WASSERMANN - logoPolyquick 260-T105 Pressure Polymerisation Unit and Compactor
User ManualWASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and CompactorWASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 1

Dear customer,
Thank you for choosing a product from the Wassermann range. Wassermann DentalMaschinen incorporates the highest standards of quality and the latest technology. In order to enjoy maximum performance and years of trouble-free operation, please read this user manual carefully before you connect this device and start work, and operate the device according to the recommended guidelines. The operation safety and the functionality of this device can only be guaranteed if you follow both the general safety guidelines and the applying laws to prevent accidents as well as the precautions given in this user manual. We are not liable for any damages which occur due to inappropriate usage or faulty operation of this device.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Make sure that anyone using this device has read and understood this user manual.
Keep this user manual in a safe place where it can be referred to as required at any time.
PROBOAT PRB08043 BlackJack 42 Inch Brushless 8S Catamaran - icon 3The unit complies with the relevant EU guidelines.
Haier HWO60S4LMB2 60cm Wall Oven - icon 11The unit is subject to the EU guidelines 2012/19/EU (WEEE Directive).

Company address:
Wassermann Dental-Maschinen GmbH
Rudorffweg 15-17
21031 Hamburg, Germany
Phone : +49 (0)40 730 926 -20/ -24 Fax.: +49 (0)40 730 37 24
[email protected]
www.wassermann.hamburg
www.facebook.com/WassermannDentalmaschinen

Features

  • Compact table-top unit for pressure polymerisation up to 105°C in a water bath
  • Very large capacity Ø 240 mm, usable depth 160 mm, suitable for extra large articulators
  • Touch screen for fast and easy operation
  • 13 programmes, each with three individually configurable polymerisation stages
  • The device can also be operated as a pressure compactor
  • Rapid draining: prompt switch between the two modes
  • Separate menu for each mode
  • Intelligent workflow preset by the software helps the user to ensure operational safety
  • Exact remaining time displayed
  • Powerful, electronically controlled heating for optimal water temperature
  • Pressure relief valve for protection in case of malfunction (7 bar)
  • Safety lid with bayonet lock
  • Dry-run protection
  • Engraving in container indicating max. water level
  • Time and cost saving due to thermal insulation
  • Made almost entirely of stainless steel
  • Low maintenance, easy to service

Safety Symbols used in this Manual

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningWarning!
This is a warning of risk situations and dangers.
Failure to observe this warning could be life-threatening. These warnings has to be observed.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Information!
This symbol draws your attention to specific features that has to be observed.

Safety Guidelines

Configuring and operating this equipment requires precise knowledge and observance of the instructions in this user manual. The equipment is designed only for its intended  application.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningWARNING:
Servicing and repairs should be carried out only by authorised specialists.
Disconnect the power plug before starting any maintenance work.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningMake sure that the equipment is connected to the correct power source.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningThe safety valve on the pressure tank opens automatically if the operating pressure is more than 7 bar.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningThe pressure can be activated only if the door is closed completely, since a safety door contact is installed.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningDry-run protection, which switches off at 112°C (brown button on the left side of the device).
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningWARNING: Risk of scalding during the Hot Polymerisation.
Never open the lid while the unit is under pressure!
Open the lid slowly!
Display information have to be followed!
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningFor safety-related reasons (hot water, pressure), only the valves and hoses meant for this purpose must be used for draining. If parts of different design are  used/installed (self-made), there is a risk of scalding! 

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2For safety reasons, the pressure setting is limited to max. 4 bar (at 20 ° C).
Attention: When working above 100°C, the pressure can increase by approx. 2 bar.
Note: Hence the unit should be filled only with water and should be pre-heated to the desired working temperature, before the actual work process.
To do this, select the preheating temperature and pressure accordingly.

Responsibility for Operation or Damage

The responsibility for operating the device lies exclusively with the owner or user if said device is incorrectly serviced, maintained or altered by persons not employed by an authorised dealer or if the device is used in a manner contrary to its specified purpose.
The unit has to be maintained and operated in accordance with this user manual.
Wassermann Dental-Maschinen GmbH is not responsible for damage arising from the nonobservance of these instructions.
Warranty and responsibility provisions contained in the sales and supply conditions of Wassermann Dental-Maschinen GmbH are not extended by these instructions.

Application

The Polyquick 260-T105 is a pressure polymerisation unit for hot and cold polymerisation of plastics. It can be set to a maximum temperature of 105°C and the polymerisation pressure can be adjusted to a maximum of 4 bar. In automatic mode, the polymerisation time can be preselected up to 99 hours. It has a particularly large pressure pot volume  and can hence also accommodate extra large articulators or up to 6 brass flasks including clamp. A touch screen and the newly developed control panel allow the user to set the relevant parameters quickly and easily using self-explanatory symbols.
The Polyquick 260-T105 can also be used as a pressure compactor without heating.
Only use the device for this type of application.

Before Starting

Transport

Before transporting the unit, ensure that it has been unplugged from the power socket.
Make sure that it is packed correctly in order to avoid accidental damage.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Be sure to check for any transport damage when unpacking the goods. Note down any damage if found.

Installation

Open the box, remove the packing materials, and carefully lift out the device and accessories. Check the included accessories.
The device has to stand horizontally on a steady and even surface.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningInstall the device in a place where it will not block the working area and the functionality (take the dimensions into account).
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Do not install the unit outdoors or in places without proper ventilation.
Before start-up, be sure the device reaches room temperature.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2It is advisable to install the unit firmly on the drainage system, since very hot water can drain off from it. This also simplifies the process of complete emptying, e.g. for cleaning.

Storage

The unit location is very important when it comes to workplace safety, even if it is only to be set up there for a short period. The room should be dry, well ventilated and vibrationfree. An even temperature and wooden supports also help. The unit should not be stored or set up outdoors. If the unit is to be stored for an extended period, protect it from moisture and dust.

Installation/ Start-up

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Before commissioning, please install the following connections: Install the pressure hose included in the scope of supply and provide for an appropriate outlet.

After setting the workpiece, fill the device with tap water, at most up to the engraving in the tank. Establish a pneumatic connection of minimum 2 bar. If the pneumatic pipe is  long, pay attention to the hose cross-section (internal diameter min. 6 mm). Every pneumatic pipe must always have a maintenance unit. Ensure a constant pressure by using the pressure reducer.
Finally, insert the plug into the socket – make sure that the voltage specification of the device and the mains network is identical.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningNever operate the device without water, since the heating unit immediately heats up to 60°C or to the preheating temperature when the power switch is activated. If required,  the heating unit can be switched off via the display.

Setting the Correct Pressure

Before filling the tank, remove the accessories and set the correct polymerisation pressure. Proceed as follows (image, see 7.2):
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Temperatures higher than 100 °C: Working is only possible under pressure.
If no pressure is set, the heating switches off at 100 °C.
Hence working without pressure is only possible at temperatures below 100 °C.

  1. Activate main switch (green rocker switch).
  2. Close lid.
  3. Touch the Pressure key 5 (image, see 7.2). (3 bar default).
  4. If the pressure is very less (min. 2 bar), increase the pressure (max.4 bar at 20°C) using the black regulator on the back side. Release the regulator by pulling to do the setting  and press it in once again.
  5. If the pressure is too high, switch off the pressure 5 (image, see 7.2) and release the pressure. Turn the pressure regulator on the back side in the “minus” direction several  times; then, apply pressure to the tank. You can set the desired pressure by turning the regulator in the “plus” direction (Pressure regulator at 20 °C: max. 4 bar)

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2For safety reasons, the pressure setting is limited to max. 4 bar (at 20 ° C).
Attention: When working above 100°C, the pressure can increase by approx. 2 bar.
Note: Hence the unit should be filled only with water and should be pre-heated to the desired working temperature, before the actual work process.
To do this, select the preheating temperature and pressure accordingly.

Start-up

Define the unit’s main parameters before switching it on. These settings are performed in the Set-Up Menu 3. Familiarise yourself with the system’s various options before starting the polymerisation process. This particularly applies to functions 7 and 14.
(Please see „setup menu page 1“ on page 10 of this manual).
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Preheating temperatures above 100 °C are not stored. When restarting, the preheating temperature is 60 °C.

The Start menu in Polymerisation mode

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 1*Inverted (background is black) = ON

The Start menu in Compactor mode (without heater)

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 2

Setup menu page 1
In the Setup menu the following settings can be made:

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 3

Setup menu page 2

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 4

Description of features 5 – 14

Pressure ON/OFF
Bevore starting the programme you have to choose the pressure.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Temperatures higher than 100 °C: Working is only possible under pressure.
If no pressure is set, the heating switches off at 100 °C.
Hence working without pressure is only possible at temperatures below 100 °C.

Programme parameter und Polymerisation
Defines the parameters for the programme temperature and time.
You can store 13 programmes counter (1-13).
In every counter up to three polymerisation stages 1-3 can be mapped.
Touch the numbers to change the values.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 5

Polymerisation level 1 (Programme 1):

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 6

Examples of level 2 and level 3 :

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 7

Touch the arrow (Start) to start the process of polymerisation.
Pause or cancel the programme by pressing the “Stop/Pause”symbol.
In programme 2-13 the practice is the same.

The PolymerisationWASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 8

Preheating temperature
Defines the target temperature once the main switch has been activated. The pre-heat temperature also applies to waiting times and rest periods. Default: 60°C
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2If the programme temperature selected is higher, the temperature reverts back to this value when the programme ends.WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 9

After defining the desired working mode 14, it may make sense to adjust the pre-heat temperature of the programme temperature. This avoids long heat-up or cool-down phases.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Preheating temperatures above 100 °C are not stored. When restarting, the preheating temperature is 60 °C.

Clock timer
This defines the weekday activation and deactivation times.WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 10

Programmes running currently have a higher priority; they are not switched off until complete.

Sleep button displayWASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 11

When you press the Sleep button, the device goes into the Sleep mode (all functions except the Timer function are switched off). The device gets actuated when you press the touch display or with the timer and heats up or cools down to the preset pre-heating temperature.

Heater ON/OFF
Choosing the pressurepolymerisation mode (pressure and temperature) or Compactor mode (pressure without heater).

Selection of the temperature unit (Fahrenheit or Celsius)WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 12Pictograms for the time and date function cycle.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 13

Selection of the working mode
Defines whether the polymerisation process should start immediately or only after the heating value has been reached.WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 14

(a) (Default) The device heats to the temperature programmed under 6. After reaching this value, the result measured is validated by a control cycle. If the value is confirmed, the wax polymerisation process will start.
(b) The programmed polymerization begins immediately.

Information
Here the parameters of the touch screen, sensors, hardware and software are displayed.

Operation

General Operating Instructions
All instructions for using the unit, whether in verbal or written form, are based on our own experience and experimentation and can only be regarded as guidelines.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningPlease put on heat-resistant gloves
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2During longer periods of non-use please disconnect the power plug.

Operation
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Prevent locking problems:
The sliding parts of the lid/ container (bayonet lock) must be greased with Vasiline if the lid is difficult to move.
The O-ring has to be used with special lubricant Super O-Lube or similar.

  • Open the lid.
  • First set the workpieces, then fill the water till all the polymerisation parts are covered (max. up to the engraving = Marking in the tank) and close the lid up to the stop.
  • Switch on the main switch, the device will automatically heat up to 60°C or up to the value selected as the pre-heating temperature. If warning A appears, close the lid.
  • Activate the pressure 5.
  • The process of polymerisation starts when you touch the symbol 6. After the process of polymerisation has ended, the temperature falls/rises to the preset temperature  again.
    WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 15

Troubleshooting

Fault Cause Solution
Polyquick 260- heat T105 does not Lid is open (Fig. 1) Close lid against safety contact.
Temperatur-programme- parameter is to low Adapt the parameters.
Preheating temperature is to low Adapt the parameters.
Heater faulty Please contact our service department.
Pressure does not increase in chamber Lid seal 0-ring faulty Check 0-ring and replace if necessary.
Pressure regulator set to 0 (pressure gauge). Check pressure and adjust if necessary.
Lid not fully closed Close lid against safety contact or contact faulty.
Temperature monitor off or faulty Press in safety knob (left side of unit) and/or replace knob. Please contact our service department.
Display blank Temperature monitor off or faulty Press in safety knob (left side of unit) and/or replace knob. Please contact our service department.
Touchscreen malfunction Calibrate the touch display Switch on the unit. While the logo of
Wassermann appears please contact the touch display two times.
Then you will reach the self-explanatory touch panel-calibration*
(Page 17, Fig. 2-3).
Touchscreen under pressure Please contact our service department.
Screen protector damaged? Please contact our service department.
Unit does nothing Blown fuse Check the two fuses seperately.
Disconnect the power plug before replacing blown fuse at the rear of unit. Item no. 582013
Fuse 6,3 AM/250 V D 5 x 20

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2If the above recommendations do not solve the problem, contact your dental depot or our service department.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - figure 16

* VIDEO: CALIBRATION

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - qrhttps://t1p.de/TDRec

Care and Maintenance

Cleaning
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningDisconnect the power plug before starting any maintenance work.
The identification plate has always to be kept in easily legible condition and has not to be removed.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Remove external dirt from time to time with some form of cold cleaner.
Use only cold cleaners to avoid damaging the paintwork or removing the lettering.

Maintenance
At regular intervals, check the cover gasket (item no. 380063) for damages; for this purpose, remove the gasket ring (reddish brown silicon ring) from the ring groove of the pressure tank using a pair of blunt tweezers. The ring groove for holding the gasket ring must always be kept clean.
The O-ring must be used with special lubricant Super O-Lube or similar.
The sliding parts of the lid/ container (bayonet lock) must be greased with Vasiline if the lid is difficult to move.
Check the functioning of the lid safety switch by opening and closing the lid multiple times; a soft click must be audible while closing or opening.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Change the sealing ring every 18 months.

Repairs
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - warningServicing or repairs to the unit has only to be carried out by qualified technicians.
Only original spare parts are to be used. Responsibility for the product is voided if unauthorised persons alter it or if inappropriate components are installed.

Spare Parts
If necessary please contact our service hotline phone.
Service Hotline 0049 (0)40 / 730 926 -20/ -24
Scope of Delivery/ Accessories

Included parts Item no.
Flask bracket support 170414
Compressed air hose, 2 m 320026
Discharge hose, 2 m 320031
Fuse 6,3 AM/250 V D 5 x 20, 2 pcs.
Accessories/ Spare parts Item no. 
Flask bracket support 170414
Compressed air hose per meter 320026
Discharge hose per meter 320031
On request: flask basket as special accessory
Fuse 6,3 AM/250 V D 5 x 20 582013

Warranty
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2The warranty period for our equipment is 12 months. If faults occur within the warranty period, contact your dental depot or get in touch directly with our service department.
Your equipment should only be operated in perfect condition. If faults occur which could harm operators or third parties, the unit should not be used until it has been fixed.
This warranty does not cover damage caused by improper use, external mechanical causes, transport damage or interference with the unit by unauthorized persons.

Technical Data

Polyquick 260-T105 Item no.: 170993
Voltage 220–240 V / 50/60 Hz
Power consumption 4.3 A
Output 1100 W
W x H x D 420 x 450 (open=490) x 510 (+20 for air socket) mm
Weight 41 kg
Compressed air connection min. 2 bar
Operating pressure max. 4 bar (limiting at 20°C)
Pressure chamber Ø 240 mm, depth 175 mm (usable depth 160 mm)

The noise level of the unit amounts to ≤ 70 dB (A).
Other voltages on request.
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 2Technical changes reserved.

Disposing of the Unit

The unit has to be disposed by an authorized recycling operation. The selected company
has to be informed of all possibly health-hazardous residues in the unit.

Information on Disposal for Countries within the EU
Haier HWO60S4LMB2 60cm Wall Oven - icon 11To conserve and protect the environment, prevent environmental pollution and improve the recycling of raw materials, the European Commission adopted a directive that  requires the manufacturer to accept the return of electrical and electronic units for proper disposal or recycling.
Within the European Union units with this symbol should not therefore be disposed of in unsorted domestic waste.
For more information regarding proper disposal please apply at your local authoritie.

EU Declaration of Conformity

in accordance with 2014/35/EU (Low Voltage Directive) and 2014/30/EU (Electromagnetic Compatibility Directive) and 2006/42/EC (Machinery Directive) and 2011/65/EU (RoHS Directive) and 2014/68/EU (Pressure Units Directive)

Manufacturer: WASSERMANN
Dental-Maschinen GmbH
Rudorffweg 15-17
21031 Hamburg
Germany
Model: Polyquick 260-T105
Applicable standards: DIN EN 61010-1
DIN EN 61000-6-3
DIN EN 61000-6-1
DIN 45635-1
DIN EN 60335-1
Product description: Polimerisation
Unit and Compactor for dental applications
Item no. 170993

Hiermit wird bestätigt, dass die oben bezeichnete Maschine den genannten EU-Richtlinien entspricht. Diese Erklärung wird ungültig, falls die Maschine ohne unsere  Zustimmung verändert wird.
This is to confirm that the above mentioned machine complies with the described EU guidelines. This declaration becomes invalid if the machine is modified without our approval.

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - signature

WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - qr 2https://www.wassermann.hamburg/

Wassermann Dental-Maschinen GmbH Rudorffweg 15-17 • 21031 Hamburg – Germany Phone: +49 (0)40 730 926-20/ -24
Fax: +49 (0)40 730 37 24 [email protected]www.wassermann.hamburg
WASSERMANN Polyquick 260 T105 Pressure Polymerisation Unit and Compactor - icon 3/WassermannDentalmaschinen

Documents / Resources

WASSERMANN Polyquick 260-T105 Pressure Polymerisation Unit and Compactor [pdf] User Manual
Polyquick 260-T105, Pressure Polymerisation Unit and Compactor

Leave a comment

Your email address will not be published.