TV-Ears-logo

TV Ears 21290 Recommended Wireless Voice

TV-Ears-21290-Wireless-Voice-Clarifying-TV-Speaker-Product

Introduction

The TV transmitter is set up with Near Field Technology which will allow it to work seamlessly as soon as both the Transmitter and Speaker are turned on and there’s an Audio connection between the transmitter and the TV. Plug in the power cord to the transmitter and make sure it is close to the TV as it needs to be connected to the TV. Once the transmitter is on, the Blue LED Ring around the TV Ears Logo will illuminate. Then connect the mini TV Transmitter with either an Optical cord (included) or an Analog cord (included) depending on the setup and TV being connected. In rare cases, a coaxial connection is the only available connection, that cord needs to be purchased separately for the transmitter and TV connection to be established. To connect the mini TV Transmitter and the speaker, now connect the Speaker at your desired location up to 100 FT from the transmitter. Once the Speaker is also turned on, it should connect automatically to the Transmitter and you will be able to enjoy the TV on your new Voice Clarifying Speaker™ with its Voice Enhancement Technology™.

Note: Since the mini TV Transmitter distributes the signal via wireless UHF broadcast, it is best to only use one transmitter per room to avoid interference.

TV-Ears-21290-Wireless-Voice-Clarifying-TV-Speaker-fig-1

TV-Ears-21290-Wireless-Voice-Clarifying-TV-Speaker-fig-2

TV•Ears Voice Clarifying TV Speaker™ Instructions

TV-Ears-21290-Wireless-Voice-Clarifying-TV-Speaker-fig-3TV-Ears-21290-Wireless-Voice-Clarifying-TV-Speaker-fig-4

DC In 12V Charging Port:

Plug in the included power cord to power on the Speaker. The speaker also contains a rechargeable battery, and will be charged when the power cord is connected to the speaker.

3.5mm Audio In Connection

For direct audio connection to a device such as an Ipad or an Iphone, plug in the included 3.5mm cord directly to both the TV Speaker and the audio device being used. When the power is low, it will be shut down automatically.

Volume Dial Control

Turning the Speaker On/OFF

  • Turn the dial clockwise to turn the speaker ON. When the speaker is turned ON, the blue LED ring around the volume dial will be illuminated. To turn it off, please turn the dial counterclockwise all the way and the blue LED light turns off.

Volume Control

  • Turn the dial clockwise to increase the volume
  • Turn the dial counterclockwise to decrease the volume.

TV•Ears Voice Clarifying TV Speaker™ Additional Controls

TV-Ears-21290-Wireless-Voice-Clarifying-TV-Speaker-fig-5

  • USB. 2.0 Port and USB-C Port: Those two plugs are used to allow charging of other portable devices such as phones or tablets. You will need to use your own cords to charge your devices.
  • Mute Button: To mute the speaker momentarily, press the mute button once. When the blue LED ring is illuminated, that means your speaker is currently muted. Press the mute button again to unmute the speaker.
  • Theater Sound Button: To activate your speaker’s theater sound mode for a better movie experience, press the Theater Sound Button once, you will see the LED light illuminate above the button. To turn the mode off, press the button again.
  • Voice Clarifying Button: To activate your speaker’s voice clarifying mode for better dialog recognition, press the Voice Clarifying Button once, you will see the LED light illuminate above the button. To turn the mode off, press the button again.

TV•Ears 5 Year limited warranty:

Welcome to the TV•Ears family and thank you for purchasing our product!

What are the terms of the warranty

This 5 year limited warranty covers product failures for a period of 5 years after the original purchase. The warranty is only valid if the product is purchased from TV•Ears directly or from one of the TV•Ears authorized resellers. During the 5 year warranty, If the product fails within the first year of the original purchase date, it will be replaced once at the cost of shipping and handling with the same or newer model. Subsequently, for the remainder of the 5 year warranty period, if the product fails it will be replaced for 50% off MSRP with the same or newer model of equal value. The following items are NOT covered under this warranty: ear tips, batteries, and shipping charges. Any replacement parts purchased at 50% off automatically extends your warranty into a new 5 year limited warranty.

How to receive warranty service or return product:

To receive warranty service or for returns, call 1-866-611-9934 to speak to our friendly American based customer support representatives. For returns, you will need to receive an RMA number and place it clearly and legibly on the outside of the package otherwise returns are not accepted. All shipping charges are NOT covered by TV•Ears

To activate your FREE 5 Year limited warranty:

Call: 1-866-611-9934

Go online: tvears.com/warranty-registration

Mail to: TV Ears, Inc. 2701 Via Orange Way, Suite 1 Spring Valley, CA 91978

FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

Frequently Asked Questions

How long do TV Ears last?

A small rechargeable battery known as the TV•Ears ® Battery Replacement can be found inside the TV•Ears ® Headset (Version 5.0). On a full charge, the batteries should last up to 6 hours per use.

Do TV Ears work on any TV?

Any television set is compatible with TV Ears, according to the manufacturer. They work with audio systems, normal TVs, cable TV, satellite TV, VCRs, and DVD players. Keep in mind that TV Ears need a battery that can be recharged and has a life of up to 4-6 hours.

How does wireless speakers work with TV?

The transmitter broadcasts audio signals to the wireless device it is linked to from the audio source (your TV). The two devices are often linked together using Bluetooth or Wi-Fi. The wireless speakers then pick up the radio waves using a receiver.

Can you use wireless speakers with a smart TV?

A Bluetooth speaker is an excellent gadget to have if you have a Smart TV. You may take your speaker around the house and connect them wirelessly so that you can… Additionally, you can utilise it with other Bluetooth-enabled gadgets like your laptop or smartphone.

How many Bluetooth speakers can you connect to a Smart TV?

You may attach two Bluetooth devices to a single TV using the Dual Audio feature. This means that two Bluetooth speakers or two pairs of Bluetooth earphones can be paired simultaneously. When you can share your Samsung Smart TV experience, you’ll enjoy it even more.

Can you use wireless headphones and TV speakers at the same time?

To enable it and output sound from both the device connected to the headphone jack or Bluetooth headphones and the TV speakers, press the HOME button, then choose [Settings] — [Display & Sound] — [Audio output] — [Audio to both TV speakers & other device].

How do wireless speakers work?

By passing alternating current through an antenna, a transmitter attached to the stereo system turns electrical signals into radio waves. From the antenna, radio waves are emitted. The wireless speaker has an antenna that detects the radio signal and a receiver that transforms it into an electrical signal.

How do you use a wireless speaker?

Connecting a Bluetooth speaker: the steps. The speaker should be in pairing mode. Turn on Bluetooth on your smartphone. Hold on while the phone connects. Play music after connecting.

Can we connect TV to Bluetooth speaker?

Go to Network Settings on your television and choose Bluetooth. Next, check the list of discoverable devices for your speaker. Hopefully, this straightforward connection approach worked.

Can you connect two speakers together?

Tap the three dots menu in the upper-right corner of prior Android versions. the Dual Audio toggle switch to on. Audio will stream to both speakers, headphones, or both if Dual Audio is enabled on the phone. The first paired device will be turned off if you add a third.

Can TV speakers and soundbar be used at same time?

When using an external sound system, such as a soundbar, your TV speakers should be completely muted or turned off. They may generate echoes when used with the soundbar, and the TV speakers have little effect on sound quality.

How do wireless speakers get power?

The majority of wireless speakers connect to standard power outlets or power strips using AC adapters. To become “truly wireless,” some systems employ rechargeable batteries, although this feature necessitates repositioning and charging as routine tasks in order to use this type of surround sound system.

What are wireless TV speakers?

Instead of using audio cords, wireless speakers use radio frequency (RF) waves to receive audio signals. A Wi-Fi variant is one of the two most often used RF frequencies for audio transmission to wireless speakers for TVs.

How do I connect my led speaker to my Bluetooth TV?

Turn on the TV to discover. Settings > Bluetooth Switch the speaker to pairing mode and turn it on. Watch for a new device to be detected by the TV. Increase or decrease the volume after connecting the speakers to your TV.

Where should I place my TV speakers?

Your television’s centre should be in line with the centre of the centre speaker. When positioned directly above or below the screen, the centre speaker should also be facing toward your seat, so be prepared to tilt it. Nothing should be in the way of your ability to view the speaker.

Leave a comment

Your email address will not be published. Required fields are marked *