WyreStorm NHD-0401-MV NetworkHD 4-Input 4K60 Multiview Switcher
Overview
This user manual provides information regarding the NHD-0401-MV and its configuration. The NHD-0401-MV can be configured to operate within a NetworkHD system with the NHD-CTL-PRO, encoders, and decoders or as a standalone multiview switcher.
Configuring for NetworkHD
To configure the NHD-0401-MV for use within a NetworkHD system, please ensure these prerequisites are met.
- A configured network switch(es)
- NetworkHD 400 or 500 series components
- NHD-CTL-PRO (NHD-000-CTL is not supported)
To begin configuring the NHD-0401-MV, ensure that it’s IP address is in the same range as the NHD-CTL-PRO, encoders, and decoders. By default, the NHD-0401-MV is set to DHCP. In the absence of a DHCP server it will revert to an AutoIP range of 169.254/16.
- Log into the web interface of the NHD-CTL-PRO
- Select the tab that says “NHD-0401-MV”. If you do not see this tab, then the NHD-CTL-PRO was not able to locate the switcher. Verify both devices are in the same IP address range.
- Double click the Hostname of the switcher and enter in a custom alias to identify the device more easily. This alias will also be shown in the NetworkHD Touch user interface.
- The next step is to “bind” decoders and an encoder to the inputs and output of the switcher. To do this click the “bind” button
- From the Receivers section, click and drag decoders to the appropriate HDMI inputs on the switcher. Ensure the logical connection matches the physical connection.
- (Optional) Click and drag an encoder to the HDMI output of the switcher. If the output of the switcher will connect directly to a display this is not necessary. However, if you wish to have the multiview output from the switcher feed back into a NetworkHD encoder to be distributed to any display this is necessary.
- Once binding is complete, click the Apply button.
- Next, navigate to the Multiview tab of the NHD-CTL-PRO. The NHD-0401-MV will appear in the Multiview Receivers section.
| Active Layout | Select the drop-down menu to select a multiview layout to configure |
| Multiview Switching | Drag and drop transmitters to assign video to multiview windows |
| Encoders | Available NetworkHD encoders that can be assigned to a window |
| Audio Settings | Selects the active audio output for the selected layout or mutes audio |
Configuring as Standalone
To configure the NHD-0401-MV as a standalone multiview switcher, log into its web interface by typing its IP address into a web browser. By default, the switcher is set to DHCP. In the absence of a DHCP server it will revert to an AutoIP range of 169.254/16. The default username and password are both admin.
| Active Layout | Click to select the active multiview layout |
| Window Input | A, B, C, D refers to window locations. Select which HDMI input is assigned to each window |
| Image Settings | Choose to maintain source aspect ratio or fill the multiview window |
| PiP Settings | Chooses the location and size of the picture-in-picture window in the PiP layout |
| Audio Input | Chooses the active audio input for a layout. |
Documents / Resources
 | WyreStorm NHD-0401-MV NetworkHD 4-Input 4K60 Multiview Switcher [pdf] User Guide NHD-0401-MV NetworkHD 4-Input 4K60 Multiview Switcher, NHD-0401-MV, NetworkHD 4-Input 4K60 Multiview Switcher, 4K60 Multiview Switcher, Multiview Switcher, Switcher |
