Veise RZ-A Keypad Digital Deadbolt Installation Guide

What should I do if any parts are missing or
damaged?
If any parts are missing or damaged, please contact Customer
Support for assistance.
Can I use an electric screwdriver during
installation?
No, it is advised not to use an electric screwdriver during
installation to avoid any damage.
When should I load batteries into the
lock?
Only load batteries into the lock once it is completely installed
to ensure proper functioning.

“`

View Fullscreen

RZ-A
Keypad Digital Deadbolt
Installation Guide / Programming Instructions
Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.

Installation Overview

Programming Instructions

P 3

STEP 1: Prepare the door and check dimensions

P 4

STEP 2: Install the latch and strike

P 6

STEP 3: Install exterior assembly

P 7

STEP 4: Install interior assembly

P 8

STEP 5: Detect left/right hand door installation

P 9

At a Glance

P 15 Factory Default Settings

P10 How to Use

P16 Troubleshooting

P 11 Definitions

P17 Information & Safety Warnings

P 12 Code Format

P 13 Quick Set Up

TOOL REQUIRED:
Do not use an electric screwdriver during installation.

IMPORTANT:
Do not load batteries until lock is completely installed.

INSTALLATION OVERVIEW
Mounting plate (E)

Interior Assembly (F)

Battery Cover (G)

Exterior Assembly (D)
Backup key (M) 1

Latch (A)

Mounting plate Screws (J)

Interior Assembly Screws (K)

Latch Screws (I)

Strike (C)
Reinforcement plate (C-1)

Strike Screws (H)

Parts List
A Latch x1

B Drive-In Collar (Optional) C Strike x1

E Mounting Plate x1

F Interior Assembly x1

C-1 Reinforcement
Plate x1 (optional)
G Battery Cover x1

J Mounting plate
Screws x2

K Interior Assembly
Screws x3

L Reset Tool x1

D Exterior Assembly x1
H Strike Screws x2 I Latch Screws x2 M Backup Key x2

If any parts are missing or damaged, please contact Customer Support. 2

STEP
1 Prepare the door and check dimensions

A
Measure to confirm that the hole in the door is 2-1/8″ (54mm).
Measure to confirm that the hole in the door edge is 1″ (25mm).

B
Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)

2-3/8″ or 2-3/4″ (60 or 70mm)

C
Measure to confirm that the door is 1-3/8″ to 2″ (35 mm or 50mm) thick.

1-3/8″ to 2″ (35mm or 50mm)

D
Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.

1″ 25mm

STEP
2 Install the latch and strike
A Determine backset and adjust the latch

YES
No adjustment is required. Proceed to next step.

Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?

B
Install the latch

chiseled

NO
Slotted hole is NOT centered.

Rotate and pull the

latch as shown to extend latch.

(602m-3m/8)”

pull

up
Latch Screws (*)

not chiseled

Drive-In Collar (B)

(702m-3m/4)” 4

C Use a screwdriver to test if
deadbolt works smoothly.

D Install strike on the door frame.

IMPORTANT:
Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.

(Optional)

STEP
3 Install exterior assembly
IMPORTANT:
Before installation, make sure the latch is fully retracted (in the unlocked position)

Unlocked

Locked

Tourque blade

With the latch fully retracted (in the unlocked position), route the cable below the latch, and

insert the tourque blade through the slot in the

latch.

Keep parallel to door edge.

Mounting plate Screws(J)

Secure the mounting plate with the supplied screws. Do not overtighten

screws.

STEP
4 Install interior assembly
A
Push the battery cover out in the direction as illustrated.
IMPORTANT:
Do not load batteries until lock is completely installed.
C Keep the thumb turn in vertical position and install the interior assembly.
Horizontal

Insert the cable connector to the

socket. Push the

connector in firmly

until it is completely

attached.

Attach Interior Assembly to

Mounting Plate and

tighten 3 Screws.

Unlocked 7

Interior Assembly Screws (K)

STEP
5 Detect left/right hand door installation Reset the lock to teach the lock the orientation of the door.

IMPORTANT:

This step is required and crucial for the lock to operate properly.

While the door is OPEN and UNLOCKED, load 3 AA batteries

into the battery compartment.

Note:

For long last, please use all new, non-rechargeable Alkaline batteries only.

Press and hold the Reset button on the interior assembly by using the

reset tool.

Load the 4th battery and keep holding the reset button for 3 seconds, until

you hear the sound of “beep”. The

latch bolt will extend to learn the

orientation of the door automatically.

Unlocked

Reset button

PROGRAMMING INSTRUCTIONS

At a Glance

Exterior Assembly

Interior Assembly

Multi-Function Button(MFB) Keypad
Keyhole
9

Battery Cover Reset Button Thumb Turn

How to Use

UNLOCK the door from outside

Master code +

or User code +

LOCK the door from outside

Auto Lock Mode
In Auto Lock mode, the bolt will extend out automatically in 30 seconds after unlocking.

Manual Mode
Press any key on keypad for 2 seconds.

UNLOCK the door from inside
Rotate the thumb turn to Unlock position.

LOCK the door from inside

Auto Lock Mode
In Auto Lock mode, the device will be locked automatically.

Manual Mode Rotate the thumb turn to Lock Position.

Definitions

Programming Basic

· Master Code Required for programming and feature settings. Master code can be used to unlock the door under vacation mode. The default master code needs to be changed before programming. Property owner & manager should keep this information confidential.
· Auto Lock Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can customize the Auto Lock time delay between 10 and 99 seconds.
· Key Unlock Key Unlock is always available when the batteries are completely dead or valid User Codes are forgotten.
· Low Battery Indicator If you hear 10 beeps along with 10 red light flashing after pressing any key to lock or unlock the door, that’s an alert for replacing batteries. Please replace with 4 brand new AA alkaline batteries and do not mix used and new batteries. All settings are stored in the lock while the batteries are removed and replaced.
· Wrong Entry Limit After 10 unsuccessful attempts at entering a invalid PIN code, the unit will shut down for 3 minutes.
11

· Silent Mode The beep sounds when pressing keypad can be muted. But you will still hear low battery and system alerts.
· Vacation Mode This is a security feature for you when you are leaving your home for vacation or long trip. Enabling vacation mode will restrict all user codes until master code is entered on keypad. If the lock would be unlocked by the thumb turn from the inside, the lock will sound an alarm.
· One Time User Code This code only can be used once and will be automatically deleted after used.
· Unlock with Fake code User can prevent pin code exposure from strangers by entering random digits before or after pin code.

Code Format

Programming Basic

1. Master Code(4 to 10 digits): The default Master Code is 12345678. It is required that you change it to a code of your own before
programming. 2. User Code (4 to 10 digits): A total of 20 User Codes (including one temporary one-time User Code) can be programmed and stored. 3. Both Master Code and User Code don’t support the following combination of numbers.
Forward number sequence Backward number sequence Repeat number sequence
Contain existing code sequence

Quick Set Up

The default Master Code is 12345678 .
IMPORTANT: It is required that you change it to a code of
your own before programming.

Change Master Code

+ Master Code + Wait for long green lights

Press Wait for green light flash

New Master Code + Wait for green light flash

New Master Code +
Succeed Green light flash

Add User Code

+ Master Code + Wait for long green lights

Press Wait for green light flash

New User Code + Wait for green light flash

New User Code +
Succeed Green light flash

Delete User Code

+ Master Code + Wait for long green lights

Press Wait for green light flash

Silent Mode
13

+ Master Code + Wait for long green lights

Press Wait for green light flash

Unwanted User Code +
Succeed Green light flash
Silent Mode Disabled Green light flash
Silent Mode Enabled Green light flash

+ Master Code +

Press

Auto

Lock

Wait for long green lights

Wait for green light flash

Auto Lock Enabled Green light flash
Auto Lock Disabled Green light flash

Set Auto Lock Time

+ Master Code + Wait for long green lights

Press Wait for green light flash

Enter New Duration Time + c10-99
Succeed Green light flash

Add One-Time Code

+ Master Code + Wait for long green lights

Press Wait for green light flash

New User Code + Wait for green light flash

New User Code +
Succeed Green light flash

Enable Vacation mode

+ Master Code + Wait for long green lights

Press Wait for green light flash

Press
Vacation Mode Enabled Green light flash

Disable Vacation mode

Master Code +
Vacation Mode Disabled The door was opened

Notes: 1. Beeps only sound when the Silent Mode is disabled. 2. If the indicators flash red light, it means your setting failed and it will require to re-enter master mode if you would like to continue your programming.
14

Factory Default Settings

How to Reset?

IMPORTANT:

The resetting will delete all User Codes stored in the lock.

Step 1. Keep the door open and unlocked.
Step 2. Press and hold the Reset button, at the same time take out one battery and then place it back.
Step 3. Keep holding the Reset button for 3 seconds, until you hear the sound of “beep” and the latch will extend automatically.

Settings Master Code
Auto Lock Silent Mode Wrong Code Entry Limit Shutdown Time Vacation Mode
15

Reset button
Factory Defaut 12345678 Disabled Disabled 10 times 3 mins Disabled

Troubleshooting
Why does not the latch extend but the motor is rotating when resetting my lock? Improper installation may have caused the issue. Please follow the steps to review:
1. Please make sure the latch and strike are aligned. 2. Please slightly loosen the mounting screws on the external
assembly keypad and the latch bolt if the screws are over-tightened. 3. Please open your door and reset the lock.
Why does not the latch extend and the motor isn’t rotating when resetting my lock? The deadbolt latch should be retracted(unlocked) through all your installation process. The thumb turn should be vertical in your installation steps 4C and 5A. Please open your door and reset the lock.
When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times? It happens when the latch and strike are misaligned. Please make sure the bolt hole on the door frame is at least 1 inch deep, so that the bolt can be fully extended. Please check if the door can be closed properly, the deadbolt should not impact the strike or door frame on the door frame side, it should go directly into the hole properly.

Why does my lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position? You may need to re-install the whole lock. Please make sure when you start to install, the lock is in unlocked status; Please make sure the thumb turn is vertical. Please do not put the backup key in the lock. What does 5 short and fast beeps mean while programming? It alerts you either time-out or wrong entry. Please be sure to complete each setting step within 5 seconds. Please change the default master code in the first time programming. Please be sure the user code is with correct format and with 4 to 10 digits. What if I forget my Master Codes? If you forget your Master code, resetting your lock, then the original master code (12345678) works, and all previous user codes were erased.
16

Information & Safety Warnings
· Protect your User Codes and Master Code. · Restrict access to your lock’s interior assembly and routinely check your
settings to ensure they have not been altered without your knowledge. · Do not use an electric screwdriver during installation. · This manufacturer advises that no lock can provide complete security by
itself. · This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. · No lock can substitute for caution, awareness of your environment, and
common sense.

· Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
· The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
· Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.

Documents / Resources

Veise RZ-A Keypad Digital Deadbolt [pdf] Installation Guide
RZ-A, Veise, Veise, Veise, Keyless, Entry, Door, Lock, Electronic, Keypad, Deadbolt, Keyed, Entry, Auto, Lock, Anti-Peeking, Password, Back, Lit, Easy, Installation, Design, Matte, Black, B0BMQWRBRW, B0BL9FHWQH, B09YLQV98H, B09YLNY2DD

References

User Manual

Veise RZ-A Keypad Digital Deadbolt Installation Guide

RZ-A Keypad Digital Deadbolt

Product Information

Specifications:

Product Usage Instructions

Installation Overview:

Step 1: Prepare the door and check dimensions

Step 2: Install the latch and strike

Step 3: Install exterior assembly

Step 4: Install interior assembly

FAQ

Frequently Asked Questions:

Documents / Resources

References

Leave a comment

Cancel reply