TWS True Wireless Bluetooth Earbuds
TWS-X10Plus Use Manual
(Please read this manual carefully when using this product)
USB charging cable
Bluetooth version: V5.0
Support protocol: A2DP/AVRCP/HFP/HSP
BT transmission: 10M
Talking time: 3 Hours
Playing time: 3 Hours
Earphone battery: 50mAh
Charging case battery: 1600mAh
Earphone charging time: 1 Hour
Case charging time: 1.5 Hours
Support system: All bluetooth device
Packing list: Earphone *l pair, Charging case*lpc, Ear-paci*3 pairs, Charging cable *l pc
- There are three types of ear-pads with small, middle and large size(As below picture A), please choose the suitable size as you need.
Mark “L” and “R” on the earbuds, please wear the “L” for left ear, “R” for right ear.
Attention: Maybe your left and right ear are suit for different size ear-pad, please wear into your ear and turn to suitable location(As picture B).
Power on: The earbuds will power on automatically when take out from the charging case. (If without the charging case or charging case have no power, long touch the earubds for 3 seconds to power on)
The two earbuds will power on and paired to stereo after taking out from charging case. The right earbud will flash red and blue light in turns, while left earbuds flash blue light slowly. Then turn on the mobile bluetooth to search and connect “TWS-X10Plus”
Power off(Three methods):
- The earbuds will be power off automatically after put into the charging case.
- The earbuds will be power off automatically after disconnect the bluetooth connection over 5 minutes.
- Long touch either of the earbuds over 5 seconds.
Music control: Double click the touch area for next track, single click for pause /play. click for pause /play.
Answer phone calls: Single click the touch area for answering, and click on the phone for hanging up.
Call-reject: Long touch either of the earphone for 2 seconds.
Redialing: Click eitherof the earphone by three times quickly.
Siri control: Click either of the earphone for 2 seconds to awake and close Siri (Only support IOS system).
Mobile charging: Connect the mobile and charging case USB output end with the charging cable
Single earbud operation: Take the left or right earbud, long
touch for 5 seconds to red and blue flash light in turns, turn on the mobile bluetooth to search and connect the “TWS-X10Plus”. Both of the two earbuds have call function.
Use the earbuds again: Take out the two earbuds from the charging case, they will be paired and connect the mobile bluetooth automatically. (The last connected bluetooth device)
Earbuds indicator lights instruction:
A: Flash blue light slowly, no connection
B: Flash blue light by one time each 5 seconds, connected
C: Flash Red light, low battery
D: Flash red and blue light in turns, in pairing
- Put the earbuds”TWS-X10Plus” into the charging case.
- The earbuds indicator light is red when in charging.
- After full charged, the earbuds indicator light change to blue for several seconds and turn to dark at last.
Charging case capacity and charging instruction:
- LED screen shows the percentage of the case battery. Such as 50 means 50% of battery, 100 means 100% full battery capacity. Please disconnect the charging device when the case LED screen shows 100.
- Please charge for the case in DC5V/1A, it will hurt even damage the charging case if input is over 5V/1A. (Only approved Charger)
Factory reset(left and right earbuds pair again):
When charge for the earbuds in the charging case, click the two earbuds by three times until flash red light by one time.Then take out the two earbuds and touch them for 5 seconds to power off, touch them again for about 5 seconds to red and blue light flash in turns. The two earbuds is pairing each other now, the master earbuds(the right) will keep flash red and blue light, while the left flash blue light by several seconds. Turn on the mobile bluetooth to search and connect the “TWS-X10Plus”.
- Do not open and refit the earbuds in any reason, in case of damages and burning. The manufacturer do not supply warranty if that.
- Do not touch corrosive liquid with the equipment, in case of seriously damages. The manufacturer do not supply warranty if that.
- Do not put the earbuds in temperature below 0 degree or above 45 degrees.
- Avoid approaching the eyes of children or animals with the indicator lights.
- Do not use the earbuds in thunderstorm weather, which have risk of electric shock.
This product contains built-in lithium battery, do not expose under strong sunlight and throw into fire in case of explosion. Deal with batteries in accordance with local regulations, do not treat as household waste.
The user can not remove or replace the battery, which is dangerous and may damage the product. Charging as the picture indicate , tilt the headset into the charging slot.
Q: Charging case can not charge?
A: Please check the interface is plugged tight or not, and try to change a new charging cable. change a new charging cable.
Q: Earbuds can not charge?
A: Please check if the charging case have power or not. And clean the charging contacts.
Q: Earbuds can not power on?
A: Check if the earbuds have power or not, and try again.
Q: Why the mobile search out two bluetooth names of “TWS-X10 Plus’?
A: Cancel the two-TWS-X10Plus; Power off the earbuds and power on to search again.
Q: The volume is too small on the phone?
A: Try to turn up the mobile volume.
Q: How to connect two mobiles with one single earbud?
A: Connect with one mobile first, turn off the first mobile bluetooth. Then connect the earbud with another mobile. Turn on the first mobile at last.
Q: How long of the interconnection distance between the left and right earphone?
A: Within 3 meters without any obstruction.
- After receiving the product, please remove the charging protection film on the headset for the first time, and then put it into the charging case and pick it up, and it will power on it into the charging case and pick it up, and it will power on automatically. You just need to take out your phone and open the bluetooth to search the tws-x10Plus connection.
- If you need two headphones to connect two mobile phones separately, please follow the instructions to enter the single earbud mode.
- In the future, if the headset is not automatically connected to the phone, please ignore the device and search for “TWS-X10Plus” again.
- When the left and right headphones are not paired with each other, it means that you are in the single ear mode. If you restore the binaural mode, please follow the instructions to factory reset.
- The touch panel of the earphone is very sensitive. Please avoid accidental contact with the finger surface or other objects, causing the music to be paused.After you get used to it, you will feel that this function is very good.
- When your Bluetooth list searches for two -TWS-X10Plus”. Indicate that you have previously connected a single headset. You can forget these devices and search again, then turn off Bluetooth and turn it back on, a “TWS-X10Plus” will appear.
For better music experience,suggest to use 1058.0 and Android 4.3 or above operation system.
To ensure the earbuds have more longer standby time, factory stick protection films on the earbuds charging contacts. For first use, please remove the protection films first, then put the two earbuds Into the charging case, take out the two earbuds again at last. The two earbuds will power on and pair automatically.