G10 GPS Speed Meter
User Guide
Warning: This product working voltage is 5V, and it is forbidden to use a voltage higher than 5V for power supply.
Display functions:
- Multi-function display: clock, driving time, travel distance, satellite numbers, acceleration time, longitude, latitude,Dial left or right to switch
- Function icons: fatigue driving, driving time, clock, acceleration time, direction angle, longitude, latitude, driving distance, altitude
- Speed progress bar
- Speed display
- Speeding alarm icon
- Vehicle speed unit (MPH=mile ,Km/h=kilometre), compass, satellite number icon
- The compass can be used normally after the satellite is searched, (N=North, E=East, W=West, S=South)
- The GPS satellite icon stops flashing before it can be used normally
- Satellite numbers
Wave button function:
- Short press in: confirm the option after entering the setting menu
- long press in: enter the setting, after adjusting, press vertically for 2 seconds to save and exit
- Push left:: switch clock, driving time, acceleration time (move option after entering setting)
- Long push left: push left for 2 seconds to turn off the buzzer alarm, do it again to turn on
- Push right: switch driving distance, altitude, longitude, latitude (move option after entering the setting)
Enter setting mode:
Long press in to enter into the setting mode, press right to choose the menu, and short press in to confirm. Once finishing the setting, long press in to exit.Menu Function Adjustment range Explanation Default value Set parameter value interface 1 speed 50-150 Adjust the parameter value when there is an error between HUD and dashboard.
Ex: dashboard displays 100 KM/H, HUD displays 105 KM/H. Please adjust the parameter value to 102.(107-5)105 
2 Section 1 over speed alarm 0-250 When the vehicle speed reach to 150KM/H, HUD will give the alarm 150 
3 Section 2 over speed alarm 0-250 When the vehicle speed reach to 180 KM/H, HUD will give the alarm 180 
4 Section 3 over speed alarm 0-250 When the vehicle speed reach to 200 KM/H, HUD will give the alarm 200 
5 Fatigue driving alarm 1.0-8.0 HUD will give fatigue driving alarm each 8 hours 8 
6 Brightness adjustment 0-11 0=automatic sensitivity adjustment
1-11=manual adjustment0 
7 Speed unit 0-1 0=KM/H (kilometers)
1=MPH (miles)0 
8 Time Adjust :00-12:00 When the device searched the satellite successfully, adjust the device time as your local time and exit. 0 
9 Factory reset 0-1 default=0, →1, long press in for 2 seconds to save and exit 
GPS FAQ:
– Check whether the USB cable is damaged, replace the USB cable for testing, and prohibit the use of voltage higher than 5V for power supply
– After HUD power-on, the satellite icon flashes will start to find the satellite. Please driving the car to the road. It will work after it stops flashing
– When the device search the satellite successfully(the default 8:00 will change to China local time), set it to your local time and save and exit.
– (1) If the unit is correct,km KM/mile MPH, (speed unit switch reference settings item)
– (2) The car factory had increased speed(5-7%)than real for drivers’ safety,satellite data is strictly follow the international standards
– (3) Fine-tuning the vehicle speed, e.g. meter display 100 Km/h, machine display 105Km/h,default value 107-5=102
– After the vehicle speed exceeds 5KM / H, the direction can be displayed normally.
– Under the underground parking lot, tunnel, under the overpass, there will be unstable satellite drift when there is obstruction.
– Push left for 2 seconds to turn off the buzzer, do it again to turn on.
Documents / Resources
 | wiiyii G10 GPS Speed Meter [pdf] User Guide G10, G10 GPS Speed Meter, GPS Speed Meter, Speed Meter |
