WATTSHOP MK2 Extension Mono Stack

EXTENSION INFORMATION

BUILD OPTION
For mono-riser stack systems, there is only one build option available. It is critical to ascertain the correct size bracket to meet your requirements.

BRACKET

Core components

Extensions

Handgrips

Armrests

Baseball-specific adjustable riser fixed angled riser

Crossbrace computer mount

Bracket

HANDGRIP SELECTION

STANDARD POLE+ STANDARD POLE (LONG)
The standard pole handgrip mirrors the traditional pole end shifter. It is compatible with the following shifters:

• SHIMANO R9160
• SHIMANO SW671
• SRAM cues

The handgrips will be available in a standard length for athletes competing under UCI regulations who want to maximise their extension and le, and a longer length for athletes competing under non-UCI-regulated events.

Install method
The bracket attaches to your existing mono stack riser. In turn, the baseball-specific riser or fixed-angled riser will attach to the bracket.

ERGO
ThErgogo handgrip is available in different versions. They are named as follows:

• SHIMANO R9150
• SRAM WIRELESS BLIPS
• SRAM WIRED BLIPS
• TRACK

All versions except the track handgrip will be suppliewithth an inner and outer component. Youshifterer but will attach to the inner componentry while the outer component slides over the top. This increases the shifter contact freshener sh lifting.

UCI HAND HEIGHT COMPLIANCE
When competing under UCI regulations you will need to ensure you are compliant with the UCI regulations applicable to your height category.

• CATEGORY l – riders are allowed 700mm mid-point ofthe armrest to the extension tip.
• CATEGORY 2 – riders are allowed 720mm mid-point of the armrest to the extension tip.
• CATEGORY 3 – riders are allowed a 740mm mid-point of the armrest to the extension tip.
• NON-CATEGORY – riders are allowed 700mm mid-point of the armrest to the extension tip.

Please note: mid-point to extension tip measurements are measured vertically All accessories are included in these dimensions.

WattShop Product Compatibility
Compatible with the complete range of WattShop componentry. Due to the control led later in the centre of this mounting option, our cross-brace BTA mount and computer mount are the optimal choices for this build.

• COMPLIANT
• CONDITIONS APPLY
• NON-COMPLIANT

All dimensions are in millimetres (mm) unless otherwise stated.
All standard pole handgrips can be trimmed to fit your desired category. Please note the standard pole dimensions above exclude the shifter.

BRACKET BUILD

REACH
All reach dimensions are measured from the rear riser bolt hold horizontally to the extension tip.

WIDTH
All width dimensions are measured in red from outside to outside at the rear of the eacarmrestst.

For armrests widths narrower than 200mm, the inner edge will require trimming. Al l dimensions are in millimetres (mm) unless otherwise stated.

RISER SELECTION

ADJUSTABLE RISER
The adjustable riser is available in two different options. For the Bracket, bu ild you wi ll rraceI have the baseball-specific riser option.

BASEBALL SPECIFIC ADJUSTABLE RISER
These risers have threaded bosses on the underside which provides easy installation and seamless integration with WattShop componentry.

FIXED ANGLED RISER
Designed to provide you with a clean and seamless integration between the user and extension, the thieved handled riser is available in five different angles, each which comes with 2 degrees of toe-in  This may be the preferred option for riders who know their optimal extensioanglele or want to maximise their positiowithinin the UCI regulations.

• 10 DEGREES
• 15 DEGREES
• 20 DEGREES
• 25 DEGREES
• 30 DEGREES

ARMREST+ COMPUTER MOUNT SELECTION

ARMRESTS
Available in two different styles. Both are slotted to provide width adjustment.

DUAL-SIDED
Each armrest has high-sided inside and outside supporting faces, giving the armrest a “U” shape We recommend this style of armrest for widths 220mm or wider this ensures youwilll benefit from the support of the inside edge.

SINGLE SIDED
Each armrest has a high-sided outside supporting face We recommend this for armrests widths less than 220mm. At less than 220mm your forearms are likely touching so the benefit of the inside supporting face is reduced.

COMPUTER MOUNAvailablele in two different options; Garmin and with only one extension interface option.

CROSSBRACE MOUNT
Comes supplied as standard the Bracket computer mount attaches to both extensions to centralise and provide additional strength. GoPro-style accessories are available to allow GoPro and front-light attachments.

BRACKET SELECTION

BRACKETS
The mono brackets are available in different sizes, and each bracket offers 20mm of reach adjustment Your budget will come with the bracket size of your choice. Across the three sizes anywhere used in conjunctiowithth t, the adjustable rise he systprovidesdes a large-reawindowdow

• EXTRA SHORT (XS)
• MEDIUM (M)
• EXTRA LONG (XL)

When used in combination with the fixed angled risers you find yourself between reach sizes as the reacwindowow is reduced. This applies to you, please
contact us and we can offer SHORT (S) and LONG (L) brackets.
Please note each bracket is specific to the mounting it is named after I.E Sh iv Tri brackets are only compatib with Sh iv Tri bikes.

• @watt_Shop
• @wattShop
• /shopforwatts
• info@shopforwatts.co.uk
• www.shopforwatts.co.uk

Documents / Resources

WATTSHOP MK2 Extension Mono Stack [pdf] User Guide MK2 Extension Mono Stack, MK2, Extension Mono Stack, Mono Stack, Stack

References

• User Manual