhagamshelo oluphilayo jikelele lusetyenziselwa i-stat yegumbi okanye isibali-xesha uze uqhagamshele oku kwi-fused spur, kwicala lomthwalo (jonga kwiSazobe C).
3. Ukuba i-thermostat yegumbi inembuyekezo kwaye idinga uxhumano olungathathi hlangothi, yenza olu xhulumaniso kwi-fused spur, kwicala lomthwalo.

ULawulo lwaNgaphandle oluKhethayo – uMqulu ophantsi owongezelelweyotage
I-Wiring Panther ye-Programmable Room Stat (Umzobo D).

1. Susa iplagi yekhonkco yesibali-xesha ngaphakathi kwesigqubuthelo sokhetho lwesibali-xesha, esiphambi kwebhokisi yolawulo.
2. Khipha isokethi yekhonkco lexesha ukusuka kwindawo esemva kwebhokisi yolawulo, fumana iplagi kwisebe elinye le-harness kwaye udibanise ezi kunye.
3. Ukusebenzisa i-rubber bung esecaleni kolu qhagamshelwano, yifake kwindawo evulekileyo.
4. Qhagamshela intambo yangaphandle esuka kwiPanther Programmable Room Stat kwi-RHS yoqhagamshelo lwesifakeli sebhoyila, ebhalwe OpenTherm.

Ukhuseleko lweFrost
Ukuba iinxalenye zombhobho zisebenza ngaphandle kwendlu okanye ukuba ibhoyila iya kuyekwa ixesha elingaphezu kosuku okanye njalo ngoko ke i-thermostat yeqabaka kufuneka ifakwe kwiintambo kwisixokelelwano.
Oku kuqhele ukwenziwa kumdwelisi wenkqubo, apho umkhethi wenkqubo iiswitshi zisetwa ukuba IVALIWE kwaye zonke ezinye izilawuli KUFUNEKA zishiywe kwindawo esebenzayo.
I-thermostat yeqabaka kufuneka ibekwe kwindawo ebandayo, kodwa apho inokuva ubushushu obuvela kwisixokelelwano.
Ukufaka iintambo kwisixokelelwano se-thermostat yeqabaka, jonga imizobo E. Faka iingcingo kwi-thermostat yeqabaka kuyo yonke imidibaniso emibini njengoko kubonisiwe.
Ukuba ibhoyili ifakwe kwigaraji kunokufuneka ukuba ifake i-thermostat yombhobho, ngokukhethekileyo kwi-pipework yokubuyisela.

Umzobo A: I-230 V ye-Programmable Room Stat	Umzobo B: 230 V Isibali-xesha kunye neStat seGumbi	Umzobo C: 230 V Ukusetyenziswa kweSitati segumbi okuCwangcisiweyo kokuPhila kwi-Isolator	Umzobo D: I-Panther IStat yeGumbi eLungiselelayo	Umzobo E: 230 V Ukhetho lwe-Frost Stat

2.22 I-WIRING DIAGRAM

Isitshixo
bak: Mnyama	g/y: luhlaza/mthubi
ewe: Grey	o: orenji
r: ebomvu	p: ipinki
g: luhlaza	v: violet
b: blue	y: tyheli
br: mdaka	w: mhlophe
g/y: luhlaza/mthubi

2.23 UKUTSHA TSHINTSHA IKHEBHULU EPHAMBILI EFANELEKILEYO
Ukuba kuyimfuneko ukusebenzisa enye intambo engundoqo kule ifakelwe kwangaphambili sebenzisa esi sikhokelo silandelayo.
Ukutshintshwa kwee-wiring kufuneka kuhambelane namanqaku kwaye kuqhutywe ngumntu oqeqeshiweyo.

1. Yahlula umbane ongundoqo kwibhoyila.
2. Susa ipaneli yangaphambili.
3. Swayipha ibhokisi yolawulo ezantsi kwindawo yenkonzo, ucofe kwaye ujiwule umva isigqubuthelo socingo lwe-installer ukuze ubambele kwiziqeshana ezigcinayo.
4. Khupha imidibaniso ye-LN & E kwaye ususe iingcingo kwisidibanisi.
5. Susa intambo engundoqo ngokutsala umva ngegrommet.
6. Indlela yokutshintshwa kwi-grommet kwaye uphinde udibanise.
7. Vala isigqubuthelo socingo lwe-installer uqinisekise ukuba sibekwe ngokuchanekileyo kwaye intambo igcinwa kwi-strain relief njengoko kubonisiwe.
8. Swayipha ibhokisi yolawulo ubuyele kwindawo yokusebenza kwaye ulungelelanise indawo yolawulo yangaphambili uqinisekise ukuba itywina elilungileyo lenziwe.
   Uqhagamshelo lomhlaba kufuneka lube lude kunonxibelelwano lwangoku oluthweleyo. Ukuba i-anchorage yentambo iyatyibilika, iingcingo ezithweleyo zangoku ziba mbi phambi komhlaba.

2.24 UKUTHUMELA NOKUVAVANYA
A. Ukufakwa kombane
ISILUMKISO: Iitshekhi zokhuseleko lombane kufuneka zenziwe ngumntu oqeqeshiweyo.
Gqibezela iitshekhi zokuqala zombane.
Ngokubanzi
Ukutsha kwesi sixhobo kuye kwajongwa, kwahlengahlengiswa kwaza kwacwangciswa kwangaphambili kumzi-mveliso ukuze kusetyenziswe uhlobo lwerhasi oluchazwe kwipleyiti yedatha yesixhobo.
Musa ukulungelelanisa ivalve yomlinganiselo womoya / wegesi.
Jonga oku kulandelayo:

1. Ibhoyila ifakwe ngokuhambelana nale miyalelo.
2. Ukunyaniseka kwenkqubo ye-flue kunye ne-flue seals, njengoko kuchazwe kwiCandelo loFakelo lweFlue.

Qhubeka nokubeka ibhoyila ekusebenzeni ngolu hlobo lulandelayo:

1. Jonga uxinzelelo lwegesi yokungena.
2. Cwangcisa ibhoyila ukuba isebenze ngesantya esiphezulu ngokuvula impompo eshushu ukuya kuqukuqelo olukhulu.
3. Ngebhoyila esebenza kwinqanaba eliphezulu, khangela ukuba uxinzelelo lwegesi olusebenzayo kwindawo yokuhlola uxinzelelo lwegesi yokungena ihambelana neemfuno.
4. Qinisekisa ukuba olu xinzelelo lwe-inlet lunokufumaneka kunye nazo zonke ezinye izixhobo zegesi kwipropati esebenzayo.

B. Ukufakwa kwegesi
ISILUMKISO: Vula iifestile, iingcango kunye nokucima amadangatye ngaphambi kokuba uqale amanyathelo alandelayo. Musa ukutshaya.

1. Ukufakwa kwegesi yonke, kubandakanywa imitha, kufuneka ihlolwe kwaye ivavanywe ukuqina kwaye ihlanjululwe ngokuhambelana neziphakamiso ze-BS.6891.
2. Ukucoca umoya kufakelo lwegesi ngeendlela ezivunyiweyo kuphela.

OKUBALULEKILEYO: Umqathango wewaranti yomenzi kukuba inkqubo yokumisela iBenchmark igqityiwe. Iflowu tshati inikwe kwiphepha 67.
2.25 UKUKHANYA OKUQALA
Intsomi

A. Iqhosha lobushushu laManzi asekhaya ashushu	I. Gas Service Cock
B. IKnobhu yoBubushushu obuphakathi	IValve yokuNgena ye-J. DHW
C. Izitshixo ezishushu	K. CH Buyisela iValve yokwahlula
D. Ukuboniswa koBume beBoiler	L. DHW Outlet
E. Burner On isalathisi	M. Ukuzalisa iValve yeLoop
G. CH Flow Ivalufa yokwahlula	N. Umlinganiselo woxinzelelo
H. Indawo yoVavanyo loxinzelelo lokungena kwegesi

ISILUMKO: Musa ukusebenzisa isixhobo phambi kokuba sikhutshwe umoya ngokupheleleyo. Ukuba kuyimfuneko ukusebenzisa impompo, yenza njalo nge-cock yenkonzo yegesi icinyiwe.

Ibhoyila ibandakanya umjikelo we-fan overrun cycle ekufuneke ungaphazanyiswa kukwahlulwa kobonelelo lombane.

1. Khangela ukuba isixokelelwano sigcwalisiwe kwaye ibhoyila ayivalwanga emoyeni.
2. Qinisekisa ukuba isivalo somoya esizenzekelayo sivuliwe.
3. Hlaziya indawo yokusebenzela engaphambili.
4. Khangela ukuba umqhagi we-drain uvaliwe kwaye i-CH kunye ne-DHW iivalvu zokuzahlula (G,K & J) ZIVULEKILE.
5. Cinezela i Modi iqhosha de kuboniswe umnqamlezo uhamba zombini impompo kunye nee icon zeradiyetha (i-boiler icinyiwe).
6. Cima unikezelo lombane.
7. Khangela ukuba inkuku yenkonzo yerhasi (I) IVULIWE.
8. Yehlisa isikrufu kwindawo yovavanyo loxinzelelo lokungena (H) kwaye uqhagamshele igeyiji yoxinzelelo lwegesi ngombhobho obhetyebhetye.
9. Tshintsha unikezelo lombane ON kwaye ujonge zonke ulawulo lwangaphandle zibiza ubushushu.
   UBUSHUSHU BASESIPHAKATHINI
10. Cofa iqhosha leNdlela (C) de akusekho mnqamlezo ngomfanekiso weRadiator. Jika iKnobhu yoBubushushu obuseMbindini ngokwewotshi kude kube yithagethi ye-80°C
    ibonisiwe. Ulawulo lwebhoyila ngoku luya kudlula ngokulandelelana kwayo kokutshisa kude kube yilapho isitshisi sisekwe.
11. Ukuba ibhoyila ayikhanyi ke emva kwemizamo emi-5 ibhoyila iya kuvala ngaphandle kwaye ibonise “Ignition Lockout”. Cofa iqhosha lokuQalisa kwakhona. Ibhoyili iya kuphinda ukulandelelana kwayo kokutshisa. Ukuba Ukuqalisa kwakhona kwenzeka izihlandlo ezi-5 ngaphakathi kwemizuzu eli-15 emva koko “Ukuqalisa Kakhulu Kakhulu” kuya kuboniswa.
    Xa isitshisi sisekiwe isimboli somlilo (E) siya kuboniswa kumboniso kwaye iqondo lobushushu langoku liya kuboniswa kumanani amakhulu ngaphantsi kwesimboli yeradiyetha.;
    AMANZI atshisayo asekhaya
12. Ngokudubula kwebhoyila, jikelisa i-DHW Temp Knob (A) ngokwewotshi kude kube kubonisiwe ithagethi ye-65°C kwaye uvule ngokupheleleyo impompo ye-DHW. Ibhoyila kufuneka iqhubeke nokusebenza kwaye iqondo lobushushu leDHW langoku liza kuboniswa kumanani amakhulu ngaphantsi kwesimboli yempompo.
13. Qinisekisa ukuba ngokusebenza kwebhoyili, uxinzelelo lwegesi oluguquguqukayo luyakwazi ukufumana imveliso ephezulu. KUBALULEKILEYO Igalelo legesi kwi-burner lilawulwa yi-valve yegesi ngokuhambelana nokuhamba komoya okuveliswa ngumqhubi. AKUKHO umsebenzisi-uhlengahlengiso. Nakuphi na ukuphazamiseka kwisethingi etywiniweyo kwivalve yegesi kuya kuchaphazela kakubi ukusebenza kunye nokwenza iwaranti yethu ingabikho.
14. Cima itephu yeDHW.
15. Susa igeyiji yoxinzelelo lwegesi, qinisa indawo yokuvavanya uxinzelelo kwaye ujonge ukuqina kwegesi.

2.26 IKOMISHINI YE-USERFACE
Xa ibhoyila inikwe amandla okokuqala, uya kuba nokukhetha ukuseta iinkcukacha zoqhagamshelwano kwibhoyila kunye nokukhupha inkqubo.

2.27 UKUTSHINTSHA INDLELA YOKUSEBENZA KWEBHAYIBHILE
Imowudi yebhoyila iboniswa ngokungagqibekanga, ukutshintsha imo, cinezela nje imowudi kwaye ukhethe imowudi oyifunayo.

2.28 UKUSEBENZA KWE-PREHEAT
Ukushisa kwangaphambili kuya kwenzeka xa ukuhamba kweqondo lokushisa kwehla kwi-15 ° C ngaphantsi kwethagethi yeDHW.
Kuya kuqhuba de iqondo lokushisa lifike kwi-5 ° C ngaphantsi kwethagethi yeDHW okanye kude kube yimizuzu emi-3 idlule.
Umsebenzi wokutshisa kwangaphambili uya kuqhuba kuphela ubuninzi bexesha elide kwimizuzu engama-30.

2.29 UMSEBENZI WOKUPHAKATHISA NGOBUCHULE
Ukuba i-Preheat itshintshelwe kwi-Timed ngoko ukushisa kwangaphambili kuya kwenzeka kuphela xa kuyimfuneko, kunokuba lonke ixesha. Ibhoyila ifunda ipateni yosetyenziso lweDHW ngaphezulu kweveki emva koko
amaxesha i-DHW preheat ukuba isebenze kuphela ngexesha lokusetyenziswa ukusuka kwiveki edlulileyo.
Oku kuphucula isantya sokuphendula kwi-DHW ngelixa kunciphisa ukusetyenziswa kwegesi.

2.30 UKUSEBENZA KWEMENU
Imenyu iqulathe uluhlu lweempawu ezibonisa imeko yokusebenza yebhoyila. Umfaki kufuneka uskrolele ezantsi imenyu kwaye ucinezele u-enter ukukhetha ukhetho olufunekayo.

Phawula. KwiNdawo yeDiverter Valve Mid, cofa ezantsi de ibe yindawo ephakathi iqaqambile.
2.31
Esona sikhulu seDHW kunye neRayithi esezantsi inokufikelelwa ngokhetho lwemenyu.

Ibhoyila iya kuqhuba ngeRate ye-DHW ephezulu kangange-10mins ukuba kukho umthwalo owaneleyo wokupholisa

Ibhoyila iya kuqhuba ngeRate encinci ye-10mins Ukuba iqondo lokubuyisela lingaphantsi kwe-40 ° C ngoko ifeni iya kuqhuba i-30s kwizinga eliphezulu phambi kwe-r.ampukwehla ngaphezulu kwama-60 ukuya kwinqanaba elisezantsi.
Ukuba iqondo lokushisa lokubuya lingaphezulu kwe-40 ° C ngoko ifeni iya ramp phantsi ngaphezulu kwama-60 ukuya kwinqanaba elisezantsi.
2.32 IITSHEKI NGOKUBANZI
Yenza ezi zitshekisho zilandelayo ukuze usebenze ngokuchanekileyo:

1. Vula ngokupheleleyo zonke iimpompo zeDHW ngokulandelelana kwaye uqinisekise ukuba amanzi aphuma ngokukhululekileyo kuzo.
   Umboniso kufuneka ubonise:
2. Vala zonke iimpompo ngaphandle kweyona ikude kwibhoyila kwaye ujonge ukuba ibhoyila iyadubula ngesantya esiphezulu. Lo ngumzi-mveliso osetelwe ukunika ubushushu be-DHW obumalunga ne-35 oC ngokwesantya sokuhamba esixelwe kwiphepha le-10 phantsi “kokusebenza”.
3. Nciphisa izinga lokutsalwa kwe-DHW ukuya malunga ne-3 l/min (0.7 gpm) kwaye ujonge ukuba isitshixo siyamodela ukuzisa i-DHW malunga ne-65 o C.
4. Vala itephu yeDHW kwaye ujonge ukuba isitshisi esiphambili siyacima. Impompo kufuneka idlule imizuzwana engama-60. Xa impompo iyeka umboniso kufuneka ubonise:

Phawula. Kwiinkqubo ezingaphezulu koxinzelelo lwe-2 bar inlet irhuluneli yoxinzelelo lwamanzi inokufuneka ukuthintela ingxolo yamanzi.
IINDLELA ze-CH & DHW

1. Qinisekisa ukuba ulawulo lwangaphandle lwe-CH lubiza ubushushu.
2. Vula ngokupheleleyo impompo yeDHW kwaye ujonge ukuba amanzi ashushu ahanjiswa na.

Umboniso kufuneka ubonise:

Ixabiso legesi

1. Jonga izinga legesi yebhoyila xa ibhoyila ikwimveliso epheleleyo yeDHW.
2. Jonga imitha yerhasi, kungekho nasinye isixhobo esisetyenziswayo. Jonga kwiTheyibhuli 2 & 3 ukufumana amazinga egesi.
3. Vala itephu yeDHW.
4. Cwangcisa ulawulo lwangaphandle lokufudumeza olusembindini UKUVALA. I-burner kufuneka ihambe kwaye ipompo iqhubeke isebenza imizuzu emibini.
   Umboniso kufuneka ubonise:
5. Jonga ukusebenza okuchanekileyo kwesibali-xesha (ukuba sifakiwe) kunye nazo zonke ezinye izilawuli zesixokelelwano. Sebenzisa ulawulo ngalunye ngokwahlukileyo kwaye ukhangele ukuba isitshisi esiphambili siyaphendula.

INKQUBO YOKUJONGA AMANZI

1. Ngokubanda kwenkqubo, khangela ukuba uxinzelelo lokuqala luchanekile kwiimfuno zoyilo lwenkqubo. Kwiinkqubo zoxinzelelo lwangaphambili, oku kufuneka kube yi-1.0 bar.
2. Ngesixokelelwano esishushu, hlola lonke udibaniso lwamanzi ukuze ufumane isandi. Uxinzelelo lwenkqubo luya kunyuka ngokunyuka kweqondo lokushisa kodwa akufanele lidlule i-2.5 bar.
3. Njengoko inkqubo iseshushu, cima igesi, amanzi kunye nonikezelo lombane kwibhoyila kwaye ukhuphe phantsi ukugqiba inkqubo yokugungxulwa.
   Phawula. Isisombululo sokugungxulwa kufuneka sisetyenziswe ngexesha lenkqubo yokugungxula. Izisombululo zokugungxula: Fernox Super floc, Sentinel X300 (iinkqubo ezintsha) okanye i-X400 (iinkqubo ezikhoyo).
4. Gcwalisa kwakhona kwaye uvule inkqubo, yongeza i-inhibitor, cima zonke izitshixo zomoya kwaye uphinde ujonge ukuvakala kwamanzi.
5. Setha kwakhona inkqubo yoxinzelelo lokuqala kwimfuno yoyilo.
6. Lungelelanisa inkqubo.
7. Qwalasela idreyini ye-condensate xa ivuza kwaye ukhangele ukuba ikhupha ngokuchanekileyo na.
8. Ekugqibeleni, seta ulawulo kwiimfuno zoMsebenzisi.

Impompo iya kusebenza ngokufutshane njengendlela yokuzijonga kanye rhoqo kwiiyure ezingama-24 ngokungabikho kwayo nayiphi na imfuno yenkqubo.
AMANZI AMANZI
Ubushushu bunokukhethwa kusetyenziswa i-CH kunye ne-DHW thermostats.

Ukusetwa kweQhubhu lobushushu	CH UkuHamba kweTemp °C	Isixhobo se-DHW °C
Max	80	65
Min	30	40

Ngenxa yeenguqu zesistim kunye nokuguquguquka kwamaxesha onyaka amanqanaba okuhamba kwe-DHW/ubushushu bokwenyuka kuya kwahluka, kufuna uhlengahlengiso kwimpompo yokutsalwa kwempompo : okuya kusezantsi iqondo lobushushu liphezulu, ngokuphendululekileyo.
2.33 INKQUBO YOKUQALA KWAKHONA

2.34 UKUNIKEZA
Emva kokugunyazisa inkqubo, yinike umninimzi ngezi zenzo zilandelayo:

1. Nika umninimzi iMiyalelo uze uchaze iimbopheleleko zabo phantsi kwemigaqo yesizwe efanelekileyo.
2. Cacisa kwaye ubonise iinkqubo zokukhanyisa kunye nokuvala.
3. Cacisa indlela yokusebenzisa ibhoyila kunye nolawulo lwenkqubo.
4. Qinisekisa olona qoqosho lunokubakho lwamafutha oluhambelana neemfuno zekhaya zokufudumeza kunye nokusetyenziswa kwamanzi ashushu.
5. Cacisa izilumkiso eziyimfuneko zokuthintela umonakalo kwinkqubo nakwisakhiwo, kwimeko apho inkqubo ehlala ingasebenzi ngexesha leqabaka.
6. Cacisa umsebenzi kunye nokusetyenziswa kwebhoyila yokufudumeza kunye nolawulo lwamanzi ashushu asekhaya.
7. Cacisa ukuba ngenxa yokwahluka kwenkqubo kunye nokutshintsha kobushushu bamaxesha onyaka amanqanaba okuhamba kweDHW/ukunyuka kobushushu kuya kwahluka, kufuna uhlengahlengiso kwitephu yokutsalwa.
   Kuyimfuneko ke ngoko ukutsalela ingqalelo yomsebenzisi kwicandelo elikwiMiyalelo yabasebenzisi elinesihloko esithi “Ukulawulwa koBubushushu baManzi” kunye nale nkcazo ilandelayo:
   "Ukongezelela, ubushushu bunokulawulwa ngumsebenzisi ngempompo yokukhupha: isantya esisezantsi siphezulu sobushushu, kwaye ngokuphambeneyo".
8. Cacisa umsebenzi wemowudi yesiphoso sebhoyila.
9. Cacisa kwaye ubonise umsebenzi wexesha kunye nokulawula ukushisa, iivalve ze-radiator njl., ukusetyenziswa kwezoqoqosho kwenkqubo.
10. Ukuba isibali-xesha sifakiwe tsala ingqalelo kwisibali-xesha Imiyalelo yabasebenzisi uze uyinike umninimzi.
11. Cacisa ukuba igeyiji esemva kocango lokuhla, ibonisa uxinzelelo lwenkqubo yokufudumeza esembindini kwaye ukuba uxinzelelo oluqhelekileyo lwe-COLD yesixokelelwano lubonwa luhla ngexesha elithile ngoko ke ukuvuza kwamanzi kubonisiwe. Cacisa inkqubo yokuphinda ucinezele kwaye ukuba awukwazi ukuphinda ucinezele okanye ukuba uxinzelelo luqhubeka luwisa isifakeli sokufudumala sendawo esibhalisiweyo kufuneka sidibane.
12. Cacisa inkqubo yokuqalisa kwakhona ibhoyila.
13. Emva kofakelo kunye nokugunyaziswa nceda ugcwalise uLuhlu lokuQinisekisa ngaphambi kokunikezelwa kubathengi KUBALULEKILEYO
14. Inkonzo ebanzi kufuneka yenziwe ngonyaka.
    Gxininisa ukubaluleka konikezelo lwenkonzo rhoqo yiNjineli eBhalisiweyo yeGesi eKhuselekileyo.
15. Yazisa umninimzi ngewaranti yebhoyila kunye nemfuneko yokuyibhalisa ukuze ifumane inzuzo epheleleyo.

Icandelo lesi-3 – Unikezelo lwenkonzo

3.1 ISHEDYULI YENKONZO

ISILUMKISO: Inkonzo inokuqhutywa kuphela ziiNjineli eziBhalisiweyo ngeGesi eziKhuselekileyo Soloko zicima unikezelo lwerhasi kwindawo yenkonzo yerhasi, kwaye Cima kwaye uqhawule unikezelo lombane kwisixhobo phambi kokusevisa.
Uvavanyo lokutshisa kufuneka luqhutywe ngumntu onobuchule usebenzisa i-analyzer yokutshisa ehambelana ne-BS EN 50379-3: 2012.
Ukuqinisekisa ukuqhubeka nokusebenza ngokukhuselekileyo nokusebenza ngokufanelekileyo kwesixhobo sombane, kucetyiswa ukuba sikhangelwe ngamaxesha athile kwaye sinikwe inkonzo xa kuyimfuneko. Ukuphindaphindwa kwenkonzo kuya kuxhomekeka kwimeko yofakelo kunye nokusetyenziswa kodwa kufuneka kuqhutywe ubuncinane ngonyaka.
Ukuze ufumane ikopi yamva nje yoncwadi, tyelela eyethu webindawo idealheating.com.

UKUHLOLWA PHAMBILI

1. Khanyisa ibhoyila kwaye wenze uhlolo lwangaphambili, bhekisa kwitshathi yokufumana iimpazamo.
2. Qwalasela i-terminal ye-flue (kunye nonogada we-terminal ukuba ufakiwe) ngomonakalo kunye nesithintelo.
3. Jonga ukutsha ngokudibanisa i-flue gas analyzer kwi-flue gas sampling point njengoko kubonisiwe kumzobo kunye nokulinganisa i-CO kunye ne-CO2 kwinqanaba eliphezulu. Cwangcisa ibhoyila kuBuninzi kunye namagalelo obushushu obuncinci.Ukuba i-CO / CO2ratio inkulu kune-0.004 nceda uqhubeke "kwiNkqubo yokuCoca".
   Ukuba umlinganiselo we-CO / CO2 ungaphantsi kwe-0.004 nceda uqhubeke "Khangela iNkqubo".

 HLOLA INKQUBO

1. Qwalasela onke amajoyinti amanzi kunye nerhasi ngeempawu zokuvuza. Yenza kwakhona nawaphi na amalungu arhanelwayo ukuqinisekisa ukuba uxinaniso lwegesi luyenziwa ukuba luyasebenza kwaye inkqubo yamanzi iphinda izaliswe ngokuchanekileyo, ifakwe umoya kwaye iphinde icinezelwe.
2. Qhubekela kwi "KUBALULEKILE".

KUBALULEKILEYO

1. Ukuba, ngenxa yaso nasiphi na isizathu, umgibe we-condensate ususiwe, qinisekisa ukuba umgibe uhlaziywa ngamanzi ngaphambi kokuba uphinde uhlanganise.
2. Emva kokugqiba ukusevisa okanye ukutshintshiselana kwamalungu, soloko uqinisekisa ukuba zonke iivaluli zegesi ziqinile kunye nokukhangela ukuvakala kwegesi ukuya kwivalve yokulawula igesi.
3. Xa umsebenzi ugqityiwe, iphaneli yangaphambili KUFUNEKA ifakwe ngokutsha ngokuchanekileyo, ukuqinisekisa ukuba kutywinwe ngokufanelekileyo.
4. Coca isihluzi senkqubo eLungileyo, bhekisa kufakelo lwesihluzi senkqubo kunye nesikhokelo sokugcinwa kwendlela echanekileyo yonikezelo.
5. Gqibezela icandelo lenkonzo kuLuhlu lokuQinisekisa iBenchmark.

NGOKUBANZI
Ngexesha lokuSebenza, nasemva kwako nakuphi na ukulungiswa okanye utshintsho lwenxalenye yesekethe yokutsha, oku kulandelayo makutshekishwe:

• Ukunyaniseka kwenkqubo ye-flue kunye ne-flue seals.
• Ukunyaniseka kwesekethe yokutsha kwebhoyila kunye nezitywina ezifanelekileyo.
• Uxinzelelo olusebenzayo (lokusebenza) lwegesi yokungena kwizinga eliphezulu.
• Umlinganiselo werhasi.
• Ukusebenza kokutsha.

INKQUBO YOKUCOCA

1. Susa i-casing.
2. Jonga isixhobo ngokujonga iimpawu zokuvuza.
3. Susa i-flue manifold.
4. Susa ifeni.
5. Susa isitshisi.
6. Lungisa kwakhona ikhava ye sump outlet.
7. Coca isitshintshi sobushushu ngokugalela amanzi ashushu kuyo yonke i-injini yobushushu ukugungxula iidiphozithi ngononophelo ukunqanda ukugalela amanzi kwi-electrode.
8. Jonga i-electrode yomonakalo kwaye ucoce usebenzisa i-cloth e-abrasive. Jonga kwaye ulungise isithuba sentlantsi. Faka esikhundleni i-electrode ukuba yonakele.
9. Coca i-sump outlet ukuqinisekisa ukuba naluphi na ubutyobo lususiwe.
10. Susa kwaye ucoce umgibe we-condensate kwaye uphinde uqalise umgibe ngaphambi kokuba uphinde ufake.
11. Jonga isihluzo seDHW ukuba sivalekile.
12. Hlanganisa kwakhona amacandelo ngokulandelelana.
13. Coca isihluzo senkqubo Efanelekileyo. Jonga kwisixokelelwano sofakelo kunye nesikhokelo sogcino lwendlela echanekileyo yokusevisa.
14. Yenza iitshekhi zenkonzo yeposi kwisekethe yokutshisa. Jonga ngokubanzi ngezantsi.
15. Jonga umgangatho wamanzi wenkqubo ngokuhambelana ne-BS7593:2019.
16. Gcwalisa irekhodi yenkonzo kwicandelo leBenchmark.

Musa ukusebenzisa ibhoyila ukuba ipaneli yangaphambili ayifakwanga.

3.2 UKUSUSWA / UKUTSHINTSHWA KWAMACANDELO

ISILUMKISO: Musa ukusebenzisa ibhoyila ngaphandle kokufaka ipaneli yangaphambili
Xa kutshintshwa naliphi na icandelo.

1. Yahlula umbane.
2. Cima unikezelo lwegesi.
3. Susa iphaneli yebhoyila yangaphambili.
4. Swayipha ibhokisi yolawulo phantsi kwindawo yayo yokunikezela. Emva kokususa / ukutshintsha naliphi na ilungu.
5. Qinisekisa ukuba lonke uqhagamshelo lwevalvu yegesi luqinile kwaye kujongwe ukuvakala kwegesi ukuya kwivalvu yokulawula igesi.
6. Qinisekisa ukuba lonke uqhagamshelo lwamanzi luqinile.
7. Vavanya isixhobo ukuze sisebenze ngokuchanekileyo nangokukhuselekileyo.

 Amanqaku.

1. Ukunceda ekufumaneni impazamo, iphaneli yolawulo inomboniso we-LCD wokuxilonga. Isitshixo seemeko zempazamo kwibhoyila siboniswe kwiCandelo lesi-4.
2. Ukuze utshintshe amacandelo kwiCandelo 3.12, 3.15 kunye ne-3.21-3.32, kuyimfuneko ukukhupha ibhoyili.

3.3 UKUKHIPHA I-BOILER

ISETYHULA EZINGUNDOQO

1. Vala zonke i-CH iivalvu zokuhlukanisa amanzi kuzo zombini ukuhamba kunye nokubuya.
2. Ukukhupha isiphaluka sokuqala sokutshintsha ubushushu: Vula i-valve yokukhupha kwaye udibanise ubude bombhobho kwindawo ye-CH yokukhupha.
3. Emva kokutshintsha nayiphi na inxalenye kwibhoyili, susa i-hose, vala i-valve yokukhupha kwaye uvule zonke iivalve zokuhlukanisa inkqubo.
4. Ukuxinzelela ngokudibanisa kwakhona i-loop yokuzalisa, khangela ukuvuza ngaphambi kokuba uqhubeke ukujonga ukusebenza kwebhoyili.;
5. Nqamula iluphu yokuzalisa.

ISEKELA AMANZI atshisayo asekhaya

1. Vala zonke iivalvu zokwahlula zamanzi eDHW kwindawo yebhoyila.
2. Ukukhupha isekethe yamanzi ashushu asekhaya: Njengoko kungekho mjelo othe ngqo wesekethe yamanzi ashushu asekhaya, ngokuxhomekeke kwindawo yebhoyila, ukuvula eyona mpompo yamanzi ashushu iphantsi kunokukhupha le sekethi. Nangona kunjalo kufuneka kuqatshelwe ukuba amanye amanzi ayintsalela aya kukhutshwa ngexesha lokutshintshwa kwamalungu.
3. Emva kokutshintsha nayiphi na inxalenye kwibhoyila, vula ivalve yokwahlula.

3.4 UKUSUSWA KWEPANELI NGAPHAMBILI / UKUTSHAYISWA
UKUSUSA

1. Khulula izikrufu ezibini ezigcina ipaneli yangaphambili.
2. Tsala iziqeshana ezantsi ukuze ukhuphe kwaye utsale iphaneli phambili nangaphezulu kwaye uyisuse.

UTSHINTSHO
4. Haka indawo yolawulo kwiikliphu eziphezulu zokugcina.
5. Tyhila indawo yolawulo de ikliphu ezi-2 ezisezantsi zentwasahlobo zibandakanye ukuqinisekisa ukuba amaqhosha ama-2 kunye namaqhosha ama-4 ahambelana nemingxunya engaphambili.
6. Phinda uqinise izikrufu ezibini zokugcina.

3.5

1. Susa izikrufu ezibini zesigqubuthelo se-sump.
2. Susa isiciko se sump.
3. Phakamisa izinto ezininzi phezulu ukuze ucoce i-sump.
4. Shenxisa i-manifold ekhohlo kwaye utsale ezantsi ukususa.

3.6 UKUSUSWA NOKUCOCWA KWE-FAN NE-VENTURI

1. Nciphisa iintambo zombane kwifeni.
2. Susa ikliphu kwi-outlet yevalve yokulawula igesi kwaye wenze lula umbhobho ukuya phezulu. Jikelezisa emva koko lula ezantsi ukususa.
3. Susa i-nati eyandisiweyo kwisibiyeli sokufakela ifeni.
4. Phakamisa fan kunye nendibano yeVenturi.
5. Hlehlisa izikrufu ezibini ze-M4 kwaye ukhulule udibaniso lombhobho.
6. Jonga i-injector ukuba ivalekile okanye yonakele.
7. Coca umphandle we-injector kwaye usebenzise ibrashi encinci yokucoca ukucoca umngxuma wokutofa. Musa ukusebenzisa nantoni na erhabaxa njenge file.
8. Susa isikrufu kwaye ujije i-Venturi ngokunxamnye newotshi ukususa indibano ye-Venturi, uqaphela ukujongwa kwe-Venturi ngokunxulumene nomzimba wefeni.
9. Hlola i-gasket yokutywina ye-fan kwaye uyibuyisele xa kukho imfuneko.
10. Qinisekisa ukuba iVenturi ayinaluthuli/inkunkuma.
11. Khangela ii-'O'-rings zifakwe ngokuchanekileyo kumbhobho okhupha irhasi endaweni yawo ukuba kukho umonakalo othe wabonwa.

3.7 UKUSUSWA KWEZITSHI NOKUCOCWA

1. Susa izikrufu ezi-2 zokulungisa zangaphambili kunye namandongomane ama-2 angasemva awandisiweyo.
2. Phakamisa kwaye utsale phambili isitshisi ukusuka kwigumbi lokutsha ngokubamba isitshisi ngeminwe emibini kumbhobho wokungenisa umoya kunye nobhontsi wakho phezulu kwesitshisi.
3. Sikekelise isitshisi ngakuwe ukuze sinyuke siye kwindawo ethe nkqo.Phakamisa isitshisi malunga ne-5 ukuya kwi-10 mm ukusuka kwi-injini yobushushu uze utsalele phambili ngesixa esifanayo.https://idealheating.com/logic-V4-literature-3
4. Tsala isitshisi siphume kwicala lasekhohlo kwibhoyila xa sele sime nkqo.
5. Ngononophelo brasha isitshisi seceramic ngebrashi ethambileyo engeyiyo yentsimbi.

3.8 UKUCOCA I-HEAT EXCHANGER

1. Tshintsha isigqubuthelo sesump phambi kwenkqubo yokugungxulwa kwamanzi.
2. Gcoba ngokucokisekileyo umtshintshi wobushushu ngokugalela amanzi kumphezulu wegumbi lokutshisa uqinisekisa ukuba indawo epheleleyo yobushushu iyacocwa. Kuphephe ukugalela amanzi kwi-electrode.
3. Susa isigqubuthelo se-sump kwaye ucoce iidipozithi ezikhululekileyo kwi-sump.
4. Hlola i-electrode yokutshisa / ukubona. Qinisekisa ukuba icocekile kwaye ikwimeko entle – yitshintshe xa kukho imfuneko.
5. Khangela ukuba isithuba sokulayita sichanekile.

3.9 UKUBULA / UKUFUMANA UTSHINTSHO LWE-ELECTRODE / UKUHLOLWA

1. Susa ifeni.
2. Susa i-flue manifold.
3. Susa isitshisi.
4. Xa usetyenzwa kwibhoyili jonga imeko ye-electrode kwaye ujonge imilinganiselo ebonisiweyo. Ukuba kukho umonakalo kwi-electrode qhubeka ulandela amanyathelo angezantsi
   yokutshintshwa.
5. Khupha intambo yomlilo kwi-electrode.
6. Susa ilothe yomhlaba kwi-electrode.
   7. Susa izikrufu ezi-2 ezibambe i-electrode kwigumbi lokutsha.
   8. Susa i-electrode.
   9. Faka i-electrode entsha, usebenzisa i-gasket entsha enikezelweyo. Jonga imilinganiselo njengoko kubonisiwe.

3.10 UKUCOCA UMGIBE OXHUMENEYO

https://idealheating.com/logic-V4-literature-3 

1. Tsala umbhobho werabha kwi-sump drain.
2. Jika umgibe ngokwewotshi ukuze ukhuphe kwaye uphakamise ukususa.
3. Coca kwaye ugcwalise umgibe ngamanzi.

3.11

3.12 ISIHLUNGI SE-DHW & UKUCOCWA KWE-DHW FLOW/UKUTSHINTSHWA

1. Yahlula inkqubo yeDHW.
   
2. Jika i-anti yezindlu ngasekunene kwaye utsale phambili ukususa ikhatriji. Lungiselela ukukhutshwa kwamanzi athile.
3. Ukusebenzisa ipliers, khupha isihluzo seplastiki / isilawuli sokuhamba.
4. Coca okanye ufake indawo yokucoca njengoko kuyimfuneko.

3.13 ISIKHOKELO SOKUCOCWA KWENKQUBO YAPHANDLE

1. Cima ibhoyila (ubonelelo lombane lodwa).
2. Vala iivalvu zokungena/zokuphuma. Susa umazibuthe kunye ne-vent.
3. Susa ivalve yokukhupha amanzi, vula ivalve yokukhupha amanzi kunye ne-vent.
4. Vula ivalve yokungena kancinane kwaye ugungxule ngaphandle isihluzo ade abaleke amanzi.
5. Vala ivalve yokungena. Vala ivalve yokukhupha amanzi.
6. Phinda ufake umazibuthe kwaye ubeke endaweni yesivalo sevalve yokukhupha amanzi.
7. Vula iivalvu zokungena/zokuphuma, isixokelelwano sokuzalisa ngokutsha kunye nokuphuma.
8. Qalisa kwakhona ibhoyila.

3.14 UKUTSHINTSHWA KOMSHISI

https://idealheating.com/logic-V4-literature-3

3.15 IBUYISE UTSHINTSHO LWETHERMISTOR

1. Yodwa kwaye ukhuphe kwibhoyila.
2. Susa ikliphu kwizindlu zempompo kwaye ususe i-thermistor.
3. Nciphisa intambo yombane kwi-thermistor.
4. Phinda uqhagamshele isikhokelo sombane kwi-thermistor entsha kwaye udibanise kwakhona, uqinisekise ukuba i-thermistor idibene ngokupheleleyo kwaye ikliphu ibekwe ngokuchanekileyo.

3.16 UKUTSHINTSHWA KWEJENENEREYITHA YENKANTSI

1. Nqamula iintambo kwi-spark generator.
2. Tyhiliza ngobunono ijenereyitha ukukhulula ikliphu esezantsi kwisibiyeli sokunyusela ivalvu yegesi.
3. Phakamisa i-spark generator phezulu kwaye uyikhuphe kwindawo yokugcina esezantsi.
4. Faka ijenereyitha entsha yentlantsi uze uphinde udibanise, uqinisekise ukuba ilothe yomhlaba iyatshintshwa.

3.17 UKUTSHINTSHWA IVAVVU YOLAWULO LWEGAS

1. Nqamula kwaye ususe umgibe we-condensate kunye ne-rubber connector.
2. Khipha uqhagamshelo lwentambo yombane kwivalve yokulawula igesi.
3. Susa ikliphu yevalve yerhasi kwaye utyibilikise umbhobho ubheke phezulu.
4. Hlehlisa umanyano lwemibhobho yokungenisa igesi kwindawo yokungena kwivalve yegesi.
5. Hlehlisa izikrufu ezibini ezilungisa ivalve yegesi kwisiseko se-chassis kwaye uphakamisele ivalve yegesi phezulu.
6. Faka ivalve entsha yokulawula igesi uqinisekise ukuba i-'O' iringi kunye newasha yokutywina ikhona kwaye uqhagamshele kwakhona igesi noqhagamshelo lombane.
7. Lungisa umgibe.
8. Qinisekisa ukuba lonke uqhagamshelo lwevalvu yegesi luqinile kwaye kujongwe ukuvakala kwegesi ukuya kwivalvu yokulawula igesi.

3.18 UKUTshintshwa kwe-DIVERTER VALVE ACTUATOR

Ukususa injini:

1. Susa umgibe we-condensate.
2. Cinezela Phantsi kwizitshixo ezishushu de idiverter yevalve ephakathi indawo iphawulwe. Qinisekisa ukuba ivalve yokuphambukisa ikwindawo ephakathi.
3. Beka isikrudrayiva esisicaba esisicaba kwindawo ye-actuator ebonelelweyo kwaye ukhulule i-actuator.
4. Nqamula iplagi yombane kwinjini.
5. Faka i-motor entsha ukuqinisekisa ukuba ingalo ibambene ngokuchanekileyo kwifolokhwe yentsimbi kwaye iphinde idibane nokuqinisekisa ukuba isicupho secondensate sigcwaliswa kwakhona ngamanzi. Phinda uqhagamshele iplagi yombane kwinjini.

3.19 IXOXA UTSHINTSHO LOMTHETHO

ISILUMKISO: Kubalulekile ukuba ubungakanani obuchanekileyo bebhoyila kunye nohlobo lwamafutha lufakwe kwibhoyila.
ISILUMKO: Faka umtya womhlaba obonelelwe ngePCB esihlahleni sakho kwaye ukhuseleke kumhlaba ofanelekileyo kwibhoyila chassis.
3.20 UKUTSHINTSHWA KWEPCB EYINTLOKO

1. Khulula ngononophelo iziqeshana ezine ezigcinayo kwaye ususe isigqubuthelo sebhokisi yolawulo.
2. Khupha lonke uqhagamshelo olukhokelela kwiPCB.
3. Phuma iikliphu zokugcina zamacala amane kwaye utsale iPCB phezulu ukuze ucime izithuba zokugcina ikona.
4. Faka iPCB entsha.
5. Phinda uqhagamshele lonke uqhagamshelo lweplagi.
6. Hlanganisa kwakhona.
7. Vula amandla, umboniso ubonisa:

Cofa u-Ewe kwaye isikrini esilandelayo siyaboniswa:

Cofa Okulandelayo de kuboniswe [Logic Max]. Cofa Khetha.

Cinezela Okulandelayo de kuboniswe uhlobo oluchanekileyo lweBhola:
I-Combi, ubushushu, iNkqubo yase-UK okanye iNkqubo ye-IE Cofa Khetha ukuze uqinisekise kwaye isikrini esilandelayo siyaboniswa:

Cofa u-Khetha ukuze uqinisekise kwaye isikrini esilandelayo siyaboniswa:

Cofa Ewe ukugqiba

3.21 UTSHINTSHO NGESENSI YE-DHW FLOW turbine

1. Khupha inkqubo yeDHW.
   
2. Tsala uqhagamshelo lombane.
3. Ukusebenzisa isixhobo esifanelekileyo, phakamisa kwaye ususe ikliphu egcinayo.
4. Sebenzisa ikliphu ukwenza lula inzwa yeijini ukusuka kwindlu yayo.
5. Hlangana kwakhona ngenzwa entsha.

3.22 UKUTSHINTSHWA KWE-PRESURE GAUGE

1. Khupha ibhoyila.
2. Susa ibhoyili ngaphambili (jonga icandelo 3.4), yehlisa iphaneli yokulawula kwaye ususe isimbozo sebhokisi yokulawula.
3. Ukuqinisekisa ukuba akukho xinzelelo kwisixokelelwano sokucofa ikliphu ye-C kwizibuko lombhobho wokuhamba kwaye ususe uqhagamshelwano lwe-capillary kunye ne-'O' ring.
4. Ukukhulula iikliphu ezimbini ezigcinayo kwigeyiji yoxinzelelo lula igeyiji yoxinzelelo phambi kwephaneli yolawulo.
5. Faka igeyiji yoxinzelelo olutsha kumphambili wephaneli yolawulo esezantsi uqinisekisa ukuqhelaniswa okuchanekileyo. Khangela uqhagamshelo lokutyhala olungena kumbhobho ohambayo uqinisekise i-'O' iringi kwindawo kwaye ukhuseleke ngekliphu ka-'C'.
6. Gcwalisa kwakhona kwibhoyila.

3.23 UTSHINTSHO LWEPRV

1. Khupha ibhoyila.
2. Susa umgibe kunye nombhobho werabha.
3. Khupha kwaye ususe ikliphu egcina iPRV.
4. Phakamisa ngaphandle i-PRV/indibano yombhobho.
5. Susa umbhobho kwaye udlulisele kwi-PRV entsha.
6. Hlanganisa kwakhona uqinisekise ukuba ikliphu egciniweyo ifakwe ngokuchanekileyo.
7. Jonga ukusebenza kwe-PRV ngokuphakamisa uxinzelelo lwamanzi de i-valve iphakame. Oku kufuneka kwenzeke ngaphakathi kwe-0.3 bar yoxinzelelo lokunyuswa kwangaphambili.
8. Khangela ukuba akukho kubaleka kwamanzi okwenzekayo ngaphandle kwendawo yokukhupha
9. Ukukhulula amanzi kwinkqubo kude kube yinkqubo encinci yoxinzelelo loyilo; 1.0 bar ukuba isistim iza kucinezelwa kwangaphambili.

https://idealheating.com/logic-V4-literature-3

3.24 PUMP UTSHINTSHO OLUZENZAKALELAYO LWEMVENTO YOMOYA 

1. Khupha ibhoyila.
2. Susa isitya sokwandisa.
3. Okokuqala, yandisa indawo yokungena ngokuqhawula uqhagamshelo lombhobho oyi-22 mm ngaphezulu kwempompo eninzi kunye nomzantsi wesitshintshi sobushushu kwaye ususe umbhobho.
4. Intloko ye-automatic air vent igcinwe kumzimba wempompo kunye noxhumo lwe-bayonet. Intloko yevent yomoya kunye nendibano yefloat iyasuswa ngokujikisa intloko ngokuchasene newotshi.viewed ukusuka phezulu) kunye nokutsalela phezulu.
5. Hlanganisa kwakhona. Qinisekisa ukuba intloko ye-ivent yomoya ifakelwe i-'O' ring seal.
6. Qinisekisa ukuba isivalo somoya sikhululekile.
7. Gcwalisa kwakhona kwibhoyila. Qwalasela ukuvuza kwindawo entsha yokungena umoya.

Icandelo lesi-3 – Unikezelo lwenkonzo
3.25 UTSHINTSHO LWE-DHW THERMISTOR

1. Yahlula inkqubo yeDHW.
2. Susa ikliphu yokugcina kwaye ukhuphe i-thermistorYilungiselele ukukhutshwa kwamanzi.
3. Nciphisa intambo yokubopha.
4. Faka i-thermistor yokutshintsha kwaye udibanise kwakhona.
5. Phinda umisele ubonelelo lweDHW, vula impompo yamanzi ashushu ejonga ukuvuza.

3.26 I-DHW PLATE HEAT EXCHANGER REPLACEMENT

1. Khupha ibhoyila.
2. Susa umgibe we-condensate.
3. Susa izikrufu ezi-2 ze-hex ezikhusela isitshintshi sobushushu sepleyiti kwizindlu ezihlanganisiweyo.
4. Lawula ipleyiti yokutshintsha ubushushu ngaphandle kwe-LH ephezulu okanye iziko lendawo yolawulo. Qaphela nakuphi na ukuchitheka kwamanzi.
5. Faka ipleyiti entsha yokutshintsha ubushushu, usebenzisa i'O'-rings entsha enikezelweyo.
   Qinisekisa ukuba iidepressions zisezantsi phambi kokufakwa.
6. Hlanganisa kwakhona.
7. Gcwalisa kwakhona kwibhoyila.
8. Khangela ukuba ibhoyila isebenza kuzo zombini iindlela ze-DHW & CH.

3.27

UKUSEBENZA

Ukususa idibaniso yomzimba wevalvu:

1. Khupha ibhoyila.
2.  Susa umgibe we-condensate.
3. Susa iplagi yombane kwivalve yokuphambukisa.
4. Beka isikrudrayiva esisicaba esisicaba kwindawo yevalve ye-diverter motor body slot ebonelelweyo kwaye ukhulule imotor.
5. Susa i-return thermistor uxhumano lombane.
6. Susa uqhagamshelo lombane lwempompo.
7. Susa uqhagamshelo lombane lwe-DhW Turbine.
8. Susa i-DHW ipleyiti yokutshintsha ubushushu (inqaku loqhelaniso).
9. Khulula i-nut ngaphezulu kwempompo kwaye ujikelezise umbhobho.
10. Ukuba kuyafuneka susa umbhobho wodibaniso lomkhumbi wokwandisa.
11.  Susa isiziba se-DHW kunye noqhagamshelo lwe-CH lokubuyisela olubekwe phantsi kwebhoyila.
12. Susa izikrufu ezine zentloko ye-torx ulungisa i-manifold yokubuyisela kwisiseko sentsimbi yebhoyila.
13. Phakamisa udibaniso oluninzi kwaye ususe kwibhoyila.
14. Jija kwaye ususe ubuninzi be-DHW.
15. Susa izikrufu ezibini zokulungisa ivalve yomzimba kwaye urhoxise indibano yomzimba yevalve yesiphambukisi.
16. Faka idiverter body assembly entsha kwaye ubuyisele izikrufu ezibini zokulungisa.
17. Hlaziya ubuninzi be-DHW, udibanise indibano ubuyisele kwibhoyila kwaye uphinde udibanise.
18. Gcwalisa kwakhona kwibhoyila kwaye ujonge ukuvuza. Khangela ukuba ibhoyila isebenza kuzo zombini iindlela ze-DHW & CH.

3.28 UKUTSHINTSHWA KWENTLOKO

1. Khupha ibhoyila.
2. Nciphisa iintambo ezimbini zombane kwimpompo.
3. Susa izikrufu ezi-4 zeheksi ezigcina intloko yempompo.
4. Susa intloko yempompo. Kulumkele ukuchitheka kwamanzi.
5. Faka intloko yempompo entsha.
6. Hlanganisa kwakhona.
7. Gcwalisa kwakhona kwibhoyila.

3.29 CH UKUTSHINTSHA ITSHINTSHI YOXINZELELO LWAMANZI

1. Khupha ibhoyila.
2. Tsala imidibaniso emibini yombane.
3. Ukusebenzisa isixhobo esifanelekileyo, khupha ikliphu yokugcina isinyithi.
4. Ukurhoxisa ngononophelo iswitshi yoxinzelelo.
5. Faka iqhosha elitsha loxinzelelo kwaye udibanise kwakhona. Qinisekisa ukuba umsesane u-'O' ufakiwe kwaye ubuyisele ikliphu.
6. Gcwalisa kwakhona kwibhoyila.

Ibonisiweyo ijikelezisiwe 90º
3.31 UTSHINTSHO LWEJINJINI YE-HEAT

ISILUMKO: Khusela ulawulo lwegesi kunye nombane ngephepha elingangenwa ngamanzi.

1. Khupha ibhoyila (CH Circuit Drain).
   
2. Hlehlisa izikrufu ezibini kwaye ususe isigqubuthelo se-sump egcina i-flue manifold esezantsi.
3. Phakamisa i-manifold ukucima i-gasket yokutywina esezantsi kwaye ususe izinto ezininzi.
4. Susa indibano yefeni / yeVenturi kwaye uyibeke kwicala elinye.
5. Susa isitshisi kwaye ubeke kwicala elinye.
6. Susa i-electrode yokutshisa / yokubona.
   
7. Susa i-spark generator.
8. Susa ivalve yegesi.
9. Susa isitya sokwandisa.
10. Susa izikrufu ze-2 M5 ezigcina i-spark generator, isibiyeli sokuxhoma kunye nokudlulisa isibiyeli kwisitshintshi sobushushu esitsha.
11. Hlehlisa i-nut yempompo yomanyano, susa ikliphu kwaye ususe umbhobho kwisitya sokwandisa.
12. Susa iikliphu ezimbini zombhobho ogcinayo kwaye ususe imibhobho.
13. Susa umbhobho werabha we-condensate.
14. Susa izikrufu ezimbini zokulungisa umtshintshi wobushushu.
15. Susa umtshintshi wobushushu, slayida ngaphandle kwesibiyeli sendawo.
16. Ukuba i-sump yokubuyisela iyafuneka: Jikelezisa indibano yokutshintsha ubushushu nge-180º. Beka i-sump entsha kwisitshintshi sobushushu, uqinisekise ukuqhelaniswa okuchanekileyo kunye nesitywina sisendaweni.
    Emva koko sebenzisa ngokukhawuleza uxinzelelo kwisiseko se-sump kwindawo nganye yokulungisa ithebhu kwaye udibanise iithebhu kwi-heater exchanger.

3.32 UKWANDISA UMKHUBA WOKUTSHATSHWA KANYE & UKUTINTSHA UTSHINTSHO

UKUTSHAYISHA

1. Susa i-cap ye-charge point.
2. Hlaziya kwakhona uxinzelelo lwetanki kwi-0.75 bar.
3. Hlanganisa kwakhona.
   UTSHINTSHO
4. Khupha ibhoyili CH isiphaluka.
5. Susa ikliphu yokugcina kwisitya sombhobho wokudibanisa amanzi kwaye ususe umbhobho.
6. Ukuxhasa isitya sokwandisa kwaye ukhulule i-screws ezi-2 kwi-bracket yokukhusela, ebekwe phezulu kwibhoyili, kwaye ususe.
   Qaphela indawo yesibiyeli kwinqanawa.
7. Susa isitya sokwandisa.
8. Faka inqanawa entsha yokwandisa.
9. Hlanganisa kwakhona uqinisekise ukuba i-'O' ring seal ikhona kwaye ulungise ikliphu egciniweyo.
10. Gcwalisa kwakhona kwibhoyila kwaye ujonge ukuvuza.

ICandelo lesi-4 – Ukufumana iimpazamo

4.1 IMENU EYINGUNDOQO, UNCEDO NGEFAULT
Uncedo lokufumana iimpazamo lunokufikelelwa kwimenyu.
Uncedo lokufumana iimpazamo ludwelisa zonke iimpazamo eziqhelekileyo kunye neetshekhi eziyimfuneko. Iinkcukacha ezithe vetshe zokujonga iimpazamo kunye nezenzo zichazwe kumaphepha alandelayo.
4.2 UKUTSHINTSHWA NGOKUGQITHISILEYO

4.3 UKUKHISHWA KOMTHETHO

4.4 LUVUSE IINTLANGA PHAMBI KWEMVAVVU YEGAS

4.5 UXINZELELO LWAMANZI ANGAPHANTSI

4.6 UKULAHLEKELWA KWENTLANGA

4.7 INKONZO YABALANDELI

4.8 FLOW THERMISTOR FAULT

4.9 BUYISA I-THERMISTOR FAULT

4.10 IMPAHLA YOMVA PHANDLE

4.11 AKUKHO MSEBENZI WE-CH KODWA I-DHW ISEBENZA NGOKULUNGILEYO

4.12 AKUKHO DHW KODWA CH ISEBENZA KALUNGILE

4.13 AKUKHO MBONISO

4.14 DHW THERMISTOR FAULT

Icandelo le-5 - iiNdawo eziNgena ndawo

Xa ufaka endaweni yayo nayiphi na indawo kwesi sixhobo sebenzisa kuphela iindawo ezisecaleni onokuthi uqinisekiswe ukuba ziyahambelana neenkcukacha zokhuseleko kunye nokusebenza esikufunayo. Musa ukusebenzisa iinxalenye ezihlaziyiweyo okanye zokukhuphela ezingagunyaziswanga ngokucacileyo nguKufudumeza okuKufanelekileyo.
Ukungaphumeleli ukwenjenjalo kunokuchaphazela ukhuseleko okanye ukusebenza kwesi sixhobo.
Ulwazi oluphangaleleyo lwezahlulo kunye neenkcukacha zaMacandelo aLungileyo aVunyiweyo ayafumaneka kwi-idealparts.com
Iqela lethu lamaCandelo likwakhona ukuze likuncede ngemibuzo yakho yeeNdawo eziPhambili ku-01482 498665.
Xa ufowuna, kunye nokuqinisekisa ukuba sinokukubonelela ngezona nkcukacha zichanekileyo, nceda uqinisekise ukuba unokulandelayo;

• Imodeli yeBhola
• Inombolo ye-GC yesiXhobo
• Inombolo yeSeriya yeBoiler

ICandelo lesi-6 – Umlinganiselo wokuFundisa

Ikhowudi yokuSebenza
Ufakelo, ukugunyaziswa kunye nenkonzo yokufudumeza kwasekhaya kunye neemveliso zamanzi ashushu
IBenchmark ibeka uxanduva kubo bobabini abavelisi kunye nabafakeli.* Injongo kukuqinisekisa ukuba abathengi** babonelelwa ngesixhobo esichanekileyo ngokweemfuno zabo, ukuba sifakelwe, sigunyaziswe kwaye sinikezelwe ngenkonzo ngokuhambelana nemiyalelo yomenzi ngabantu abanobuchule kwaye siyahlangabezana. iimfuno zeMigaqo yeZakhiwo efanelekileyo. Abafaki kufuneka benze umsebenzi ngokuhambelana noku kulandelayo:
Ukusetyenziswa kwegama elithi Isifakeli akupheleliselwanga kufakelo ngokwalo kwaye luquka abo benza ufakelo, ukugunyazisa kunye/okanye ukusevisa ubushushu kunye neemveliso zamanzi ashushu, okanye ukusetyenziswa kweemveliso ezixhasayo (ezifana nokucocwa kwamanzi okanye izixhobo zovavanyo).
“Umthengi ubandakanya abaninimzi, abaqeshisi kunye nabaqeshi.
Imigangatho yoMsebenzi

• Yiba nobuchule kwaye ulungele ukwenza umsebenzi ofunekayo.
• Faka, ikhomishini, inkonzo kunye nokusebenzisa iimveliso ngokuhambelana nemiyalelo yomenzi enikiweyo.
• Qinisekisa ukuba apho kukho uxanduva lomsebenzi woyilo, ukufakela ubungakanani obuchanekileyo kwaye bufanele injongo.
• Ukuhlangabezana neemfuno zeMigaqo yeZakhiwo efanelekileyo. Apho oku kubandakanya umsebenzi owaziswayo yiba lilungu leSkimu soMntu oQoqekileyo okanye uqinisekise ukuba umthengi usazisile iLocal Authority Building Control (LABC), phambi kokuba uqalise umsebenzi.
• Gqibezela onke amacandelo afanelekileyo oLuhlu lweNqaku lokuHlola/iRekhodi yeNkonzo xa ugunyazisa okanye unikezela ngeenkonzo kwimveliso okanye inkqubo.
• Qinisekisa ukuba imveliso okanye inkqubo ishiywe ikwimeko ekhuselekileyo kwaye, nanini na kunokwenzeka, ikwimeko entle yokusebenza.
• Gxininisa kumthengi nawuphi na umsebenzi wokulungisa okanye wophuculo ochongiweyo ngexesha lokugunyaziswa okanye umsebenzi wokubonelela.
• Jonga kumnxeba woncedo womenzi apho uncedo lufuneka khona.
• Xela iimpazamo zemveliso kunye neenkxalabo kumenzi ngexesha elifanelekileyo.

Inkonzo eyenzelwe

• Bonisa umthengi naliphi na ikhadi lesazisi elinxulumene nomsebenzi owenziweyo phambi kokuqala okanye xa uceliwe.
• Nika inkcazo epheleleyo necacileyo/umboniso wemveliso okanye inkqubo kunye nokusebenza kwayo kumthengi.
• Hambisa imiyalelo yomenzi, kubandakanywa noLuhlu lokuQwalasela, kumthengi xa kugqityezelwa ukufakela.
• Fumana utyikityo lomthengi, kuLuhlu lokuQwalasela, ukuqinisekisa umboniso owanelisayo kunye nokufunyanwa kwemiyalelo yomenzi.
• Cebisa umxhasi ukuba unikezelo lwemveliso rhoqo luyafuneka, ngokuhambelana nezindululo zabavelisi, ukuqinisekisa ukuba ukhuseleko nokusebenza kakuhle kuyagcinwa.
• Phendula ngokukhawuleza kwiifowuni ezivela kumthengi emva kokugqitywa komsebenzi, ukunika iingcebiso kunye noncedo ngefowuni kwaye, ukuba kuyimfuneko, ukutyelela umthengi.
• Lungisa naziphi na iingxaki zokufakela ngaphandle kweendleko kumthengi ngexesha lesiqinisekiso somfaki.

Ukugunyaziswa komgangatho kunye neRekhodi yeNkonzo yoQinisekiso lweWaranti
Kuyimfuneko ukuba ibhoyila ifakwe kwaye ithunyelwe kwimiyalelo yabavelisi kunye nemimandla yedatha kuluhlu lokutshekisha lokugunyazisa lugqitywe ngokupheleleyo.
Ukuqalisa iwaranti yebhoyila ibhoyila kufuneka ibhaliswe kumenzi kwinyanga enye yofakelo. Iwaranti ixhomekeke kumsebenzisi wokugqibela (umthengi), kwaye kufuneka baziswe ukuba ekugqibeleni luxanduva lwabo ukubhalisa kunye nomenzi, kwixesha elinikiweyo.
Kubalulekile ukuba ibhoyila inikwe inkonzo ngokuhambelana neengcebiso zabavelisi, ubuncinane ngonyaka. Oku kufuneka kuqhutywe yiNjineli ebhalisiweyo yeGas Safe ebhalisiweyo. Iinkcukacha zenkonzo zifanele zirekhodwe kwiNkozo yoQhakamshelwano kunye neRekhodi Yomsebenzi Webhola yeThutyana ize ishiywe kumninimzi. Ukungaphumeleli ukuthobela imiyalelo yabenzi benkonzo kunye neemfuno kuya kwenza ukuba iwaranti ingasebenzi.

www.hhic.co.uk

Olu Luhlu lokuQinisekisayo kufuneka lugqitywe ngokupheleleyo ngumntu onobuchule othe wagunyazisa isitshisi sebhoyila njengendlela yokubonisa ukuthotyelwa kweMigaqo yeZakhiwo efanelekileyo aze emva koko anikezelwe kumthengi ukuba ayigcinele ireferensi yexesha elizayo.
Ukungaphumeleli ukuhlohla kunye nokugunyaziswa ngokwemiyalelo yabenzi kunye nokuzalisa olu Luhlu lokuQinisekisa lweBenchmark luya kwenza iwaranti ingasebenzi. Oku akuchaphazeli amalungelo asemthethweni omthengi.
* Lonke ufakelo eNgilani naseWales kufuneka waziswe kwiLocal Authority Building Control (LABC) ngokuthe ngqo okanye ngeSkimu soMntu oMntu. ISatifikethi sokuThotyelwa kweMigaqo yeZakhiwo siya kunikezelwa kumthengi.
© IBhunga loShishino lokufudumeza kunye neHopwater (HHIC)

www.centralheating.co.uk

ULUHLU LWENKQUBO YEGAS YEBILETHA NEREKHODI YOKUQINISEKISA

Idilesi:

Ukwenziwa kwebhoyila kunye nemodeli:

Inombolo yesiriyeli yebhoyila:

Igunyaziswe ngu (PRINT NAME):

Inombolo yobhaliso eKhuselekileyo ngegesi:

Igama leKhampani:

Inombolo yefowni:

I-imeyile yenkampani:

Idilesi yenkampani:

Umhla wokumiselwa:

Inkqubo yokufudumeza kunye namanzi ashushu ithobela iMigaqo yeZakhiwo efanelekileyo? Ewe

Ukuzikhethela: Inombolo yeSaziso seMigaqo yeZakhiwo (ukuba ikhona):

Ixesha, ulawulo lobushushu kunye nebhoyila idityanisiwe ibonelelwe ukufudumeza okuphakathi kunye namanzi ashushu

Ewe

Iimfuno zeBoiler Plus (phawula kwi(ii)bhokisi ezifanelekileyo

I-Boiler Plus ukhetho olukhethiweyo kwibhoyila edibeneyo e-ENGLAND

Imbuyekezo yemozulu

I-Smart thermostat ene-atomization kunye nokwenza ngcono

Layisha imbuyekezo

Flue Gas UkuBuyiswa kobushushu

Ixesha kunye nolawulo lobushushu kumanzi ashushu

I-Cylinder thermostat kunye nomdwelisi/ixesha

Ibhoyili edibeneyo

Iivalvu zendawo

esele ikhona

Ifakelwe

Ayifuneki

Iivalvu zeradiyetha ze-Thermostatic

esele ikhona

Ifakelwe

Ayifuneki

Ukugqitha okuzenzekelayo kwisixokelelwano

esele ikhona

Ifakelwe

Ayifuneki

Ukufudumeza ngaphantsi kobushushu

esele ikhona

Ifakelwe

Ayifuneki

INKONZO & IREKHODI YOMSEBENZI YETHUTYANA
Kucetyiswa ukuba ibhoyila yakho kunye nenkqubo yokufudumeza igcinwe rhoqo kwaye igcinwe, ngokuhambelana nemiyalelo yabavelisi, kwaye inkonzo efanelekileyo /
irekhodi yomsebenzi wethutyana igqityiwe.
Mnikezi nkonzo
Xa ugqibezela ingxelo yenkonzo (njengalapha ngezantsi), nceda uqinisekise ukuba uyenzile inkonzo njengoko ichazwe kwimiyalelo yabavelisi. Ngalo lonke ixesha sebenzisa iindawo ezisecaleni ezichaziweyo zabenzi. ICandelo lesi-6 – Umlinganiselo wokuFundisa

INKONZO/UMSEBENZI WETHUTYANA KWIBOILER cima ngokufanelekileyo					Umhla:
Igama leNjineli:			Igama leKhampani:
Umnxeba N °:			Ubhaliso oluKhuselekileyo lwegesi N °:
Umlinganiselo omkhulu	CO ppm		CO2 %	CO/CO2
Ixabiso eliphantsi	CO ppm		CO2 %	CO/CO2
Apho kunokwenzeka, ngaba kuye kwahlolwa ingqibelelo ngokutyibilikayo ngokungqinelana nemiyalelo yabavelisi, kwaye ufundo luchanekile?”				Ewe
Umlinganiselo werhasi:		m3/h	OR	fts/h
Ngaba amalungu afakelwe? cima ukucima ngokufanelekileyo			Ewe	Hayi
Amalungu afakelwe:
I-system inhibitor concentration ihlolwe kwaye inyathelo elifanelekileyo lithathwe, ngokuhambelana ne-BS 7593 kunye nemiyalelo yabavelisi bebhoyili. *				Ewe		n / A
Izimvo: Utyikityo:

*Uvavanyo lwe-System inhibitor efficacy test luyafuneka kwinkonzo nganye yonyaka ngokuhambelana nemiyalelo yabavelisi kunye ne-BS 7593. Kwamkelekile kuphela ukuba ungalwenzanga oku ukuba utyelelo lweenjineli zenkonzo lwaluphakathi kweenkonzo zonyaka ukuya kwindawo engeyoyamanzi. icandelo.
*Uvavanyo lwe-System inhibitor efficacy test luyafuneka kwinkonzo nganye yonyaka ngokuhambelana nemiyalelo yabavelisi kunye ne-BS 7593. Kwamkelekile kuphela ukuba ungalwenzanga oku ukuba utyelelo lweenjineli zenkonzo lwaluphakathi kweenkonzo zonyaka ukuya kwindawo engeyoyamanzi. icandelo.
*Uvavanyo lwe-System inhibitor efficacy test luyafuneka kwinkonzo nganye yonyaka ngokuhambelana nemiyalelo yabavelisi kunye ne-BS 7593. Kwamkelekile kuphela ukuba ungalwenzanga oku ukuba utyelelo lweenjineli zenkonzo lwaluphakathi kweenkonzo zonyaka ukuya kwindawo engeyoyamanzi. icandelo.
* Lonke ufakelo eNgilani naseWales kufuneka waziswe kwiLocal Authority Building Control (LABC) ngokuthe ngqo okanye ngeSkimu soMntu oMntu. ISatifikethi sokuThotyelwa kweMigaqo yeZakhiwo siya kunikezelwa kumthengi. © IBhunga loShishino loKufudumeza kunye naManzi ashushu (HHIC)

I-FLOWCHART YENQANABA LE-CO KUNYE NE-COMBUUSTION RATIIO CHECK EKUBENISELWE I-BOILER EPHOXISAYO
ICandelo lesi-6 – Umlinganiselo wokuFundisa
Ulwazi lokuqala oluBalulekileyo kwiitshekhi
Ivalve yomlinganiselo werhasi yomoya isetiwe kwifektri kwaye kufuneka ingalungiswa NGEXESHA LOKUTHUMELA.
Ukuba ibhoyila ifuna uguqulo ukuze isebenze nosapho olwahlukileyo lwerhasi (umzekelo, uguqulo ukusuka kwirhasi yendalo ukuya kwiLPG)
Isikhokelo esahlukileyo sinikiwe nekhithi yokuguqula inikwe kwaye oku makulandelwe.
NGAPHAMBI KWENQANABA LE-CO KUNYE NE-COMBUSTION RATIO CHECK
Imiyalelo yokufakela kufuneka ilandelwe, uhlobo lwegesi luqinisekisiwe kwaye uxinzelelo lokubonelela ngegesi / izinga legesi litshekishwe njengoko lifuneka phambi kokuba kugunyaziswe.
Njengenxalenye yenkqubo yokufakela, INGAKUMBI APHO UFLUE UFANELELWE NGABANTU ABANGAPHANDLE.
I-BOILER INSTALLER, jonga ngokubonakalayo ingqibelelo yenkqubo ye-flue yonke ukuqinisekisa ukuba onke amacandelo ahlanganiswe ngokuchanekileyo, agxininiswe kwaye axhaswa. Khangela ukuba ubude bombhobho abugqithiswanga kwaye zonke izikhokelo zilandelwe (umz. iGas Safe Register Bulletin Technical (TB) 008 apho itshimini/imibhobho ivaliwe).
I-ECGA kufuneka ibe yohlobo oluchanekileyo, njengoko kuchazwe yi-BS EN 50379-3: 2012.
Ngaphambi kokusetyenziswa kwayo, i-ECGA kufuneka igcinwe kwaye ilinganiswe njengoko kuchaziwe ngumvelisi. Umfakeli kufuneka abe nobuchule obufanelekileyo bokusetyenziswa komhlalutyi. Khangela kwaye zero i-analyzer KUMOYA OMHLAZIYO ngokuhambelana nemiyalelo yomenzi we-analyzer.
ISIQEPHU:
CO = carbon monoxide
CO2 = carbon dioxide
O2 = ioksijini
I-Combustion Ratio = Ukufundwa kwe-CO kulinganiswe kwi-ppm eyahlulwe ngokufunda kwe-CO2 kuqala iguqulelwe kwi-ppm ppm = iinxalenye ngesigidi
I-GS (I&U) R = Ukhuseleko lweGesi (uFakelo kunye nokuSetyenziswa) Imigaqo

ICandelo lesi-6 – Umlinganiselo wokuFundisa

 

Kwi-Ideal Heating sithatha impembelelo yethu yokusingqongileyo ngokubalulekileyo, ngoko ke xa ufaka nayiphi na imveliso yokuFundisa ngokufanelekileyo nceda uqiniseke ukuba ulahla nayiphi na
isixhobo sangaphambili ngendlela ekhathalela indalo esingqongileyo. Amakhaya angaqhagamshelana nabasemagunyeni basekuhlaleni ukuze bafumanise ukuba njani.
'Yabona https://www.gov.uk/managing-your-waste-an-overview ukufumana isikhokelo malunga nendlela yokubuyisela ngokufanelekileyo inkunkuma yeshishini lakho.
UQeqesho lobuGcisa
I-Academy yethu yeeNgcali inikezela ngoluhlu lweenketho zoqeqesho ezilungiselelwe kwaye zihanjiswe ziingcali zethu zokufudumeza.
Ngeenkcukacha nceda uqhagamshelane: ingcali-academy.co.uk
I-Ideal Boilers Ltd., ilandela umgaqo-nkqubo wokuqhubeka nokuphucula kuyilo kunye nokusebenza kweemveliso zayo.
Ilungelo ke ngoko ligcinelwe ukwahluka kwenkcazo ngaphandle kwesaziso.
Xa utshintshela kuyo nayiphi na indawo kwesi sixhobo, sebenzisa kuphela iindawo ezisecaleni onokuthi uqinisekiswe ukuba ziyahambelana neenkcukacha zokhuseleko kunye nokusebenza esikufunayo. Musa ukusebenzisa iinxalenye ezihlaziyiweyo okanye zokukhuphela ezingagunyaziswanga ngokucacileyo nguKufudumeza okuKufanelekileyo. Ukufumana ikopi yamva nje yoncwadi lwengcaciso kunye nezenzo zokulondolozwa ndwendwela yethu webindawo idealheating.com apho unokukhuphela ulwazi olufanelekileyo kwifomathi yePDF. NgoJulayi 2022
I-UIN 228290 A05

WEEE Directive 2012/19/EU
Inkunkuma yoMyalelo weSixhobo soMbane kunye ne-Electronic

• Ekupheleni kobomi bemveliso, lahla ukupakishwa kunye nemveliso kwiziko elihambelanayo lokurisayikilishwa.
• Musa ukulahla iyunithi kunye nenkunkuma eqhelekileyo yasekhaya.
• Musa ukutshisa imveliso.
• Susa iibhetri.
• Lahla iibhetri ngokweemfuno zomthetho zengingqi hayi ngenkunkuma eqhelekileyo yasekhaya.

Bonke abafakeli beRejista yoKhuseleko lweGesi baphatha ikhadi lesazisi seGesi eKhuselekileyo, kwaye banenombolo yobhaliso. Zombini kufuneka zirekhodwe kuLuhlu lokuQinisekisa iBenchmark. Ungajonga isifakeli sakho ngokufowunela iRejista eKhuselekileyo yeGesi ngqo ku-0800 4085500.
Ukufudumeza okuFanelekileyo lilungu leBenchmark scheme kwaye lixhasa ngokupheleleyo iinjongo zenkqubo. I-Benchmark iye yaziswa ukuphucula imigangatho yokufakela kunye nokugunyaziswa kweenkqubo zokufudumeza okuphakathi e-UK kunye nokukhuthaza ukusetyenzwa rhoqo kwazo zonke iinkqubo zokufudumeza okuphakathi ukuqinisekisa ukhuseleko kunye nokusebenza kakuhle.
IREKHODI YENKONZO YENKONZO YENKONZO MAYIGQITSHWE EMVA KWENKONZO NGANYE.

1.1. INTSHAYELELO
I-Logic MAX Combi 2 yibhoyila edibeneyo ebonelela ngokufudumeza okuphakathi kunye namanzi ashushu asekhaya kwangoko. Ibonisa ulandelelwano olupheleleyo lokuvutha okuzenzekelayo kunye nokutsha okuncediswa yifeni.
Ngenxa yokusebenza okuphezulu kwebhoyila, i-condensate iveliswa kwiigesi ze-flue kwaye oku kuchithwa kwindawo efanelekileyo yokulahla ngombhobho wenkunkuma yeplastiki kwisiseko sebhoyila. I-condensate 'plume' iya kubonakala kwakhona kwi-terminal flue.
Ukhuseleko lwangoku loKhuseleko lwerhasi (uFakelo nokuSetyenziswa) Imigaqo okanye imithetho esebenzayo.
Kungumthetho ukuba olu fakelo lwesixhobo kunye nawuphi na umsebenzi owenziwe kwisixhobo uqhutywa yiNjineli eBhalisiweyo yeGesi eKhuselekileyo ngokuhambelana nale Mithetho ingentla.
Kubalulekile ukuba imiyalelo ekule ncwadana ilandelwe ngokungqongqo, ukwenzela ukusebenza ngokukhuselekileyo nangoqoqosho kwibhoyila.
Ukubonelelwa kombane
Esi sixhobo kufuneka sifakwe emhlabeni.
Ubonelelo: 230 V ~ 50 Hz. Ukudibanisa kufuneka kube ngu-3 A. Amanqaku abalulekileyo

• Esi sixhobo akufuneki sisetyenziswe ngaphandle kwebhokisi efakwe ngokufanelekileyo kwaye yenze itywina elaneleyo.
• Ukuba ibhoyila ifakwe kwikhompatimenti ngoko ke ikhompatimenti MAYINGASETYENZISWA ngenjongo yokugcina.
• Ukuba kuyaziwa okanye kurhanelwa ukuba kukho impazamo kwibhoyila AKUFUNEKA ISETYENZISWE de isiphene silungiswe yiNjineli eBhalisiweyo yeGesi eKhuselekileyo.
• AKUKHO naphantsi kwazo naziphi na iimeko ukuba nawaphi na amacandelo atywiniweyo akwesi sixhobo asetyenziswe ngokungachanekanga okanye tampenziwe nge.
• Esi sixhobo sinokusetyenziswa ngabantwana abaneminyaka eyi-8 nangaphezulu. Kwakhona abantu abanokuthotywa kwekhono lomzimba, loluvo okanye ngokwasengqondweni, okanye abaswele amava nolwazi, ukuba baye banikwa iliso okanye umyalelo omalunga nokusetyenziswa kwesixhobo sombane ngendlela ekhuselekileyo kwaye baziqonde iingozi ezibandakanyekileyo. Abantwana abasayi kudlala ngesixhobo sombane. Ukucoca kunye nokugcinwa komsebenzisi akuyi kwenziwa ngabantwana ngaphandle kweliso.

1.2 UKUSEBENZA KWEBILI

Intsomi
A. Amanzi Ashushu Asekhaya
Iqhosha lobushushu
B. IKnobhu yoBubushushu obuphakathi
C. Izitshixo ezishushu
D. Ukuboniswa koBume beBoiler
E. Burner On Indicator
F. Iqhosha leMowudi
UKUQALA IBOiler
Qalisa ibhoyila ngolu hlobo lulandelayo:

1. Qinisekisa ukuba zonke iimpompo zamanzi ashushu zivaliwe.
2. Vula umbane kwibhoyila kwaye ujonge ukuba zonke izilawuli zangaphandle, umz. umdwelisi weprogram kunye ne-thermostat yegumbi, zivuliwe.
3. Cofa iqhosha leMowudi de uLungele okanye uVule uboniswe ngaphantsi kweTap kunye neesimboli zeRadiator.
4. Jika iqhosha lobushushu lamanzi asekhaya (A) ngokwewotshi kude kube yi-65°C ekujoliswe kuyo kubonisiwe. Jika iKnob yeqondo lobushushu eliphakathi (B) ngasekunene kude kube yi-80°C ekujoliswe kuyo kubonisiwe.
   Ibhoyila iya kuqalisa ulandelelwano lokutshisa, ukunika ubushushu kwisifudumezi esiphakathi, ukuba kuyafuneka.

Phawula. Kumsebenzi wesiqhelo isiboniso sesimo sebhoyila (D) siya kubonisa imiyalezo.
Jonga kwiCandelo
1.8
Ukhuseleko lwebhoyila kwiqabaka – ibhoyila iya kutsha ukuba ubushushu bungaphantsi kwe-5ºC.
Ngexesha lokusebenza okuqhelekileyo isitshisi kwisimboli (E) siya kuhlala sikhanyisiwe xa isitshisi silayitiwe.
Ukuba ibhoyila iyasilela ekukhanyeni emva kwemizamo emihlanu le miyalezo engalunganga iya kuboniswa:

Ukuqalisa kwakhona ibhoyila, cofa u-'Restart'. Ibhoyila iya kuphinda ulandelelwano lokutshisa. Ukuba ibhoyila isasilela ukukhanyisa jongana noMfaki weGesi oBhalisiweyo.
IIINDLELA ZOKUSEBENZA
Iimeko zaseBusika – (Ukufudumeza okusembindini kunye naManzi ashushu asekhaya ayafuneka)
Cinezela iQhosha leNdlela de ibe iLungile okanye iLayishiwe iboniswe phantsi kweesimboli zeTephu kunye neRadiator [ ].
Ibhoyila iya kubasa kwaye inike ubushushu kwiiradiyetha.
Ubushushu basekhaya bamanzi ashushu busebenza ngeqhosha le-preheat elisetelwe ku-'Preheat On'.
Iimeko zasehlotyeni – (Amanzi Ashushu AseKhaya afuneka kuphela) Cofa iqhosha leModi de uLungile okanye Vula uboniswe phantsi kophawu lweTephu [ ] kwaye Valiwe iboniswe phantsi kwesimboli yeRadiator [ ]. OKANYE Beka imfuno yokufudumeza esembindini kulawulo lwangaphandle UKUVALA.
Ubushushu basekhaya bamanzi ashushu busebenza ngeqhosha le-preheat elisetelwe 'Amanzi ashushu Avuliwe'. Ibhoyila icimile
Cwangcisa iqhosha lemowudi (C) ukuya 'BOILER OFF'. Umbane ongundoqo webhoyila kufuneka ushiywe ukuze ukhuseleke kwiqabaka (jonga uKhuseleko lweFrost).
I-PREHEAT – AMANZI ENTSHOZIYO ASEKHAYA
Umtshintshi wokushisa wamanzi ashushu wasekhaya ngaphakathi kwibhoyili unokugcinwa ushushu ngaphambili ukubonelela ngokukhawuleza ukuhanjiswa kwamanzi ashushu kwimpompo. Oku kuphunyezwa ngokucinezela iqhosha lokutshisa kwangaphambili ukuze 'Preheat On' okanye 'Preheat Timeed'.
Ibhoyili iya kusebenza ngamaxesha athile kwimizuzwana embalwa ukugcina umtshintshi wokushisa wamanzi ashushu asekhaya kwindawo eshushu ngaphambili. Ixesha eliphakathi kokusebenza yimizuzu engama-90. Oku kunokwahluka kakhulu ngenxa yobushushu oburhangqileyo bebhoyila. Ibhoyila iya kusebenza nanini na kukho imfuneko yamanzi ashushu asekhaya. Ukuba unikezelo lwamanzi ashushu asemgangathweni luyonelisayo seta i-preheat ibe 'Preheat Off'.
Ukuba i-Preheat itshintshelwe kwi-Tieding ke ukufudumeza kwangaphambili kuyakwenzeka kuphela xa kuyimfuneko kunalo lonke ixesha. Ibhoyila ifunda indlela yokusetyenziswa kweDHW evekini kwaye emva koko amaxesha iDHW preheat ukuze isebenze kuphela ngamaxesha okusebenzisa ukusuka kwiveki ephelileyo.
Oku kuphucula isantya sokuphendula kwi-DHW ngelixa kunciphisa ukusetyenziswa kwegesi.
ULAWULO LOBUSHUSHU BAMANZI Amanzi Ashushu Asekhaya Ubushushu bamanzi ashushu asekhaya buqingqwa lulawulo lwebhoyila ukuya kubushushu obuphezulu obungama-65.
º C, elungelelanisiweyo ngokusebenzisa iqhosha lobushushu bamanzi ashushu asekhaya (A). Kwiqondo eliphantsi lokutsalwa kwe-DHW ubushushu obuphezulu bunokugqitha kuma-65ºC. Ubushushu obuqikelelweyo bamanzi ashushu asekhaya:

Ukusetwa kweKnobhu	Ubushushu baManzi ashushu (malunga.)
Ubuncinane	40ºC
Ubuninzi	65ºC

Ngenxa yokwahluka kwenkqubo kunye nokuguquguquka kwamaqondo onyaka, amazinga okuhamba kwamanzi ashushu asekhaya / ukunyuka kwamaqondo obushushu kuya kwahluka, kufuna uhlengahlengiso kwimpompo : okuya kusezantsi izinga lokuqukuqela liphezulu iqondo lobushushu, kwaye ngokuphambeneyo.
UBUSHUSHU BASESIPHAKATHINI
Ibhoyila ilawula ubushushu obuphakathi kweradiyetha ukuya kuthi ga kwi-80 ephezulu
C, elungelelanisiweyo ngokusebenzisa iqhoshana lobushushu eliphakathi (B). o Umlinganiselo wamaqondo obushushu obuphakathi:

Ukusetwa kweKnobhu	Ubushushu baManzi ashushu (malunga.)
Ubuncinane	30ºC
Ubuninzi	80ºC

Kuseto lwezoqoqosho [ ] bhekisa kuSebenzi lweNkqubo yokuFundisa eLungileyo.
UKUSEBENZA KWENKQUBO YOKUFUDUMISA OKUFANELEKILEYO
Ibhoyila yinto ephezulu, isixhobo sombane esiza kulungelelanisa imveliso yayo ukuze ihambelane nemfuno yobushushu. Ke ngoko ukusetyenziswa kwegesi kuncitshisiwe njengoko imfuno yobushushu iyancipha.
Ibhoyila idibanisa amanzi kwiigesi ze-flue xa isebenza ngokufanelekileyo. Ukusebenzisa ibhoyila yakho ngokufanelekileyo (usebenzisa irhasi encinci) jika iqhosha lokufudumeza esembindini (B) de kuboniswe isimboli segqabi [ ]. Ngamaxesha obusika kunokuba yimfuneko ukujika iqhoshana ngasekunene ukuya kumaqondo obushushu aphezulu umz. 80, ukuhlangabezana neemfuno zakho zokufudumeza. Oku kuya kuxhomekeka kwindlu kunye neeradiyetha ezisetyenzisiweyo.
Ukunciphisa ukusetwa kwe-thermostat yegumbi nge-1ºC kunokunciphisa ukusetyenziswa kwegesi ukuya kuthi ga kwi-10%.
IMBUYEKEZO YEMOYA
Xa ukhetho lweMbuyekezo yeMozulu lufakelwe kwisixokelelwano ngoko iqhoshana lobushushu eliphakathi (B) libe yindlela yokulawula ubushushu begumbi. Jika iqhosha ngasekunene ukonyusa ubushushu begumbi kunye nokuchasene newotshi ukunciphisa ubushushu begumbi. Nje ukuba useto olufunekayo luphunyeziwe, shiya iqhoshana kule ndawo kwaye inkqubo iya kufezekisa ngokuzenzekelayo ubushushu begumbi obufunwayo kuzo zonke iimeko zemozulu zangaphandle.
UKHUSELEKO lwe-BOILER FROST
Ibhoyila ifakwe ukhuseleko lweqabaka olusebenza kuzo zonke iindlela, ngaphandle kokuba unikezelo lwamandla kwibhoyila luhlala luvuliwe. Ukuba amanzi kwibhoyila awela ngaphantsi kwe-5ºC, ukhuselo lweqabaka luya kusebenza kwaye luqhube kwibhoyila ukunqanda umkhenkce. Inkqubo ayiqinisekisi ukuba zonke ezinye iindawo zenkqubo ziya kukhuselwa.
Ukuba inkqubo ye-thermostat yeqabaka ifakiwe, ibhoyila kufuneka imiselwe kwimo yasebusika, [ ], ukuze inkqubo yokhuseleko lweqabaka isebenze.
Ukuba akukho nkqubo yokhuselo lweqabaka enikezelwayo kunye neqabaka kusenokwenzeka ngexesha lokungabikho elifutshane ekhaya kuyacetyiswa ukuba ushiye inkqubo yokulawula ukufudumeza okanye eyakhelwe umdwelisi nkqubo (ukuba ifakelwe) ilayitiwe kwaye isebenza kwisethingi yobushushu obuncitshisiweyo. Ixesha elide, yonke inkqubo kufuneka ikhutshwe.
UKUQALA KWAKHONA KWE-BOILER
Ukuqalisa kwakhona ibhoyila, xa uqondiswe kwimiyalezo ephosakeleyo edwelisiweyo cofa iqhosha elithi "Qalisa kwakhona". Ibhoyili iya kuphinda ukulandelelana kwayo kokutshisa. Ukuba ibhoyila isasilela ukuqalisa dibana neNjineli eBhalisiweyo yeGesi eKhuselekileyo.
AMANQAKU AMANQAKU AMANQAKU
Ukususa onke amandla kwibhoyila umbane ongundoqo kufuneka ucinywe.

1.3 UXINZELELO LWAMANZI KWINKQUBO
Igeyiji yoxinzelelo lwenkqubo enokuthi ibe viewed ngokuthoba ucango lokuhla, lubonisa uxinzelelo lwenkqubo yokufudumeza esembindini. Ukuba uxinzelelo lubonakala luwela ngaphantsi koxinzelelo lwangaphambili lofakelo lwe-1-2 bar ngexesha lexesha kwaye luqhubeke nokuwa ngoko ukuvuza kwamanzi kunokubonakaliswa. Kwesi siganeko phinda ucinezele inkqubo njengoko kubonisiwe ngezantsi. Ukuba awukwazi ukwenza njalo okanye ukuba uxinzelelo luyaqhubeka ukuhla i-Gas Safe Registered Engineer kufuneka kuqhagamshelwane nayo.
I-BOILER AYIYI KUSEBENZA UKUBA UXINEZELEKO LWEHLILE ukuya ngaphantsi
0.3 IBHA NGAPHANTSI KWALO MIMEKO.

Ukunyusa inkqubo :1.

1. Qinisekisa ukuba zombini & iziphatho (ezibhlowu & eziluhlaza) zikwindawo evaliweyo (njengoko kubonisiwe ngezantsi)
2. Susa iplagi kunye nekepusi kwaye uyigcine.
3. Xhuma i-loop yokuzalisa kwi-inlet yaManzi ashushu asekhaya (DHW) kwaye uqinise. Kwakhona qinisekisa ukuba elinye icala lokuzalisa loop liqinile ngesandla.
4. Jika isiphatho saManzi ashushu asekhaya (DHW) Isibambo esiblowu siye kwindawo ethe tye.
5. Ukuqinisekisa ukuba akukho kuvuza kubonwayo, jika ngokuthe chu umqheba welophu yokuzalisa (eluhlaza) BB kwindawo ethe tye.
6. Lindela i-gauge yoxinzelelo ukufikelela kwi-1 ukuya kwi-1.5 bar.
7. Nje ukuba uxinzelelo lufikelele kwiivalvu zokujika kunye nokubuyela kwindawo evaliweyo. B
8. Nqamula i-loop yokuzalisa, buyisela i-cap kunye neplagi. Kunokubakho ukuchitheka kwamanzi kweli nqanaba.

Ukuzalisa izithuba ezibonisiweyo
Izikhundla eziphezulu eziphezulu zibonisiwe

1.4 IINGONGOMA ZOMSEBENZISI WESIBILI
Ngokuhambelana nomgaqo-nkqubo wethu wangoku wewaranti singakucela ukuba ujonge kwesi sikhokelo silandelayo ukuchonga naziphi na iingxaki ezingaphandle kwibhoyila phambi kokuba ucele utyelelo lweenjineli zenkonzo. Ukuba ingxaki ifunyaniswa ingekho kweso sixhobo sinelungelo lokubiza intlawulo yotyelelo, okanye kulo naluphi na utyelelo olucwangcisiweyo apho ukufikelela kungafunyanwanga yinjineli. NGAYO NAYIPHI NA IMIBUZO NCEDA UKHAWELE INCEDA YOKUNCEDA OKUSEMTHETHWENI : 01482 498660 INKQUBO YOKUQALISA IBHAYIBHILE – Ukuqalisa kwakhona ibhoyila cofa iqhosha lokuqalisa kwakhona
1.5 UMKHUSO OQINISEKILEYO OQINISEKILEYO
Esi sixhobo sifakwe i-siphonic condensate trap system enciphisa umngcipheko we-condensate yesixhobo ukusuka kwiqhwa. Nangona kunjalo kufuneka umbhobho we-condensate kule nto
ukukhenkcisa isixhobo, nceda ulandele le miyalelo: a. Ukuba awuziva ufanelekile ukwenza le miyalelo yokuphelisa iqabaka engezantsi nceda ufowunele iGas yengingqi yakho eKhuselekileyo
Umfaki obhalisiweyo woncedo.
b. Ukuba uziva ufanelekile ukwenza le miyalelo ilandelayo nceda wenze njalo ngononophelo xa uphethe izinto ezishushu. MUSA ukuzama ukunyibilikisa imibhobho ngaphezu komgangatho ophantsi.
Ukuba esi sixhobo siphuhlisa ukuvaleka kumbhobho waso wecondensate, i-condensate yaso iya kwakha ukuya kuthi ga kwindawo apho iya kwenza ingxolo ekhangazayo phambi kokutshixa ngaphandle ibonisa "Ignition Lockout" kumboniso. Ukuba isixhobo siqalwe ngokutsha siyakwenza ingxolo ekhangazayo phambi kokuba sitshixelwe ngaphandle sibonisa “Ignition Lockout” kumboniso.
Ukuvula umbhobho wecondensate enomkhenkce;

1. Landela indlela yombhobho weplastiki ukusuka kwindawo yawo yokuphuma kwisixhobo, ngokusebenzisa indlela yawo ukuya kwindawo yokuyeka.
   Khangela indawo evalekile engumkhenkce. Kungenzeka ukuba umbhobho ukhenkceke kweyona ndawo ivulelekileyo ngaphandle kwesakhiwo okanye apho kukho umqobo wokuhamba. Oku kunokuba njalo
   ekupheleni okuvulekileyo kombhobho, kwi-bend okanye kwi-elbow, okanye apho kukho ukudibanisa kumbhobho apho i-condensate inokuqokelela khona. Indawo yokuvala kufuneka ichongwe ngokusondeleyo kangangoko ngaphambi kokuba kuthathwe amanyathelo angakumbi.
2. Qaba ibhotile yamanzi ashushu, ipakethe yobushushu efakwe kwi-microwave okanye eshushu damp ilaphu kwindawo engumkhenkce evalekile. Izicelo ezininzi kusenokufuneka zenziwe phambi kokuba iqhaqhazelise ngokupheleleyo.
   Amanzi ashushu anokugalelwa kumbhobho osuka kwitoti yokunkcenkceshela okanye okufanayo. MUSA ukusebenzisa amanzi abilayo.
3. Lumka xa usebenzisa amanzi ashushu njengoko oku kunokuba ngumkhenkce kwaye kubangele ezinye iingozi zendawo.
4. Emva kokuba isithintelo sisusiwe kwaye i-condensate inokuhamba ngokukhululekileyo, qalisa ngokutsha isixhobo. (Jonga "Ukuqalisa ibhoyila")
5. Ukuba isixhobo sombane asikwazanga ukucimba, tsalela umnxeba kwiNjineli eBhalisiweyo yeGesi eKhuselekileyo.
   Izisombululo zothintelo
   Ngexesha lemozulu ebandayo, seta iqhoshana lobushushu eliphakathi (B) ukuya ku-“MAX”, (Khumbula ukuba ubuyele kwisetingi yasekuqaleni nje ukubanda kuphelile).
   Beka isifudumezi rhoqo kwaye ujike ithermostat yegumbi iye kutsho kwi-15ºC ngobusuku okanye xa kungekho mntu. (Buyela kwimeko yesiqhelo emva kokubanda).

1.6 IINKCUKACHA NGOKUBANZI
I-BOILER PUMP
Impompo yebhoyila iya kusebenza ngokufutshane njengendawo yokuzijonga kanye rhoqo kwiiyure ezingama-24, kungakhathaliseki imfuno yenkqubo.
UBUNCINCI WOKUCALA
Ucoceko lwe-165 mm ngaphezulu, i-100 mm ngaphantsi, i-2.5 mm emacaleni kunye ne-450 mm ngaphambili kwibhokisi yebhoyila kufuneka ivunyelwe ukusevisa.
INGCACISO NGEZANTSI
Ukukhutshwa okuphantsi emva kokufakwa kungancitshiswa ukuya kwi-5 mm. Oku kufuneka kufunyanwe ngephaneli eshenxiseka lula, ukwenzela ukuba igeyiji yoxinzelelo lwenkqubo ibonakale kwaye ibonelele ngococeko oluyi-100 mm olufunekayo ekusekweni.
ISICELO SENKONZO UMSEBENZI
Xa ibhoyila ifakwe ngaphezulu konyaka omnye umyalezo olandelayo uya kuvela kwiscreen:UKUBALEKA KWIGAS
Ukuba kukho ukuvuza kwerhasi okanye impazamo, qhagamshelana neNkonzo kaXakeka yeGasi yeSizwe ngaphandle kokulibazisa.
Umnxeba 0800 111 999.
Qinisekisa ukuba;
– Onke amadangatye eze acinywa.
– Musa ukusebenzisa izitshixo zombane.
– Vula zonke iifestile kunye neengcango.
UKUCOCA
Ukucoca okuqhelekileyo ngokulula uthuli ngelaphu elomileyo. Ukususa amanqaku anenkani kunye namabala, sula ngentengisoamp ilaphu kwaye ugqibezele ngelaphu elomileyo. SUKUZISEBENZISA izinto zokucoca nge-abrasive.
UKULONDOLOZA
Ukuphindaphindwa kwenkonzo kuya kuxhomekeka kwimeko yofakelo nokusetyenziswa kwayo kodwa kufuneka kuqhutywe ubuncinane ngonyaka yiNjineli eBhalisiweyo yeGesi eKhuselekileyo.

1.7 UKUXABISA

1.8 BONISA IMISEBENZI – INDLELA YOKUSEBENZA EQHELEKILEYO

I-CH Knob ijikelezwe
(ngaphandle koluvo lwangaphandle oluqhagamshelweyo)
Uyilungisa njani iBoiler
Amaqondo obushushu

Isibonisi skrola kubuninzi bemiyalezo emi-3 phantsi kwayo nayiphi na imeko yokusebenza, njengoko kubonisiwe ngasentla
Phawula. Amaqondo obushushu aboniswe ngezantsi ngawokwenza imizekeliso kuphela. Amaqondo obushushu alinganisiweyo aya kuboniswa kwibhoyila.

1.9 BONISA IMISEBENZI – IMIYALEZO EYIPHUTHA

Kwi-Ideal Heating sithatha impembelelo yethu yokusingqongileyo njengento ebalulekileyo, ngoko ke xa uhlohla nayiphi na imveliso yokuFundisa ngokuBuyisa nceda uqiniseke ukuba ulahla nasiphi na isixhobo sangaphambili ngendlela ehambelana nokusingqongileyo. Amakhaya angaqhagamshelana nabasemagunyeni basekuhlaleni ukuze bafumanise ukuba njani. 'Yabona https://www.gov.uk/managing-your-waste-an-overview ukufumana isikhokelo malunga nendlela yokubuyisela ngokufanelekileyo inkunkuma yeshishini lakho.
UQeqesho lobuGcisa
I-Academy yethu yeeNgcali inikezela ngoluhlu lweenketho zoqeqesho ezilungiselelwe kwaye zihanjiswe ziingcali zethu zokufudumeza.
Ngeenkcukacha nceda uqhagamshelane: ingcali-academy.co.uk
I-Ideal Boilers Ltd., ilandela umgaqo-nkqubo wokuqhubeka nokuphucula kuyilo kunye nokusebenza kweemveliso zayo. Ilungelo ke ngoko ligcinelwe ukwahluka kwenkcazo ngaphandle kwesaziso.

Ideal luphawu lwentengiso lwe-Ideal Boilers.
IOfisi ebhalisiweyo
Ideal Boilers Ltd., National Avenue, Hull, East Yorkshire, HU5 4JB
Umnxeba 01482 492251 Ifeksi 01482 448858
Inombolo yobhaliso yaseLondon 322 137
Ummeli ogunyazisiweyo we-EU: i-Atlantic SFDT
44 Boulevard des Etats-Unis, 85 000 La Roche-Sur-Yon, France +33 (0)2 51 44 34 34
INombolo yoNcedo yobuGcisa efanelekileyo: 01482 498663
Umnxeba woNcedo oLungileyo wabaThengi: 01482 498660
Amacandelo afanelekileyo: 01482 498665
idealheating.com
Ideal luphawu lwentengiso lwe-Ideal Boilers. IOfisi ebhalisiweyo
Ideal Boilers Ltd., National Avenue, Hull, East Yorkshire, HU5 4JB
Umnxeba 01482 492251 Ifeksi 01482 448858
Inombolo yobhaliso yaseLondon 322 137
Ummeli ogunyazisiweyo we-EU: i-Atlantic SFDT
44 Boulevard des Etats-Unis, 85 000 La Roche-Sur-Yon, France +33 (0)2 51 44 34 34
INombolo yoNcedo yobuGcisa efanelekileyo: 01482 498663
Umnxeba woNcedo oLungileyo wabaThengi: 01482 498660
Amacandelo afanelekileyo: 01482 498665
idealheating.com

Amaxwebhu / Izibonelelo

Ideal C24 Logic Max Combi2 [pdf] Incwadi Yomyalelo C24 Logic Max Combi2, C24, Logic Max Combi2, Max Combi2

Iimbekiselo

• Incwadi yokusebenzisa