Weiser SmartCode 10 Traditional Z-Wave Electronic Lock (Model 9GED18000-028) User Manual

Sản phẩm trênview

The Weiser SmartCode 10 Traditional with Z-Wave Electronics is a robust electronic deadbolt designed for residential security. It integrates seamlessly with Z-Wave compatible home automation systems, offering enhanced control and convenience. This lock features a durable metal housing and the innovative SmartKey re-key technology.

Các tính năng chính:

• Electronic keypad operation with backlit numbers for night visibility.
• Manual key override for traditional access.
• Z-Wave 500 technology for wireless communication with security and home automation systems.
• Compatible with Amazon Alexa via Samsung SmartThings and/or Wink.
• SmartKey re-key technology allows re-keying the lock in seconds.
• Customizable automatic door locking after 30 seconds for peace of mind.
• Supports up to 30 user access codes and 1 master code.
• ANSI/BHMA Grade 2 certified and UL certified with a 20-minute fire rating.
• Designed for easy installation on most standard residential doors with just a screwdriver.

Image: Weiser SmartCode 10 Traditional Z-Wave Electronic Lock, showcasing the exterior keypad and brass finish.

Thiết lập và cài đặt

The Weiser SmartCode 10 lock is designed for straightforward installation, typically requiring only a screwdriver. Follow these general steps for a successful setup:

1. Prepare Your Door

• Ensure your door is prepared for a standard deadbolt installation.
• Remove any existing deadbolt hardware.

2. Lắp chốt

• Insert the latch into the edge of the door. Ensure the latch bolt is facing the correct direction (beveled edge towards the door frame).
• Cố định chốt khóa bằng các vít được cung cấp.

3. Lắp ráp bên ngoài

• Feed the cable and spindle through the hole in the door.
• Position the exterior keypad assembly flush against the door.

4. Lắp đặt tấm gắn bên trong

• Gắn tấm đế lắp đặt bên trong vào cửa, căn chỉnh sao cho thẳng hàng với cụm lắp đặt bên ngoài.
• Secure it with screws, ensuring the cable is routed correctly and not pinched.

5. Connect the Cable and Install Interior Assembly

• Kết nối cáp từ cụm bên ngoài đến cụm bên trong.
• Attach the interior assembly to the mounting plate, ensuring the spindle engages with the turnpiece.
• Secure the interior assembly with screws.

6. Lắp pin

• The lock requires 4 AA batteries (purchased separately).
• Open the battery cover on the interior assembly and insert the batteries, observing polarity.
• Đóng nắp pin.

7. Program User Codes

• Refer to the detailed programming instructions included with your lock to set your master code and individual user access codes.

8. SmartKey Re-keying (Optional)

• If you wish to re-key your lock to an existing Weiser key, use the SmartKey re-key tool and follow the instructions provided. This process takes seconds and requires three easy steps.

Operating Your SmartCode 10 Lock

Khóa cửa

• Từ bên ngoài: Press the "Lock" button on the keypad once. The deadbolt will extend automatically.
• Từ nội thất: Turn the interior turnpiece to the vertical (locked) position.
• Khóa tự động: The lock can be configured to automatically lock after 30 seconds of inactivity, providing added security.

Mở khóa cửa

• Sử dụng Mã Người dùng: Enter your valid 4-8 digit user code on the keypad. The deadbolt will retract.
• Sử dụng khóa: Insert the physical key into the keyhole and turn it to unlock the deadbolt.
• Tích hợp Z-Wave: If connected to a compatible Z-Wave system (e.g., Samsung SmartThings, Wink), you can lock/unlock the door remotely via your smartphone or smart home interface.

Kết nối Z-Wave

The SmartCode 10 lock features Z-Wave technology, allowing it to communicate wirelessly with your home automation system. This enables remote control, status monitoring, and integration with other smart devices. Consult your Z-Wave hub's instructions for pairing the lock with your system.

BẢO TRÌ

Thay thế pin

• The lock will provide a low battery warning (e.g., flashing light, audible beep).
• To replace batteries, remove the interior cover.
• Replace the 4 AA batteries with new alkaline batteries, ensuring correct polarity.
• Reattach the interior cover.

Vệ sinh

• Lau sạch bề mặt bên ngoài của ổ khóa bằng một vật mềm, sạch sẽ.amp Lau sạch bằng vải. Tránh sử dụng các chất tẩy rửa có tính ăn mòn hoặc dung môi có thể làm hỏng lớp phủ hoặc bàn phím.

Xử lý sự cố

• Khóa không phản hồi: Check battery levels and replace if necessary. Ensure the interior assembly is properly seated.
• Incorrect Code Entry: If the lock flashes red or beeps negatively after entering a code, re-enter the code carefully. Verify the code is active.
• Mechanism Lag: In rare instances, the locking mechanism may lag. Ensure the door is properly aligned and the strike plate is correctly installed. If issues persist, re-calibrate the lock or contact support.
• Các vấn đề về kết nối Z-Wave: Ensure your Z-Wave hub is powered on and within range. Re-attempt the pairing process if necessary.

Thông số kỹ thuật

Bảo hành và Hỗ trợ

Thông tin bảo hành

The Weiser SmartCode 10 Traditional Z-Wave Electronic Lock comes with a Lifetime Mechanical and Finish Warranty, ensuring the durability and appearance of your lock. Additionally, it includes a One-Year Electronics Warranty covering any electronic components.

For specific warranty claims or details, please refer to the warranty documentation included with your product or visit the official Weiser webđịa điểm.

Hỗ trợ khách hàng

If you encounter any issues or have questions regarding your Weiser SmartCode 10 lock, please consult the comprehensive user guide provided in the product packaging. For further assistance, you may contact Weiser customer support through their official webtrang web hoặc kênh hỗ trợ được chỉ định.