VEVOR C20250412-02 Fixed Rectangular Table Instruction Manual

Fixed Rectangular Table (Models C20250412-01 / C20250412-02)

This is the original instruction, please read all manual instructions care fully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

Specifications

Furniture Power Distribution Units (as listed):

• EU input: 220-240V~ 50/60Hz 10A; Output DC5V max. 2.1A
• USA input: 125V~ 60Hz 12A 1500W; Output DC5V max. 3A or DC5V max. 2A

Setup & Use (Concise)

1. Before assembly, read all manual instructions carefully and keep the manual available.
2. Verify all package components/accessories are present and labeled; keep them away from children.
3. Assemble only according to the provided assembly instructions; use ANSI-approved safety goggles and heavy-duty work gloves.
4. Assemble on a clean, soft underlay (e.g., carpet or cardboard) to avoid scratching the surface.
5. During installation, note that the product is not stable until fully installed—do not move it randomly.
6. Before use, check that the product is not abnormal; if abnormal, stop using it.

Safety and Compliance Information

⚠️ Warning – To reduce the risk of injury, user must read instructions manual carefully.

Correct Disposal for Furniture Power Distribution Units

This product is subject to the provision of European Directive 2012/19/EU. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.

FCC Information for Furniture Power Distribution Units

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment!

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This product may cause harmful interference.
2. This product must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this product not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.

Note: This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the product and receiver.
• Connect the product to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.

Product Parameters

* Products such as specifications, appearance, and design are subject to modification without prior notice.

Safety Instructions

Introduction

Thank you for purchasing our products. Committed to providing customers with the best quality products and service has always been our lifelong goal. Before using the product, please read this instruction manual carefully to ensure correct use. Keep the instruction manual in a place where the user can find it at any time.

Assembly Precautions

There are many components and accessories in the package. Each component and accessory is labeled with a letter or a number, check carefully before using any of them. Keep them away from children to prevent accidents.

1. Assemble only according to these instructions. Improper assembly may create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble if tired or when under the influence of alcohol, drugs or medication.
6. The product capabilities apply to properly and completely assembled products only.
7. Please install the product on a clean and soft underlay (such as carpet or cardboard) to avoid scratching or damaging the surface of the product.
8. If possible, you can use power tools to make assembly easier.
9. The main components of the product are relatively heavy. Please pay attention to safety during installation.
10. The product is not stable during installation. Please do not move it randomly before it is completely installed.
11. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual.
12. Unwrap and separate all parts in a clean work area.

*PLEASE BE SURE TO FOLLOW THE INSTALLATION STEPS IN THE MANUAL TO AVOID UNNECESSARY LOSSES CAUSED BY IMPROPER INSTALLATION.

User Precautions

1. The product complies with relevant standards and regulations. Installation of this device must comply with all applicable regulations, and it should only be operated in well-ventilated areas. Please read the user manual before installing and using this equipment.
2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
3. This product is not a toy. Do not allow children to play with or near this item.
4. This appliance is intended to be used in household and similar applications such as: Bedroom, hotel, homestay, guest room, office, etc.
5. Please use the product according to the intended use, warn of potential injury from misuse.
6. Please properly keep product. Check whether the product is abnormal before use. If it is abnormal, please stop using it.
7. This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
8. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

WARNING for Furniture Power Distrbution Units:

For type Y attachment:

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• For indoor use only.
• Do not use the Furniture Power Distribution Units in circumstances where the output polarity does not match the load polarity.
• Under no circumstances could the cover be opened. If the cover is damaged, the adapter may no longer be used.
• Disconnect the supply before making or breaking the connections.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
  SAVE THIS MANUAL

Part List

Assembly Step

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Step 11

Step 12

Step 13

This light strip is installed under the countertop.

Product Paramaters

* Products such as specifications, appearance, and design are subject to modification without prior notice.

Troubleshooting

• Interference with radio/TV reception: If the product causes harmful interference (detectable by turning the product off and on), try reorienting or relocating the receiving antenna, increasing the distance between the product and receiver, connecting the product to a different circuit outlet than the receiver, or consulting a dealer/experienced radio/TV technician.
• Damaged supply cord: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
• Adapter/cover issue: The cover must not be opened. If the cover is damaged, the adapter may no longer be used.