Categories: WHITESTONE

WHITESTONE Dome Silk Ultra Thin Glass User Guide

WHITESTONE Dome Silk Ultra Thin Glass

Ultra Thin Glass Installation User Guide

Please make sure to check manual and installation video before using the product.
Please make sure to check manual and installation video before using the product.

After checking the Quick guide, check the User guide.<Quick guide / User guide>

Please check the model and components before using the product.

  • Match your device model with the product in advance.
  • Please check all the components listed on page3 and if there is any problem with the components, please contact us before the installation.

Cautions before Dome silk installation

  • Watch the Installation video and manual carefully before starting to install.
  • Please see all introductions, since each device has different installation way.
  • install the glass after removing any film on the screen.
  • Please avoid a dusty place.
  • Be careful of any impacts while getting out the jig from the box in order to prevent any damage.
  • Be careful not to force the jig apart or break it.
  • If there is a problem with the subsidiary materials, please do not attempt installation and contact customer service immediately.
  • YOU MUST KEEP THE REMOVAL PACK. Make sure to use it when removing the GLASS.

Components

Reference
  • There may be differences in components depending on the model.
  • To improve the product, the component’s appearance or specifications etc. can be changed without prior notice.
  • The removal pack must be stored as it is required to remove the glass.

Installation

STEP1 Remove the protection film attached to your device using the UTG Remover included in the Remove Pack.

  • Please keep UTG Remover after use.

STEP 2 Connect the Align block to top part of the JIG.

STEP3 Insert the device into the JIG in correct direction.

STEP4 Clean the display with alcohol wipe and cleaning cloth. Then, remove any dust with dust removal sticker.STEP 5 Hold the top part of the film as shown, and bend the blue sticker as shown in [Figure 1]. Like [Figure 2] Make sure that the protective film and glass are properly separated and slowly remove the protective film. If it is as shown in [Figure 3], attach the protective film as if it is in the first state and remove it carefully so that only the protective film can be removed.

  • Please do not touch the adhesion surface.

STEP6 Flip the glass with the protective film removed so that the top/bottom text are visible to the front.

  1. Insert the top part of the film into the Align block.
  2. Insert the bottom part of the film into the bottom part of the JIG.
    • Please do not touch adhesion surface.
    • Make sure the GLASS does not stick onto the device.

STEP7 Hold the top end of the film and slowly and forcefully push up with the squeegee from the bottom of the jig to the top 2/3 while maintaining squeegee in a lean angle. Make sure there is no bubble at the folding area If bubble appears, proceed to STEP 7-1. If not, push the squeegee all the way to the end.

ATTENTION:

  • Bubble might have appeared if you push the squeegee too fast.
  • To avoid the bubbles, make sure to push the squeegee slowly around the folding area.

STEP7-1 (When air bubbles are generated when attaching the folding part)

Remove the guide film from the hole on the top of the jig. Detach the GLASS below the bubble by about 2cm and while holding the top of the film with your hands, be careful not to slide the jig, and gently push it with a squeegee to attach it.

CAUTION:

  • Bubble might be appeared if you push the squeegee too fast.
  • To avoid the bubbles, make sure to push the squeegee slowly around the folding area.

STEP 8 Remove the guide film from Jig’s hole while pressing the ①-top/②-bottom of the glass with a squeegee. ③Push the glass entirely to the short side of the squeeze.

STEP 9 Bend the guide film attached to the glass and remove it from the top. Finish by pressing the glass edge with the short part of the squeegee. Remove the device from the JIG.

  • Microbubbles will disappear within a week. Please make sure NOT to press the bubbles with nails, Thin glass on the bubble could be broken by external pressure.
  • Recommend to use the device after 5 min upon installation.

Remover InstallaRemove Installationtion

STEP 1 Hold the handle of the Removal Film and peel off the yellow paper about 1/3 and attach it in alignment with the GLASS.

STEP 2 Push the UTG REMOVER between the device and the GLASS to make a gap, and then slowly pull up the both GLASS and UTG REMOVER together to remove while holding the device immovable. STEP 3 After removing dome silk, if there is glass powder or dust remove it using scotch tape, etc.
CAUTION: Do not wipe the glass power or dust, but gently remove it. When wiping, be careful as scratches may occur.

NOTE: Please check the Installation Guide.

Precautions after installation 

  • Glass may be damaged by impacts.
  • Although glass includes shatter-resistant film, recommend users change the glass to a new one once the glass is broken in order to prevent any harm.
  • Bubbles or lifting may occur by physical impacts such as drop impact, incompatible phone cases use, excessive strength while cleaning with alcohol wipes or etc.
  • No refund or exchange for any type of user damage.

Precautions when removing the tempered glass 

  • Please refer to the removal manual and remove it.

Global A/S 

CONTACT US: feedback@whitestonedome.com 
HOMEPAGE: www.whitestonedome.com WARRANTY REQUEST
We always provide friendly and fast service to your questions.

Documents / Resources

WHITESTONE Dome Silk Ultra Thin Glass [pdf] User Guide
Dome Silk Ultra Thin Glass

References

Share

Recent Posts

DYNAVIN D8-DF17 Pro 10.1-inch Android Car Radio Instruction Manual

D8-DF17 Pro 10.1-inch Android Car Radio

2 mins ago

WOLFBOX D07 Mirror Dash Cam Instruction Manual

D07 Mirror Dash Cam Mirror Dash Cam D07 Instruction Manual 2 3 4 9 10…

9 mins ago

ICEKING ICE-IK9653W.E Fridge Freezer User Manual

ICE-IK9653W.E Fridge Freezer Fridge Freezer in White If you experience any issues with your product…

25 mins ago

Sprecher Schuh CS7 Standard Control Relays User Manual

CS7 Standard Control Relays Industrial Control Relays Series CS7 - Standard Relay Series CS7 Standard…

27 mins ago

MERCURY KM3KM Ham Radio User Manual

KM3KM Ham Radio USER MANUAL Features Operating Bands 160m ­ 6m (Ham Bands) RF Auto…

28 mins ago

MUSICAL FIDELITY MX-Stream Audiophile Bit-Perfect Streamer Instruction Manual

MX-Stream Audiophile Bit-Perfect Streamer MX-Stream Control Options Overview The MX-Stream has a wide variety of…

28 mins ago