Verkada WH32 VLink Wireless Hub Installation Guide

© Copyright 2024 Verkada Inc. All rights reserved. Verkada and the Verkada logo are registered trademarks or service marks of Verkada Inc. (“Verkada”). All other trademarks are the property of their respective owners. Verkada may make changes to this document at any time without notice. The information presented herein may be inaccurate or outdated, and Verkada is under no obligation to maintain it. ALL INFORMATION IS PROVIDED “AS-IS” AND WITHOUT ANY WARRANTIES, IMPLIED, EXPRESS, OR OTHERWISE. VERKADA DISCLAIMS LIABILITY FOR ALL DAMAGES, INCLUDING WITHOUT LIMITATION ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES, ARISING OUT OF USE OF THIS DOCUMENT. Any intellectual property rights relating to Verkada products are and shall remain Verkada’s exclusive property. Use of any Verkada product is subject to Verkada’s end user agreement or other executed agreement with Verkada. No license, either expressed or implied, to use or distribute any Verkada product is granted under this document. This document may not be sold, resold, licensed or sublicensed and may not be transferred without Verkada’s prior written consent. No part of this document may be reproduced in whole or in part without the express written consent of Verkada.

Introduction

What’s in the box

What you’ll need

#2 Phillips driver (screwdriver or power drill)
7/32 inch (5.5mm) drill bit if using wall anchors

Placement

[EDIT] Place the product on a wall, etc.

Connect

For easy registration and setup, scan the QR code on the product. If you prefer to manually register your product, please proceed to:
verkada.com/start

Overview

LED Behaviors

Solid Orange
The Hub is on and booting up.
Flashing Orange
The Hub is updating firmware.
Solid Blue
The Hub is running and online.
Flashing Blue
The Hub is running and offline.

Mount Plate Overview

Mount plate details [EDIT]

A Wall/ Ceiling/Square Junction Box (4 inches / 101.6 mm)
B Single Gang Junction Box
C Double Gang Junction Box
D Round Junction Box (4 inches / 101.6 mm) and ( 3½ inches / 88.9 mm)
E European Junction Box

Technical Specifications

Preparation

Remove top cover
Remove mount plate

Mounting

Fasten the Mount Plate using the necessary mounting screw holes. Cut a hole into the wall if planning on routing the cables via the wall.
Route the necessary cabling through the holes in the wall and Mount Plate. Strip the necessary wires.
Pull the cables through the opening in the middle of the device.
Align the device on top of the Mount Plate and slide down to secure it.
Using the TO security torx driver, fasten down the security screw in the middle of the device
Connect the cable ends to the terminal blocks and push the excess back into the wall
Once the terminal block connections are made, turn the switch to the ON position.
Toe in the Top Cover by hooking over the device.
Fasten the security screw on the bottom of the device
Fasten the Mount Plate using the necessary mounting screw holes. Cut a hole into the wall if planning on routing the cables via the wall.
Align the device on top of the Mount Plate and slide down to secure.
Using the T10 security torx driver, fasten down the security screw in the middle of the device
Push the cables through the top opening on the device and pull the ends through the middle cutout
Connect the cable ends to the terminal blocks and pull the excess from the top
Remove the small plastic door on the top of the cover.
Once the terminal block connections are made, turn the switch to the ON position.
Toe in the Top Cover by hooking over the device.
Fasten the security screw on the bottom of the device
Fasten the Mount Plate using the necessary mounting screw holes. Cut a hole into the wall if planning on routing the cables via the wall.
Align the device on top of the Mount Plate and slide down to secure.
Using the 110 security torx driver, fasten down the security screw in the middle of the device
Push the cables through the bottom opening on the device and pull the ends through the middle cutout
Connect the cable ends to the terminal blocks and pull the excess from the top.
Remove the small plastic door on the bottom of the cover

Once the terminal block connections are made, turn the switch to the ON position.
Toe in the Top Cover by hooking over the device.
Fasten the security screw on the bottom of the device

Appendix

Compliance

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT NOTE :

FCC Radiation Exposure Statement :

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

IC Statement

This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

Support

Thank you for purchasing this Verkada product. If for any reason you’re experiencing issues or need assistance, please contact our 24/7 Technical Support Team immediately.

Sincerely,