1. Giới thiệu
This manual provides detailed instructions for the safe and proper installation and operation of your LEADZM TMW798 TV Wall Mount. This wall mount is designed to securely hold televisions ranging from 32 to 70 inches, with a maximum load capacity of 110 lbs (50 kg). Please read this manual thoroughly before installation and retain it for future reference.
Image 1.1: The LEADZM TMW798 TV Wall Mount, highlighting its compatibility for 32-70 inch TVs, VESA 600x400mm, and support for up to 110 lbs.
2. Thông tin an toàn
Improper installation or use of this product can result in serious injury or damage. Please observe the following safety guidelines:
- Hãy đảm bảo bề mặt lắp đặt có thể chịu được trọng lượng tổng cộng của giá đỡ và tivi một cách an toàn.
- Không vượt quá tải trọng tối đa là 110 lbs (50 kg).
- Luôn sử dụng các công cụ phù hợp và làm theo tất cả các bước lắp đặt một cách cẩn thận.
- Nếu bạn không chắc chắn về bất kỳ phần nào của quy trình lắp đặt, hãy tham khảo ý kiến của chuyên gia có trình độ.
- Không cho trẻ em và vật nuôi lại gần khu vực làm việc trong quá trình lắp đặt.
Khả năng tương thích của loại tường
This mount is designed for installation on:
- Wood stud walls
- Solid brick walls
- Solid concrete walls
CẢNH BÁO: Do not mount this product on drywall alone. Anchors are required for brick and concrete walls.
Image 2.1: Illustration of compatible wall types: wood stud, brick, and concrete. Mounting on drywall alone is not supported.
3. Nội dung gói hàng
Please verify that all components are present and undamaged before beginning installation. The package includes the TV wall mount and a standard hardware kit. Refer to the accessory information table below for a detailed list of included hardware.
Image 3.1: Detailed table listing all included hardware accessories, their sizes, and quantities.
Image 3.2: A comprehensive layout of all screws, washers, spacers, wall anchors, and the spirit level included in the mounting hardware kit.
4. Thông số kỹ thuật
The following table outlines the technical specifications for the LEADZM TMW798 TV Wall Mount:
| Đặc điểm kỹ thuật | Giá trị |
|---|---|
| Thương hiệu | LÃNH ĐẠO |
| Người mẫu | TMW798 |
| Kiểu | Treo tường |
| Supportable Display Size | 32-70 inch (81.82-177.8 cm) |
| Phạm vi nghiêng | 0-10° |
| Max VESA Mounting Pattern | 600 x 400mm |
| Distance Between TV and Wall | 25mm |
| Sức chứa tải | 110 pound (50 kg) |
| Vật liệu | Cold Rolled Plate (Alloy Steel) |
| Bề mặt | High Temperature Paint Piano (Black) |
Image 4.1: A diagram illustrating the dimensions and tilt range of the TV wall mount, including measurements for VESA compatibility and wall distance.
5. Thiết lập và Cài đặt
Follow these general steps for installing your TV wall mount. Always refer to the specific instructions provided with your hardware kit for detailed diagrams and safety warnings.
- Chuẩn bị tivi: Attach the vertical TV brackets to the back of your television using the appropriate screws, washers, and spacers from the hardware kit. Ensure the brackets are securely fastened and centered. The VESA mounting pattern on your TV should match the mount's compatibility (up to 600x400mm).
- Xác định vị trí lắp đặt: Determine the desired height and position for your TV on the wall. Use a stud finder to locate wood studs if mounting on a wood stud wall. For brick or concrete walls, mark the drilling points.
- Khoan lỗ dẫn hướng: Carefully drill pilot holes at the marked locations. The size of the drill bit will depend on the type of wall and the anchors/lag bolts being used.
- Gắn tấm ốp tường: Secure the main wall plate to the wall using the provided lag bolts and washers. Use the included spirit level to ensure the wall plate is perfectly horizontal before tightening all fasteners.
- Hang the TV: With assistance, carefully lift the television and hook the attached TV brackets onto the wall plate. Ensure the TV is securely seated on the wall plate.
- Bảo vệ TV: Use the security screws or locking mechanisms on the TV brackets to prevent the TV from accidentally disengaging from the wall plate.
Ghi chú: The included screw kit is standard and may not fit all TV models. If the provided screws do not fit your television, please purchase a compatible screw kit separately.
Hình 5.1: Góc nhìn từ trên cao view of the LEADZM TMW798 TV Wall Mount, showing the main wall plate and two vertical TV brackets, illustrating the primary components for setup.
6. Hoạt động
Điều chỉnh góc nghiêng
The LEADZM TMW798 TV Wall Mount features a tilt range of 0-10 degrees, allowing you to adjust the viewing angle of your television. To adjust the tilt, loosen the tilt adjustment knobs or bolts on the side of the TV brackets, set the desired angle, and then securely tighten them to lock the TV in place.
Image 6.1: An illustration demonstrating the 0-10 degree depression angle adjustment feature of the TV wall mount, allowing for optimal viewgóc nghiêng.
7. Bảo trì
The LEADZM TMW798 TV Wall Mount is constructed from high-quality cold rolled plate (alloy steel) with a high-temperature paint piano surface finish, designed for durability and resistance to rust and deformation. Regular maintenance is minimal:
- Periodically check all mounting screws and bolts to ensure they remain tight and secure.
- Lau sạch giá đỡ bằng vải mềm, khô. Tránh sử dụng chất tẩy rửa có tính mài mòn hoặc dung môi vì có thể làm hỏng lớp phủ.
- Ensure no excessive weight is placed on the mounted television beyond its specified load capacity.
Image 7.1: An image highlighting key features of the mount, including its cold rolled steel sheet construction and security screw lock.
KHAI THÁC. Xử lý sự cố
Nếu gặp sự cố trong quá trình cài đặt hoặc sử dụng, hãy xem xét những điều sau:
- Mount not level: Ensure the wall plate was installed using a spirit level. If not, carefully remove and re-install, ensuring it is perfectly horizontal.
- TV not fitting: Double-check your TV's VESA mounting pattern against the mount's specifications (Max VESA 600x400mm). Ensure you are using the correct screws and spacers for your TV model.
- Screws not fitting TV: The included screw kit is standard. If the provided screws do not match your TV's threading or length requirements, you may need to purchase a compatible screw kit separately from a hardware store.
- Núi có cảm giác không ổn định: Verify that all lag bolts securing the wall plate to the wall are fully tightened. Ensure the wall type is compatible and that appropriate anchors were used for brick/concrete. Confirm the TV's weight does not exceed the 110 lbs (50 kg) load capacity.
- Difficulty with tilt adjustment: Ensure the tilt adjustment knobs or bolts are sufficiently loosened before attempting to change the angle. Tighten them firmly once the desired angle is achieved.