widomSmart Double Switch N 7
SKU: WDSN700
Quickstart
This is a
secure
Binary Switch DT
for
.
To run this device please connect it to your mains power supply.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way
communication) and every mains powered node can act as a repeater for other nodes
(meshed network) in case the receiver is not in direct wireless range of the
transmitter.
This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.
If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.
Product Description
Smart Double Switch 7 is an ON/OFF control device designed to independently control two separate loads, suited for being controlled by both remote and local switches.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 0 | |
| 2 | 8 | |
| 3 | 8 | |
| 4 | 8 | |
| 5 | 8 | |
| 6 | 8 | |
| 7 | 8 |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.
IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.
Parameter 1: IN1_TYPE
Define the input 1 type. (1: button, 2: toggle switch, 0: no switch input)
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 10: IN1_TOGGLE
Define which events on the input 1 toggle output 1. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 11: IN1_ON_EXCLUSION
Define which input 1 event do not switchOn output 1. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 12: IN1_OFF_EXCLUSION
Define which input 1 event do not switchOff output 1. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 15: IN2_TOGGLE
Define which events on the input 2 toggle output 2. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 16: IN2_ON_EXCLUSION
Define which input 2 event do not switchOn output 2. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 17: IN2_OFF_EXCLUSION
Define which input 2 event do not witchOff output 2. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 2: IN2_TYPE
Define the input 2 type. (1: button, 2: toggle switch, 0: no switch input)
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 21: OUT1_TYPE
Define the output 1 type. (0: direct load control or normally Open relay, 1: normally Closed relay)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 22: OUT2_TYPE
Define the output 2 type. (0: direct load control or normally Open relay, 1: normally Closed relay)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 23: STARTUP_OUT1
Define the output level on startup (0: OFF, 1: ON, 2: Previous status, 3: equal to input)
Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 24: STARTUP_OUT2
Define the output level on startup (0: OFF, 1: ON, 2: Previous status, 3: equal to input)
Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 25: LOCAL_SCENE
Define the Local scene configuration. (0: independent channel, 1: never both on, 2: sequencing)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 30: TIMER_CH1_SETUP
EP1 output events that start timer (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up, 32: Network, 64: sys)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 31: OFF_EP1_TIMEOUT
Time in tenth of second after which the output on EP1 will be switched Off.
Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 32: ON_EP1_TIMEOUT
Time in tenth of second after which the output on EP1 will be switched On.
Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 33: TIMER_CH2_SETUP
EP2 output Events that start timer (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up, 32: Network, 64: sys)
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 34: OFF_EP2_TIMEOUT
Time in tenth of second after which the output on EP2 will be switched Off.
Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 35: ON_EP2_TIMEOUT
Time in tenth of second after which the output on EP2 will be switched On.
Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 40: G1_EP1_SETUP
Input 1 events that control EP1-G1 association group. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 41: G2_EP1_SETUP
Input 1 events that control EP1-G2 association group. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 42: G1_EP2_SETUP
Input 2 events that control EP2-G1 association group. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 43: G2_EP2_SETUP
Input 2 events that control EP2-G2 association group. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 44: G1_EP1_ASS_VALUE
Value used to control EP1-G1 association group. (0-99: specific value, 100: ON, 101: propagate, 102: toggle remote)
Size: 1 Byte, Default Value: 101
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 45: G2_EP1_ASS_VALUE
Value used to control EP1-G2 association group. (0-99: specific value, 100: ON, 101: propagate, 102: toggle remote)
Size: 1 Byte, Default Value: 101
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 46: G1_EP2_ASS_VALUE
Value used to control EP2-G1 association group. (0-99: specific value, 100: ON, 101: propagate, 102: toggle remote)
Size: 1 Byte, Default Value: 101
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 47: G2_EP2_ASS_VALUE
Value used to control EP2-G2 association group. (0-99: specific value, 100: ON, 101: propagate, 102: toggle remote)
Size: 1 Byte, Default Value: 101
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 60: SCENE_SETUP
Define event sent by central scene notification. (0:none, 1:1 click , 2:2 clicks, 4:3 clicks, 8: Hold down, 16: Up)
Size: 1 Byte, Default Value: 31
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 70: E_REPORT_DELAY
Time in minutes after which the next Energy report will be sent.
Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 71: W_REPORT_DELAY
Time in minutes after which the next Power report will be sent.
Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 75: W_ISTANT_REPORT
The percentage change from the last sent report that trigger an new Power report.
Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 0 | 0 |
Technical Data
| Hardware Platform | ZGM130S037HGN2 / ZGM130S037HGN1 |
| Device Type | Binary Switch DT |
| Network Operation | Always On Slave |
| Firmware Version | HW: 01 FW: 02.01 |
| Z-Wave Version | 7.16.3 |
| Certification ID | ZC14-22120173 |
| Z-Wave Product Id | 0x0149.0x0004.0x0005 |
| Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Application Status
- Association Grp Info V3
- Association V2
- Basic V2
- Switch Binary V2
- Central Scene V3
- Configuration V4
- Device Reset Locally
- Firmware Update Md V5
- Indicator V3
- Manufacturer Specific V2
- Meter V5
- Multi Channel Association V3
- Multi Channel V4
- Powerlevel
- Security 2
- Supervision
- Transport Service V2
- Version V3
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. - Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. - Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. - Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and
a controlled device. - Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. - Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.
