WEINTEK MT8052iP Series HMI Touchscreen Panel
Product Specifications
- Product Series: MT8052iP
- Environment: NEMA 4 rated (indoor use only)
- Electrical Environment: European CE requirements compliant
- Altitude: Refer to the Datasheet for details
- IP Rating: Refer to Datasheet for details
Unpacking and Inspection
Unpack the delivery and check for any damage. Contact the supplier in case of damage. Place the operator panel on a stable surface during installation to prevent damage.
Package Contents:
- Installation Instruction (2-sided A4) x1
- Human Machine Interface x1
- Power Connector x1
- Brackets & Screws pack x1
Installation Instructions
Follow the instructions provided to correctly install the HMI unit.
Power Connections
Connect the positive DC line to the ‘+’ terminal and the DC ground to the ‘-‘ terminal.
System Settings
When HMI powers up and displays an image, click on the system settings button.
- Default System Password: 111111
- Set your own passwords in the Security tab.
- Connect to the network through an RJ-45 cable in the Network tab.
EasyBuilder Pro Software Settings
Configure settings using the EasyBuilder Pro software.
Communication Connections
Refer to the manual for COM1 and COM3 RS-485 connections and use the appropriate screws for D-SUB connector installation.
Touchscreen Calibration Mode
To enter touchscreen calibration mode, press and hold anywhere on the screen when the HMI starts. Follow onscreen instructions for calibration.
Battery Replacement
- Battery Specification: Type CR1220, Rated 3V
Battery replacement should be done by qualified personnel. For detailed instructions, refer to the provided link.
Installation and Startup Guide
This document covers the installation of the MT8052iP Series HMI. For the detailed specifications and operation, please refer to the Datasheet, Brochure, and EasyBuilder Pro User Manual. Please read all warnings, precautions, and instructions on the device carefully before use.
Install Environment:
Unpacking the Unit
- Unpack and check the delivery. If damage is found, please contact the supplier.
- NOTE: Place the operator panel on a stable surface during installation. Dropping it or letting it fall may cause damage.
- The package includes:
- Installation Instruction, 2-sided A4 *1
- Human Machine Interface *1
- Power Connector *1
- Brackets & Screws *1 pack Installation Instructions
- Use a control box that provides enough stiffness. Cutout Dimension: 119 mm x 93 mm. Secure the operator panel in position, using all the fastening holes and the provided brackets and screws. Screw
- Torque: 2.6 ~ 3.9 lbf. In. (For reaching a waterproof effect and preventing the panel from being deformed.)
- Plan for adequate space around the unit and inside the enclosure, for ventilation and cables. Consider the heat fromother devices inside the enclosure. The ambient temperature around the unit must be 0 ~ 55°C.
- Minimum required clearances (along the overlay): Top 15 mm / Bottom 50 mm / Sides 15 mm Maximum panel thickness: 4.5 mm
Power Connections
- Power Connector Specifications:
- Wire AWG: 24~12
- Wiring Conductor Minimum Temperature: 75°C
- Screw Torque: 4.5 lbf-in (max.)
- Copper conducts only.
- NOTE: Connect the positive DC line to the ‘+’ terminal and the DC ground to the ‘-’ terminal.
System Settings
When HMI is powered up and displays an image, click the system setting button. (Default System Password: 111111)
- Go to the Security tab, the default password is 111111, click the buttons to set your own passwords.
In the MISC2 tab, if “Enable [Reset HMI to default] button in calibration mode” is selected, the [RESET HMI TO DEFAULT] button can be found in calibration mode, as shown in Part 8. - Go to the Network tab, and you may choose to auto-get a DDHCPIP, or designate your own IP. It is necessary to connect the HMI to your network through an RJ-45 cable.
EasyBuilder Pro Software Settings
- Launch EasyBuilder Pro software, select your project file, press F7 shortcut key to open the download dialog box: Select Ethernet > IP tab > Enter your HMI IP > Click Download to download this project file to HMI.
- Using screensavers and backlight savers is recommended in order to avoid image persistence caused by displaying the same image on the HMI for a long time.
- Flash memory has a limited write lifespan, and frequent data writing (e.g., Event Log, Data Sampling) can accelerate degradation. Consider write frequency and lifespan management in system design to prevent data loss. Refer to “3.2.1. Prolong the Lifespan of Flash Memory” in the Product Security User Manual for guidance. (Please refer to the EasyBuilder Pro User Manual for software operation details.)
Communication Connections
NOTE:
- COM1 and COM3 RS-485 2W support MPI 187.5K, please use one at a time.
- Use #4-40 UNC screws for the D-SUB connector installation.
Touchscreen Calibration Mode
- Press and hold anywhere on the screen when the HMI starts until it enters touchscreen calibration mode. If “Enable
- [Reset HMI to default] button in calibration mode is selected as described in Part 5 System Settings, then [RESET HMI TO DEFAULT] and [SYSTEM SETTINGS] buttons can be found in calibration mode. Follow the onscreen guide and press [yes] to restore factory default, and please note that the projects and data stored in the unit will all be cleared after this.
Battery Replacement
- Battery Specification: Type CR1220, Rated 3V
- Battery replacement shall be performed by qualified personnel (engineer) only, a nd care must be taken when handling lithium batteries. For more information on battery replacement and disposal considerations, please refer to the following link:
- http://www.weintek.com/download/MT8000/eng/FAQ/FAQ_103_Replace_Battery_en.pdf
Limited Warranty
- This product is limited warranted against defects in design and manufacture.
- The proven defective product will either be repaired or replaced, at Weintek’s discretion. This warranty shall not cover any product which is
- (a) Out of warranty period, which is 12 months from the manufacturing month of the HMI products.
- (b) Damage caused by Force Majeure, accident, negligence, improper installation, or misuse.
- (c) Product has been repaired or taken apart by unauthorized technicians.
- (d) Products whose identification markings have been removed or damaged.
Frequently Asked Questions
button.*2. Confirm by pressing [yes] when prompted.*3. Note that all projects and data stored in the unit will be cleared after resetting to factory default ” image-0=”” count=”1″ html=”true” css_class=””]Documents / Resources
 | WEINTEK MT8052iP Series HMI Touchscreen Panel [pdf] Installation Guide MT8052iP, MT8052iP Series HMI Touchscreen Panel, MT8052iP Series, HMI Touchscreen Panel, Touchscreen Panel, Panel |