Categories: udiR C

udiR C U32 Inverted Flight Quadcopter Instruction Manual

 

 

INSTRUCTION MANUAL

U32

For technical support, contact us at support@usatoyz.com

DRONE AND TRANSMITTER OVERVIEW

1. Drone

Top View:                           Bottom View:

   

  1. Blade
  2. Battery
  3. Motor
  4. Blade Guard
  5. Drone Body
  6. Body Lights
  7. Power Indicator Light
2. Transmitter

  1. Power Indicator Light
  2. Forward/Backward/Left/Right Stick
  3. Left/Right Trim
  4. Forward/Backward Trim
  5. Rudder Trim
  6. Throttle/Rudder Stick
  7. Power Switch
  8. 180° Left Flip Button
  9. 180° Right Flip Button
  10. Headless Mode Button
    (Press Down)
  11. High/Medium/Low Speed Mode Button
    (Press Down)
  12. Return Home Button
  13. 360° Flip Button

Direction of Power Switch Indicator Direction of Trim Indicator

IMPORTANT NOTICE

Important Statement:

(1) This product is not a toy but a piece of complicated equipment which is integrated with professional knowledge by mechanic electronic, air mechanics, high-frequency emission etc. It should be installed and adjusted correctly to avoid accidents. The user must always operate in a sale manner. We undertake no liability for human injury or property damage caused by improper operation, as we have no control over setup, use and operation of this drone.
(2)This drone is suitable for experienced RC drone users aged 14 years or above.
No safe for users under the age of 14 to use.
(3) The flying field must be legally approved by your local government.
(4) UDIRC has entrusted the distributor to provide technical support and alter-sale service. If you have any questions about use, operation repair etc., please contact USA Toyz at support@usatoyz.com

Safely Precautions:
Improper assembly, broken main frame, defective electronic equipment, or unskilled operation may cause unpredictable accidents such as drone damage or human injury. Please pay special attention to the following safety procedures:

( 1 ) Keep away from obstacles and crowds
The speed and status of a flying RC drone is uncertain and may cause potential danger. The user must keep away from crowds, tall buildings, power lines etc. when operating a flying RC drone. Do not fly a RC drone in wet or storm/thunder conditions.
(2) Keep away from humid environment
The drone is made of precise electronic components. Humidity or water vapor may damage electronic components causing accidents.
(3) Sale operation
Please operate the RC drone in accordance with your flying skills. User fatigue, and improper operation may increase the rate of accidents.
(4) Keep away from rotating parts
Rotating parts can cause serious injury and damage, Keep face and body away from rotating motors.
(5) Keep away from heat
The RC drone is made of metal, fiber, plastic, electronic components etc. Keep away from heat and direct sunshine to avoid distortion and damage,
(6) If you’re about to crash into something, turn the throttle down to zero.

IMPORTANT PRE-FLIGHT INSTRUCTIONS

Checklist Before Flight:
(1) Flying area must be spacious. We suggest at least 26Ft (length)*8M (width)*5M (height) of flying space.
(2) Make sure the battery of the drone and the transmitter are fully charged.
(3) Make sure the Throttle Stick of the transmitter is in the lowest position.
(4) Make sure your transmitter and drone are calibrated.

TRANSMITTER SETUP

Battery Installation: Open the battery cover at the back of the transmitter and install 4 AAA batteries (not included) in accordance with electrode instructions.

  1. 4xAAA (1.5V) Alkaline Batteries
  2. Battery Cover

CAUTION:

  1. Make sure the batteries are installed correctly by matching the electrodes.
  2. Do not mix new and old batteries
  3. Do not mix different kinds of batteries.

CHARGING INSTRUCTIONS

  1. Connect the USB charging cable to any available USB port, then connect the drone battery to the USB charging cable.
  2. After connecting the USB charging cable to the USB port, the USB indicator light will turn green. After connecting the USB charging cable to the drone battery, the USB indicator light will turn red.
  3. When fully charged, the light will switch to a solid green.
  4. Average charging time: 50 minutes

NOTE:
* To avoid damage and explosions, never place the batteries on a high temperature surface or close to fires or heating devices.
* Never use the batteries for any purpose other than with the drone.
* Never place batteries in water. Keep in a dry place only.
* Never attempt to open the batteries
* Never leave the batteries unsupervised during charging.

Charging Methods

                             

Phone Charger    USB      Power Bank      Computer   Car Charger

NOTE: For faster charging, it is recommended to use a 5V 2A AC Adapter (not enclosed) to charge the battery.

 

LiPo Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be thrown out with your household trash. Please contact your local environmental waste agency or your nearest LiPo battery recycling center.

FREQUENCY PAIRING INSTRUCTIONS

  1. Turn on the transmitter switch, It’s indicator lights will begin to quickly flash.
  2. Push the Throttle Stick all the way up then all the way down. The indicator lights will slowly flash indicating the transmitter has entered code pairing.
  3. Turn on the drone.
  4. Place the drone on a flat surface. The indicator lights of the drone will switch from flashing to a solid light, indicating successful frequency pairing. The drone is now ready to be controlled.

CALIBRATION INSTRUCTIONS

To ensure control of your drone, it is important to always calibrate your drone with your transmitter before flying. Re-calibrating is necessary in the case of difficult operation after take off.

1. Turn off the drone switch and then turn off the transmitter power switch.
2. Turn on the transmitter switch, push the Throttle Stick all the way up, then all the way down, and the transmitter enters pairing mode.
3. Power on the drone and place it on a flat surface in a horizontal position. The back of the drone should face the user and the front of the drone should face forward. You will hear a “di, do, di” beeping noise three seconds later, which indicates successful code pairing. The drone light will turn solid.

4. Do not move the Throttle Stick before successful calibration. Push the Forward/Backward/Left/Right Stick as shown below {Picture 1). The drone light will flash, which indicates that the drone is calibrating When the drone light remains solid, turn over the drone and put it on a flat surface, repeat the operation to push the Forward/Backward/Left/Right Stick as shown below (Picture 2). The drone lights will flash, indicating that the drone is calibrating. When the drone lights remain solid, your drone is ready to fly!

Picture 1


Picture 2

MOTOR INFORMATION

  1. Power on the drone and check the direction of the rotating blades.
  2. The left front and right rear blades rotate clockwise while the right front and left rear blades rotate counterclockwise.
    TIPS:
    – The power indicator light is on the drone rear.
    – Press the relative transmitter Trim button to adjust the rudder if the drone tilts to one side when flying.

  1. A Blade Clockwise
  2. B Blade Counterclockwise

TAKE OFF INSTRUCTIONS

To get your drone in the air, the only control you need is the Throttle Stick.

  1. Push the Throttle Stick (left stick) up very slowly, just to get the propellers going. Then stop.
  2. To get comfortable with the Throttle Stick’s sensitivity, repeat the first step a couple of times.
  3. Slowly push the throttle Stick up further than before until the drone lifts up. Pull the throttle back down to zero to land the drone.

FLIGHT CONTROLS

1. Push the Throttle Stick up to fly the drone up, and pull the Stick down to fly the drone down.

2. Move the Forward/Backward/Left/Right Stick to the left to fly the drone to the left, and move the Stick to the right to fly the drone to the right.

3. Push the Forward/Backward/Left/Right Stick up to fly the drone forward, and pull the Stick down to fly the drone backwards.

4. Move the Throttle Stick to the left to rotate the drone to the left, and move the Stick to the right to rotate the drone to the right.

5. If the drone tilts forward or backward:


Press the Backward Trim to balance if the drone drifts forward, and press the Forward Trim if the drone drifts backward.

 

6. If the drone tilts to the left or right:


Press the Right Trim to balance if the drone drifts to the left, and press the Left Trim to balance if the drone drifts to the right.

 

7. If the drone rotates to the left or right:


Press the Right Rotation Trim to balance if the drone rotates to the left, and press the Left Rotation Trim to balance if the the drone rotates to the right.

 

SPEED MODES

By default, the drone is in Medium Speed Mode (M). To enter High Speed Mode (H), press the Throttle Stick once. The transmitter will issue a “dididi” sound, which indicates that the drone has entered High Speed Mode (H); Press the Throttle Stick again and the transmitter will a issue a “di”, which indicates that the drone has entered Low Speed Mode (L); Press the Throttle Stick one more time and the transmitter will issue a “didi” sound, which indicates that the drone has entered Medium Speed Mode (M).

High/Medium/Low Speed Mode Button

STUNTS

180° Flips

When the drone is flying, press the left button on the top of the transmitter, the transmitter will issue a “di” sound and the drone will do a 180° flip to the left. Press the right button on the top of the transmitter, the transmitter will issue a “di” sound and the drone will do 180° flip to the right.

  1. Left 180 ° Flip Button
  2. Right 180 ° Flip Button
360° Flips

Press the 360° Flip button when the drone is flying, and the transmitter will issue a “dididi” sound. Push the Forward/Backward/Left/Right Stick any direction and the drone will do 360° flips in the same direction accordingly.

  1. 360°Flip Button

HEADLESS MODE

Drones generally have a front and rear indicated by LED lights or colored blades. Before take off, users are instructed to position the head of the drone away from the user. Under headless mode, the users can operate the drone without worrying about the orientation.
Headless mode is designed for beginners and users who fly the drone in the daylight or at a far distance.
When the drone in Headless Mode, push the Right Stick to forward/backward/left/right, and the drone will fly to forward/backward/left/right accordingly.

Prerequisite: Position the drone in such a way that its front is your front (see Picture 1).
Tip: Do not change the orientation of the transmitter (see Picture 2) after entering headless mode.

To turn on Headless Mode: Press the Headless Mode button. The LED light of your drone will turn OFF signaling that the Headless Mode is ready.

To turn off Headless Mode: Press the Headless Mode button again. The LED light of your drone will turn OFF signaling that the Headless Mode is ready.

RETURN HOME FUNCTION

Bring your drone back home automatically by pressing and holding the Return Home Button

IMPORTANT:

* The return home function is only available when the drone is in headless mode.
* Make sure the drone is in front of the users (see Picture 1). Wrong position may cause the drone fly to other direction (see Picture 2).

REPLACING THE MOTORS

     

Picture 1  Remove the motor     Picture 2  Install the motor

  1. Pull out the red/white motor plug from the moter holder port. Force apart the motor buckle around the motor (see Picture 1) to take out the motor.
  2. Put the new motor back to the original position in the drone and install it into the motor buckle (see Picture 2). Then connect the motor plug with the motor holder port. (Red motor plug pairs with the red motor holder port, the white motor plug pairs with the white motor holder port)

Note: After installing the new motor, recheck the motor wire and make sure it’s not stuck in the motor holder.

BATTERY INSTALLATION

     

Picture 1  Remove the battery      Picture 2  Install the battery

  1. Push the battery buckle in accordance with the arrow indication in the buckle. Lift up to remove the battery (see Picture 1).
  2. Put the battery back to its original position and press it down (see Picture 2).

SPARE PARTS

(7)

(1)

(3)(5)

(8)

U32-01
Drone Case

U32-02
Blade Guard
U32-03
Blade

U32-04
Drone Frame

(2)

(4)

(6)

U32-05
Clockwise Motor
(Red Plug)

U32-06
Counterclockwise Motor (White Plug)
U32-07
Battery

U32-08
Transmitter

Exploded View

No.

Name No. Name No.

Name

1

Blade Guard

4

Counterclockwise Motor

7

Drone Housing

2

Clockwise Motor

5

B Blade

8

Drone Frame

3

A Blade

6

Battery Box

TROUBLESHOOTING GUIDE

No.

Problem Possible Cause

Solution

1

The transmitter indicator light is off 1. The transmitter battery is too low. 1. Replace the battery.
2. The battery’s positive pole and negative pole are in reverse order. 2. Install the battery in accordance with the user manual.
3. Poor connection. 3. Clean any dirt between the battery and drone connectors.

2

Failure to pair the drone with transmitter 1. Indicator light is off. 1. The same as above (1.2.3.)
2. There is interfering signal nearby. 2. Restart the drone and power on the transmitter.
3. Misoperation. 3. Operate the drone step by step in accordance with the user manual.
4. The electronic component is damaged. 4. Contact support@usatoyz.com for additional troubleshooting.

3

The drone is under-powered or cannot fly. 1. The blades are deformed / damaged. 1. Replace the blades.
2. Drone battery is low. 2. Recharge the drone battery.
3. Incorrect installation of blade. 3. Install the blade in accordance with user manual instruction.

4

The drone doesn’t hover and tilts to one side 1. The blades are deformed / damaged. 1. Replace the blades.
2. The motor holder may be deformed. 2. Replace the motor holder.
3. The gyro did not reset after a crash. 3. Put the drone on the flat ground for about 10s or restart the drone to calibrate again.
4. The motor is damaged. 4. Replace motor.

5

The drone indicator light is off 1. The drone battery is too low. 1. Recharge the drone battery.
2. The battery is expired or over charge protection. 2. Replace with a new battery.
3. Poor connection. 3. Disconnect the drone power connector then re-connect.

For technical support, contact support@usatoyz.com

To ensure that play is both safe and fun, please review these operating instructions with your children:

Failure to follow all safety instructions may result in injury or property damage none of which USA Toyz will be held liable for as proper warnings are outlined in the manual.

  • Upon use of this product the end user assumes all responsibility and USA Toyz cannot be held liable for any personal injury and/or property damage.
  • This item contains fast moving parts, motors and/or other wiring. When using it, basic precautions should always be followed including but not limited to the following:
  • Keep your eye on the product at all times
  • Tie back hair or wear a hat to avoid entanglement or injury
  • Keep hands, hair and loose clothing away from moving parts when the power switch is turned ON.
  • Please ensure the product is turned off when not in use.
CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE SELLER WILL VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Documents / Resources

udiR C U32 Inverted Flight Quadcopter [pdf] Instruction Manual
U32 Inverted Flight Quadcopter, U32, Inverted Flight Quadcopter

Recent Posts

Supersonic SC1321BL Portable Speaker

Supersonic SC1321BL Portable Speaker Specifications Product Dimensions: 4 x 4 x 8 inches Item Weight:…

2 mins ago

Inland 87078 3.5mm Earbuds Black-Instruction Manual

Inland 87078 3.5mm Earbuds Black Specification Brand INLAND Color Black Form Factor In Ear Connectivity…

5 mins ago

Supersonic SC1317RD Portable Speaker Instruction Guide

Supersonic SC1317RD Portable Speaker Specifications Connectivity Technology: Auxiliary, USB Mounting Type: Freestanding Impedance: 4 Ohm…

9 mins ago

id America IDH202-SIL Metropolitan Aluminum In-Ear Headphones User Manual

id America id America IDH202-SIL Metropolitan Aluminum In-Ear Headphones Specifications Product Dimensions: 0.47 x 0.66…

16 mins ago

Rockville WA658 6.5-inches In-Wall Home Speakers-Owner’s Manual

Rockville WA658 6.5-inches In-Wall Home Speakers Specifications Brand Rockville Model Name WA658 Speaker Type Monitor…

27 mins ago

Tunewear BT-MACARON-02 BOOMTUNE Rechargeable Speaker-User Manual

Tunewear BT-MACARON-02 BOOMTUNE Rechargeable Speaker Specification Speaker Type Computer Model Number BT-MACARON-02 Connectivity Technology USB…

43 mins ago