winees WP280013267 Outdoor Security Camera User Manual
winees WP280013267 Outdoor Security Camera

CAUTIONS

To avoid personal injury and/or possible product damage, the following cautions must be followed,

  1. Please use sorely the provided adapter instead of others in case of any damage to the product
  2. Keep out of reach of children. This product contains small magnets and other small parts, which can cause choking or injury if ingested.
  3. To prevent early failure.the camera should only be installed in operating environments ranging between -20°C – 50°C(-4°F – 122°F).
  4. Do not install
    • close to heat source
    • near the metal objects and mirrors that cause radio signal attenuation or shading.
  5. Do not disassemble or reinstall the camera, otherwise it may cause security risks.
  6. Unplug the power cord before cleaning. Do not clean the camera with any liquids, spray cleaner or wet cloth.
  7. The slot and opening are used for ventilation, not allowed to be blocked or covered.

Introduction

Product overview

Package Contents

  • Winees spotlight cam *1
    Winees spotlight cam
  • AC adapter *1
    AC adapter
  • Screw*2  wall anchor 1’2
    Screw
  • Reset pin *1
    Reset pin

Status LED Description

Status Description
Solid Red Power on/System booting/ Factory reseting
Flashing Red Wireless connection, cloud connecting fail
Solid Green Wireless connected
Flashing Green System ready for WiFi setup/ Firmware update
Red and Green flashing alternately Unable to connect to the cloud

Set up Spotlight Cam in the Ai Dot App

  1. Scan the OR code below
    QR Code
    Icon
    Or search for”AiDot” in App Store or Google Play
    Apple logo
    Google play logo
  2. Power on the camera, you will hear “Waiting for Wi-Fi configuration” with the camera’s indicator light flashing in green.
    Power on the camera
  3. In the AiDot app, press’+’ – ‘devices·, select Winees Spctlight Cam, and follow the instructions on App
    AiDot app menu
  4. Place the spotlight cam in the area where you plan to install to test the video quality, ensure that the camera can work normally after the final installation.

Install Spotlight Cam on the wall or celling

  1. Placement
    The recommended installation height is 3 meters (9 feet) above the ground. Either too high or too low height may affect the operation of the motion detector.
    Install Spotlight Cam
    Install Spotlight Cam
    Install Spotlight Cam
  2. Install the bracket
    When install the bracket on the wall/ceiling, please pay attention to the installation direction of the base. If installing on a masonry surface, drill holes on the wall first insert the anchor into the hole, and then install screw to fix the base.
    If installing on a wooden surface, install screw to fix the base directly.
    Note, When install it upside down on the ceiling, you’ll need to set the image angle to 180° in the camera settings after adding the camera on the app
    Install Spotlight Cam on the wall
    Install Spotlight Cam
    Install Spotlight Cam
  3. Tighten the camera.
    Arrange the cables behind the camera. You can route the wire from the top or bottom. Align the arrow on the camera base with that on the mounting bracket, snap it into place with a clear ‘click” sound, and then tighten it with the Security Screw
    Tighten the camera
    Tighten the camera
  4. Adjust the camera angle
    Manually adjust the up and down angle of the camera to obtain an accurate monitoring image and motion detect range. The tightness of the up and down rotation can be adjusted by the screw at the connection.
    Adjust the camera angle
  5. Power on the camera
    Power on the camera and wait for the camera to work.
    Power on the camera
    Power on the camera

Requirement and Tech Specs

Wi-Fi Network Requirements

  • Supports IEEE 802.11b/g/n
  • Your Wi-Fi network broadcasts at 2.40Hz. 5GFIz band is not supported
  • Your network upload speed is suggested to be greater than 1 Mbps to have fluent video streaming,

Power (Only for CE)

  • 100- 240VAC 50/60Hz power supply for the AC adapter
  • DC 12V/1A input for the camera
  • Max. power consumption:10W
  • Frequency range: 2412-2472MHz
  • Maximum RF transmit power: 802.11b16±2dBm, 802.11g 54M 14t2dBm, 802.11n HT2012±2d8m 802.11n HT4012t2dBm
  • Maximum radio-frequency power: 20 dBm

Camera

  • 2K OHO ®25 frames per second
  • Maximum resolution: 25601440
  • 1/3′ Color CMOS sensor
  • 135° (diagonal) wide angle lens
  • Video compression. H 265/H 264
  • Infra-red night vision: 10m(32.8tt)
  • Motion detection: 7m Max. –
  • Rotation: 270° pan

Audio

  • Built-in microphone and speaker
  • Two-way talk

Lighting

  • White light LEO: 5000K. 4001m

Siren

  • 100dB IV Ocm Max

Storage

  • Micro SD card storage up to 128 GB (Micro SD card is not included)

Operating Environment

  • Temperature: -20°C – 50°C(-4°F -122°F)
  • Humidity: s 95% non-condensing

Trouble Shooting

If the default adding camera operation fails

  • Make sure your wireless router has the Internet access, and the Wi-Fi signal at the location where you install the camera is good.
  • Make sure the camera is plugged in and the status LED is on or flashing – Reset the camera if the LED is NOT flashing green. Then follow the App to add it – Make sure the camera is not added to other user’s account. if it IS, the owner of the camera has to inbind it first
  • When this step is done, the carers should be added to your account. if the Micro SD card is not detected by the camera
  • Make sure the card is good and format it again in the FAT-32 format.

How to do the forced reset?

  • If you cannot reset the camera from the setting page. please hold the reset button in the pin hole with the reset pin for 3 seconds and release. The COMM will play a voice prompt’ Restoring factory settings’.

The time of the camera video stamp is not right

  • Please set the right time zone in the settings.

How long can a MicroSD card (not included) of different capacity record?

MlcroSD card capacity Duration of video recording
16GB 2511
32GB 50h
64GB 100h
128GB 200h

ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation Science and Economic Development Canada’s Licence-exempt RSS(s). Operation is subject to the folbwing two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with MD RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your booly.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received. including interference that may cause undesired operation.

Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment NOTE: This equipment has been tested and found to corrply with the limits for a Class B digital device. pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning te equipment off and oft the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is corrected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

Customer Service

Business name, APEX CE SPECIALISTS LIMITED
Business address: 89 Princess Street,
Manchester, Ml 4HT, UK
Email: [email protected]
Tel, +441616371080
Icon

Business name, APEX CE SPECIALISTS LIMITED
Business address, UNrr 30 NORTH POINT HOUSE,
NCRTH POINT BUSINESS PARK, NEW MALLOW RCAD,
CORK, T23 AT2P IRELAND
Email: [email protected]
Tel, +353212066339
Icon

Contact Us/ Kontalctieren Sie uns
Linkzone Technology Co., Limited
RCCM 20 5/F WAYSON COMMERCIAL BLDG 28
CON NAUGHT ROAD WEST SH EU NG WAN HK
Phone, 1-855-334-9800
Website: www.iwinees.com
Email: [email protected]
Made in China

Icon

Documents / Resources

winees WP280013267 Outdoor Security Camera [pdf] User Manual
WP280013267, 2AYZ8WP280013267, WP280013267 Outdoor Security Camera, WP280013267, WP280013261, WP280013263, Outdoor Security Camera

References

Leave a comment

Your email address will not be published.