tuya MX-C10 Automatic Smart Lock Installation Guide

tuya MX-C10 Automatic Smart Lock Installation Guide
tuya MX-C10 Automatic Smart Lock

Note:

  1. This lock is equipped with mechanical keys for manual unlocking. Remove mechanical keysfromthe package and keep them in a safe place and always have access to them.
  2. To power on the lock, four alkaline AA batteries(not included) are required. Non-alka-lineandrechargeable batteries ARE NOT RECOMMENDED.
  3. This lock is not designed to be exposed to direct sunlight or rain. It is not waterproof I Prated
  4. Keep your fingers clean when using this lock.

Please read this manual before operating your Smart Lock, and keep it for further reference.

Components Overview

Components Overview
Front lock x1

Components Overview
Front lock pad x1

Components Overview
Rear lock x1

Components Overview
Rear lock pad x1

Components Overview
Rear lock fixing plate x1

Components Overview
Door opening drawing x1

Components Overview
Lock body x1

Components Overview
Components Overview
Door frame stopper x1

Components Overview
35mm x4 Screw post

Components Overview
Components Overview
Components Overview
35mm x4 25mm x4 8mm x3

Components Overview
key x3

Components Overview
card x2

Components Overview
Gate magnet x1

Lock Body Overview

Front lock
Product Overview

Rear lock
Product Overview

Specifications

Material Aluminum alloy Model NO. MX-C10
Door thickness 35mm-60mm Code Length 4~8 digits
Working Temperature -20°C~70°C Working Humidity 20%~80%RH
Working Power Consumption <500mA Static Power Consumption <50uA
Power Supply 6V (4pcsAA Alkaline Batteries not included)
Unlocking Methods App Access, Fingerprint, Card, Password & Mechanical Key
User Capacity 9 Administrators
Fingerprint (100)/Card (200)/ Password (200)
Unlimited App tempera ry passwords
Product Dimension Front 62(W) x 140(H) x 16.5(D) mm
Back 70(W)x 160(H) x 28.5(D) mm

Star Icon AU specifications are subject to change without notice. All rights reserved.

Dimensions
Dimensions

Installation Guide

Installation

Note!

Check the door’s opening direction: if the front body is fastened on the left, turn the toggle button to the L, and if it is fastened on the right, tum it to the R. Make sure the thumb tum towards according to your opening direction

Right-hand door(R)
Installation

Left-hand door(L)
Installation

Kindly confirm the door’s interior thickness (Must be between38mmto 60mm)
Installation

  1. Keep the bolt closed
  2. Turn the knob properly: Fig. 1 lf you turned the toggle to R, turn the knob counter clockwise to the end (with the “dot indicator” on the knob oriented left) Fig.2
    Installation
    Installation

lf you turned the toggle to L, turn the knob clockwise to the end (with the “dot indicator” on the knob oriented upwards

Note: Before installing back body, please identify right open or left open of the door. Please follow up the below instruction to setup the right open or left open.
Installation

Deadbolt Installation

  1. Adjust the length of the bolt if it is required.
    Deadbolt Installation
  2. Install the deadbolt on the door.
    Deadbolt Installation
  3. Use a screwdriver to test if deadbolt works smoothly.
    Deadbolt Installation
  4. Make sure the bolt in retracted(unlocked) position.
    Deadbolt Installation
    Deadbolt Installation

Warning Icon NOTE: The bolt must be in retracted (unlocked) position before installing the lockset.

Lock Body Installation

  1. Hold the front body to the door, and make sure the key nail piece and cable through the door hole.
    Lock Body Installation
  2. Make sure the cable through the mounting, the position the mounting plate, then fix the front body with three screws.
    Lock Body Installation
  3. Ineart the front body cable through the rectangular hole the rubber pod. Connect the wire connector from the front body through the hole to the back body. Enrsure that the wtre is installed properly and securely.
    Lock Body Installation
    Lock Body Installation
  4. After connect the cables, make sure the thumb tum is vertical (Left opening) or horizontal (Right Opening) according to the door opening direction, then hold the back body onto mounting plate.
    Lock Body Installation
  5. Fix the back body to the mounting plate with 3 screws.
    Lock Body Installation
  6. Place the batteries, and make sure the direction of the batteries is correct, the put in the battery cover.
    Lock Body Installation
  7. Drill the strike box and strike plate according to the strike plate and strike box size, then fix them by two screws.
    Lock Body Installation
  8. If you want thelockautomatically lockedafterclose the door, pleaseinstall the door switchsensor.
    Lock Body Installation

Intelligent lock(five in one) operation manual

Function and Operation

Description of terms and functional keys

  1. Administrator information: refer to the Administrator’s fingerprint, password or IC card. Unlock information: refer to the input fingerprint, password, Remote control or IC card information (including Administrator and ordinary users).
  2. Key”Icon“: clear key/back key. Enter the password or point by clearing the previous input. Press the clear key three times in succession, empty all input.
  3. Key “Icon“: confirmation key or menu function key.

Original state

  1. The factory administrator orinitial password is 123456, under the orinitial state any fingerprint.
    IC card or password can open the lock.
  2. Any fingerprint, IC card, or password which are not registered can’t open the lock after inputting the administrator information.

Lock function management (step one)
Instructions

Administrator settings

  1. Add administrator (step 2)
    Instructions
  2. Add administrator information
    Instructions

Common user setting

  1. Add administrator information
    Instructions
  2. Delete user information
    Instructions

system setting

  1. Voice setting
    Instructions
  2. Unlock mode setting
    Instructions
  3. Language settings
    Instructions
  4. Time setting
    Instructions

Restore factory settings
Instructions

APP Configuration (Tuya Smart)

QR Code

  1. Search “Tuya Smart” in App Store or an App market, download and install it.
  2. Register with your cellphone numberand log in.
  3. Click “Security & Sensory find Lock(Wi-Fi), click and add a device following instructions before use.
  4. Remote unlocking: wake up the screen and press “9” + ” Icon” There will be a voice prompt: requesting remote  unlocking.

Add one network

  1. Press “Icon”+“Icon”to authenticate administrator identity and then press “T” to access administrator settings. Then there will be a voice prompt of pressing “3” for network configuration.
  2. Voice prompt in network configuration mode: press 1 for hotspot connection and 2 ^ * for intelligent connection
  3. When the network is successfully added, the 1, 2, 3 and 4 lights on the keyboard will be on in order with a voice prompt of “operation completed
  4. In the event of network addition failure, the 1, 2, 3 ^ (a*t_{1}) 4 lights on the keyboard will not be on and there will be a voice prompt of “operation failed” upon timeout

Notice:

  1. Please add administrator before setting.

Other notes

  1. Under factory default, input 369 Icon or 1476 Icon to change handle direction
  2. Press the lock key can lock the lock automatically
  3. Input the wrong password more than 5 times in arow, the keyboard locked for 30 seconds, it does not respond to any operations in 30 seconds
  4. Password peeping prevention function input password as follows when opening the door with password: XXX password XXX, you can add some extraneous codes before and after the password, and then press fi to confirm. The password must be included in the input contents
  5. If there is no operation more than 10 seconds, system will automatically exit,
  6. After the voltage is lower than 4.liv, the lock will automatically alarm every time when it is opened. After the alarm, the lock can be opened for about 200 times.
  7. Remove the battery cover press the “Set” key for 6 seconds the lock was restored to factory mode;
  8. In factory mode, input “3336669996 Icon° cna change the language quickly,
  9. When unlocking input “5Icon” to enter passage mode(One time effective);
  10. When unlocking input “Icon” to broadcast the user number;

Technical Parameters

Technical Parameters
Items Parameters Memo
1 Static current ≤50uA
2 Dynamic current ≤500mA
3 Administrators number 9
4 Fingerprint number 100
5 Fingerprint + password + card capacity 200
6 Fingerprint Sensor Semiconductor
7 Fingerprint contrast time ≤0.6Second
8 Fingerprint identification Angle 360°
9 False Rejection Rate ≤0.1%
10 False Recognition Rate ≤0.0001%
11 Reaction time ≤0.1 Second
12 Power type 6V
13 Emergency power 5VDC
14 Working temperature -25°C~60°C
15 Working Relative Humidity 20%~90%RH
16 Human voice Yes
17 Keyboard Touch standard 12-bit keyboard
18 Password Length 4-8 digits
19 Phantom password 32 digits
20 Low voltage alarm 4.6±0.2V
21 Unlock time ≤1 Second

QR Code
QR Code
App

MAIN FUNCTION MODULES

LAPP REGISTRATION AND LOGIN

  • APP registration: if you do not have an APP account, you can choose to register or log inby SMS verification code.
  • Click “create a new account to enter the account registration page. According to the prompt to obtain SMS verification code, set the password.
  • If you have an existing account, click “login with an existing account to log in to the APP. Password, verification code, and social account login are supported.
    Registration Login
    Registration Login

CREATE HOMES

  • Create your home after registering and logging in successfully.
  • Each account can create and add multiple homes, and devices can be grouped by room in the home.
  • Weather and other functions depend on the geographical location of the family, which is recommended to set in advance.
    Create Homes

ADD WIFI LOCK

  • On the Tab of “my home”, click”+” in the upper right corner to enter the interface in figure 1, select the WiFi door lock in security sensor part and enter the page in figure 2.
    Add WIFI Lock
    Add WIFI Lock
  • When the device enters the connected mode, continue to operate according to the instructions and APP tips.

HOME PAGE

  • Home page includes remote unlock, alarm message, member management, record, temporary password and other functions.
  • Remote Unlock: initiate a request from the door lock, and the app can respond to allow / refusal door opening
    Home Page

DYNAMIC PASSWORD

  • Click to get the dynamic password Meanwhile copy the password text for you
    Dynamic Password

MESSAGE CENTER

  • Message center contains alarm information, doorbell call information and hijacking alarm information, which can be inquired.
    Message Center

USER MANAGEMENT

  • User can be added, deleted or changed in member management. Only the administrator user of app is allowed to do that.
    User Management

RECORD LOG

  • 24/7 Record Log, arranged in reverse chronological order. The unlocked ID with the associated user name will directly display the user name, while the unlocked ID without the associated name will display the specific unlock ID
    Record Log

TEMPORARY PASSWORD

  • Temporary password can be created and deleted through app. After each create or delete is completed on the app, the lock hardware is required to synchronize with the server.
  • At the time of creation, you can choose whether to send SMS or not. Worldwide SMS is supported.
    Temporary Password
    Temporary Password

HIJACKING ALARM

  • When the anti-hijacking mark in the left picture is opened, if the unlock action of the unlock ID occurs, the record will report and the app will trigger the anti-hijacking alarm
    Huacking Alarm

FACTORY DATA RESET

  • Click the icon in the upper right corner of the main interface. Find the Factory Data Reset and click
  • The Factory Data Reset can also be operated on the lock. Please refer to the instruction manual for details.
    Factory Data Reset
    Factory Data Reset

FOC WARNING This device complies with part 15 of the FCC Wiles. Operation in subject to the following tan conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause mdesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has heen tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. I however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause haraful interference to radisar television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference hy one or mure of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation hetween the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver in connected.
  • Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FOCIF Exposure guidelines. This equipment should be installed and operated with minimm 20cm distance hetween the radiator and your hody: Use only the supplied antenna.

Documents / Resources

PDF thumbnailMX-C10 Automatic Smart Lock
Installation Guide · MX-C10, 2BHDK-MX-C10, 2BHDKMXC10, MX-C10 Automatic Smart Lock, MX-C10, Automatic Smart Lock, Smart Lock

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.