Installation Guide for AMP models including: AHS-630X, AHS-630X InfusePro Thin Step Light, InfusePro Thin Step Light, Thin Step Light, Light

Installation Guide

InfusePro Thin Step Light Louvered (Integrated LED) | AMP Lighting

InfusePro Thin Step Light Open (Integrated LED) | AMP Lighting


File Info : application/pdf, 8 Pages, 317.01KB

PDF preview unavailable. Download the PDF instead.

is-ahs-630X-ver2
INSTALLATION & MAINTENANCE GUIDE
AMP® LOW VOLTAGE LANDSCAPE LIGHTING AMP® InfusePro Thin Step Light
ITEM: AHS-630X
1-813-978-3900 · Mon-Fri 9am-6pm (EST) - 1 -

INSTALLATION & MAINTENANCE GUIDE
AMP® InfusePro- AHS-630X
! IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION
This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches (152 mm).
! IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS LIGHTED LAMP IS HOT!
WARNING ­ To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp. 2. Lamp gets HOT quickly! Contact only switch/plug when turning on. 3. Do not touch the hot lens, guard or enclosure. 4. Keep lamp away from materials that may burn. 5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp. 6. Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
813.978.3900 · customersupport@amplighting.com · www.amplighting.com
2

PACKAGE CONTENTS
A. (1) Luminaire B. (2) Anchors

C. (2) Screws

PRODUCT DIMENSIONS

8.25"

3.25"

0.75" 3.25"

AHS-6301-4-B-BZ 8.25"

1.5" 3.25"

AHS-6302-4-B-BZ 8.25"

0.5" AHS-6303-4-B-BZ
813.978.3900 · customersupport@amplighting.com · www.amplighting.com 3

INSTALLATION & MAINTENANCE GUIDE
AMP® InfusePro- AHS-630X

1 INSTALL LUMINAIRE
NOTE: Must be mounted with the wire exit on the left.
ANCHOR
SCREW LUMINAIRE

Note: Anchors are required for concrete or brick walls. Hold the luminaire on the wall and mark two points for the anchors using the mounting holes as guides. Then drill the proper holes using the marks. Insert the anchors into the drilled holes.
Attach the luminaire onto the desired mounting surface and secure with the screws. Hand tighten until snug with a screwdriver. Last, caulk around fixture to ensure it is sealed from water.

2 WIRE CONNECTIONS

SUPPLY CABLES

WIRE CONNECTORS MAIN SUPPLY CABLES

PIGTAIL
Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.

813.978.3900 · customersupport@amplighting.com · www.amplighting.com 4

813.978.3900 · customersupport@amplighting.com · www.amplighting.com 5

INSTALLATION & MAINTENANCE GUIDE
AMP® InfusePro- AHS-630X
813.978.3900 · customersupport@amplighting.com · www.amplighting.com 6

813.978.3900 · customersupport@amplighting.com · www.amplighting.com 7

1-813-978-3900 · Mon-Fri 9am-6pm (EST)
Specifications and product details subject to change without notice. © Copyright 2023, AMP® Lighting, Lutz FL USA 33549 · All rights reserved.
customersupport@amplighting.com · amplighting.com



References

Adobe PDF Library 17.0 Adobe InDesign 19.4 (Macintosh)