TRUTLEBEACH Stealth 600 Wireless Transmitter User Guide

a close up of an office chair

 

Package Contents

A. Stealth 600 Headset

a drawing of a face

B. Stealth 600 Wireless Transmitter

graphical user interface

C. USB Charging Cable

Headset Controls

diagram

Superhuman Hearing 

Use Superhuman Hearing Mode to pinpoint quiet audio cues like enemy footsteps and weapon reloads.

Setup for PS4 Pro Configuration

  1. Connect Transmitter to USB Port

    diagram

  2. Power on Headset
    a drawing of a face
  3. Audio Devices
    graphical user interface, application

Go to Settings >> Devices >> Audio Devices.

  1. Select Stealth 600 for Input & Output Device.
  2. Set Output to Headphones to All Audio. 
  3. Set Volume Control (Headphones) level to maximum.
  4. Select Adjust Microphone Level and follow the on-screen instruction to calibrate your microphone.

Charging

The Stealth 600 uses a rechargeable battery. Make sure to charge it regularly.
Headset Storage
Always charge your headset before storing it for any extended period of time (greater than 3 months). Never store the unit in temperatures above 113°F/45°C.

Pairing

The Stealth 600 Headset and Transmitter come paired out of the box. When paired, with both the Headset and Transmitter powered on, the Transmitter’s LED will be on solid ( lit, but not blinking). However, if your Transmitter’s LED is double-blinking, follow the steps below to pair your Headset and Transmitter.

  1. Start this process with the headset powered OFF. Press and hold the Pairing Button on the Transmitter until the Transmitter’s Pairing LED flashes rapidly, then release. (Use a Paperclip or something similar to press the Pinhole button).

    diagram

  2. Press and hold the Power Button on the Headset until the Headset’s Power LED flashes rapidly (5 seconds), then release.

    a drawing of a face

  3. Within 10 seconds, the Transmitter’s and Headset’s LED will remain on solid, indicating that pairing has been successful.

For additional Information Visit:
www.turtlebeach.com/support 

Regulatory Compliance Statements for the EAR FORCE Stealth 600P RX & TX

Federal Communications Commission (FCC) Compliance Notices

This section includes the following FCC statements for the EAR FORCE Stealth 600P RX & TX:

  • FCC ID: XGB-TB3340 (RX) & XGB-TB3341 (TX)
  • Non-Modification Statement
  • Class B Interference Statement
  • RF Radiation Exposure & Hazard Warning

Class B Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment doesn’t cause harmful interference to radio or television reception, which can be diminished by turning the equipment off and on, the user is encouraged lo try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] This device may not cause harmful interference, and (2) thls devlce must accept any interference received, Including interference that may cause undesired operation.

RF Radiation Exposure & Hazard Statements:
To ensure compliance with FCC RF exposure requirement, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.] from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. lnstallers or the radio and and users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Non-Modification Statement:
Use only the supplied Internal antenna. Unauthorized anlennas, modifications, or attachments could damage the EAR FORCE Stealth 600P RX & TX Models and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Please contact Turtle Beach for a list of approved 2.4 GHz antennas.

This product is compliant with the Consumer Product Safety Improvement Act of 2008, Public Law 110-314 (CPSIA)

Canadian ICES Statements IC: 3B79A-TB3340 (RX) and IC: 38791A-T83341 (TX)
This device complies with ICES-003 and RSS-247 of Industry Canada. Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any Interference, Including interference that may cause undesired operations of the device.

RF Radiation Exposure & Hazard Statement
To ensure compliance with RSS-102 RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the IC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction wilh any other antenna or transmitter.

European Union and European Fair Trade Association Regulatory Compliance:
This equipment may be operated in the countries that comprise the member countries of the European Union and the European Fair Trade Association. These countries, listed below, are referred to as The European Community throughout this document: AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA, FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA, LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, UNITED KINGDOM, ICELAND, LICHTENSTEIN, NORWAY, SWlTZERLAND.

This equipment meets the following conformance standards: Safety:
EN 60950-1: A11:2009+A1:2010+A12:2014 (T-Mark License), IEC 60950:2005 (2nd Ed.)+ Am1: 2009 + Am 2: 2013 (CB Scheme Certificate), EN 50332-1: 2013, EN 50332-2: 2013, EN 71-3: 2013 Additional licenses issued for specific countries are available on request.

WARNING!
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case, the user is required to take appropriate measures.

This symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.

Documents / Resources

TRUTLEBEACH Stealth 600 Wireless Transmitter [pdf] User Guide
Stealth 600 Wireless Transmitter, 426-155-001-001 RC

References

Leave a comment

Your email address will not be published.