Tribit True Wireless Earbuds BTH90 User manual

Tribit True Wireless Earbuds BTH90 User manual

Thank you purchasing Tribit True Wireless Earbuds! Please read this user manual carefully and keep it for future reference.

What’s Inside?

Tribit True Wireless Earbuds BTH90 - Box Content

Product Illustrations

Tribit True Wireless Earbuds BTH90 - Product Illustrations

Fitting or replacing the ear tips

Tribit True Wireless Earbuds BTH90 - Fitting or Replacing the Ear Tips

How to wear the earbuds

Tribit True Wireless Earbuds BTH90 -How to wear the earbuds

Powering on and off

When using for the first time, firstly remove the protective tape from the earbuds, place them back into the charging case and close the case immediately.

Tribit True Wireless Earbuds BTH90 - Powering on and off

How to pair the earbuds

  • Left & right earbud pairing

When you open the charging case, the earbuds will automatically enter TWS pairing mode, and the blue light will flash quickly.

  • Pairing the earbuds to your cell phone

When pairing for the first time, open the charging case and the earbuds will automatically complete TWS pairing mode. Then it will enter the cell phone pairing mode ( blue and red lights will flash alternately). Then activate Bluetooth on your cell phone and select “Tribit Fly Buds” from the list of available devices. You’ll know the pairing is successful when the blue LED light flashes every 5s.

Tribit True Wireless Earbuds BTH90 - Pairing the earbuds to your cell phone

To connect another cell phone, touch the touch button 5 times to disconnect the current device, then enter manual pairing mode.

  • Mono mode

To pair only one earbud, remove one earbud from the charging case and leave the other inside. Then close the charging case immediately, and the earbud you removed will enter mono mode automatically.

Tribit True Wireless Earbuds BTH90 - Mono mode

Charging

  • Charging the earbuds
    Place the earbuds into the charging case and close the lid. The charging LED indicator light will stay red while charging, and will turn off if the earbuds are sufficiently charged ( about 90 min).
  • Charging the charging case
    Connect the charging case to a type C cable. You’ll know the case is charging when you see the green LED light pulsing. It will stay on and glow solid green on once fully charged ( about 120 min).

Battery level LED Indicator

Tribit True Wireless Earbuds BTH90 - Battery level LED Indicator

Earbud LED Indicator

Pairing to cellphone: Blue and Red LED lights will flash alternately
Pairing left and right: Blue LED light will flash quickly
Connection successful: Blue LED light will flash every 5s
Battery low: Red LED light will flash slowly

Operating instructions

Tribit True Wireless Earbuds BTH90 - Operating instructions

Reset the earbuds

If there is no response from the touch button, or the earbuds don’t work normally, you may need to conduct a manual reset. Please do the following:

Step 1. Touch and hold the touch button for 6s to power off the ear buds
Step 2. Touch and hold the touch button for 12s, and the blue LED will flash 4 times if the reset is successful
Step 3. Place the earbuds into the charging case and close it. Then reopen the charging case again and try using the earbuds

Note: Before step 3, please make sure the left and right earbuds have been reset successfully ( the blue LED will flash 4 times if the reset is successful ).

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (l)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Tribit True Wireless Earbuds BTH90 User manual – Optimized PDF
Tribit True Wireless Earbuds BTH90 User manual – Original PDF

Leave a comment

Your email address will not be published. Required fields are marked *