Wintact El Tipi Anemometre WT816 Kullanım Kılavuzu

1. Giriş

This manual provides detailed instructions for the proper use and maintenance of your Wintact Handheld Anemometer, Model WT816. This device is designed for accurate measurement of air velocity and temperature, making it suitable for various applications including HVAC system checks, outdoor activities like sailing and kite flying, and general environmental monitoring.

The WT816 is a compact, lightweight, and multifunctional tool featuring a high-precision pressure sensor, data hold function, and a backlit LCD screen for clear readings.

2. Temel Özellikler

• Fast & Accurate Measurement: Provides precise wind speed readings from 0.3 to 30 m/s with ±5% accuracy.
• Sıcaklık İzleme: Measures air temperature from 14°F to 113°F (-10°C to 45°C) and displays wind chill.
• Çoklu Birimler: Supports m/s, ft/min, knots, km/h, and mph for wind speed, and Beaufort scale display.
• Taşınabilir Tasarım: Ultra-compact and lightweight (0.14lb) for easy carrying in a pocket or backpack.
• Çok Fonksiyonlu Ekran: Features a bright LCD screen with backlight, showing current, maximum (MAX), and average (AVG) wind speeds.
• Dayanıklılık: Equipped with an anti-slip, anti-fall rubber jacket for enhanced protection.
• Kolaylık: Includes a low battery indicator and an auto power-off function.

3. Paket İçeriği

Paketi açtığınızda lütfen aşağıda listelenen tüm öğelerin mevcut ve iyi durumda olduğundan emin olun:

• 1x Wintact Anemometer (WT816)
• 1x 3.0V CR2032 battery (pre-installed or included separately)
• 1x Kullanım Kılavuzu
• 1x Boyun Askısı

4. Kurulum

4.1. Pil Kurulumu

The Wintact WT816 Anemometer uses one 3.0V CR2032 Lithium Metal battery. If the battery is not pre-installed or needs replacement, follow these steps:

1. Carefully remove the red rubber protective cover from the device.
2. Locate the circular battery compartment on the back of the unit.
3. Use a coin or a flat-head tool to twist the battery cover counter-clockwise to open it.
4. CR2032 pili pozitif (+) tarafı yukarı bakacak şekilde yerleştirin.
5. Replace the battery cover by twisting it clockwise until secure.
6. Re-attach the red rubber protective cover.

4.2. İpin Takılması

Thread the included lanyard through the designated loop at the bottom of the anemometer for secure handling and to prevent accidental drops.

5. Kullanım Talimatları

5.1. Güç Açma/Kapatma

• Açmak için: Press the "MODE" button for 2 seconds. The LCD will display air velocity, temperature, and battery icon. The backlight will activate for 12 seconds.
• Otomatik Kapanma: The unit will automatically shut off after 14 minutes of no operation to conserve battery life.
• Manuel Güç Kapatma: Press the "MODE" and "SET" buttons simultaneously to turn off the unit.

5.2. Arka Aydınlatmalı Ekran

Press any button to activate the backlight for 12 seconds, improving visibility in low-light conditions.

5.3. Selecting Wind Speed Units

The anemometer supports five units of air velocity: meters per second (m/s), kilometers per hour (Km/h), feet per minute (ft/min), knots, and miles per hour (mph).

1. With the unit turned on, press the "MODE" button for more than 3 seconds until the current unit (e.g., "m/s") starts to blink.
2. Press the "SET" button repeatedly to cycle through the available units.
3. Once your desired unit is displayed, press the "MODE" button to confirm and save the selection.

5.4. Selecting Measurement Mode (Current, MAX, AVG, Wind Chill)

The WT816 can display current, maximum (MAX), and average (AVG) wind speeds, as well as wind chill.

1. After setting the desired air velocity unit (as described in 5.3), press the "SET" button repeatedly.
2. Cycle through the modes until "CU" (Current), "MAX" (Maximum), or "AVG" (Average) blinks. The wind chill value will be displayed when the temperature is below 0°C (32°F).
3. Press the "MODE" button to confirm your selection. The setting will be stored even after the unit is turned off.

5.5. Selecting Temperature Units (°C/°F)

To switch between Celsius (°C) and Fahrenheit (°F) for temperature display:

1. Remove the red rubber protective cover.
2. Locate the small push-button switch labeled °C/°F inside the rear cabinet, near the battery compartment.
3. Use a small pointed object (like a pen tip) to press this button to toggle between °C and °F.
4. Re-attach the rubber protective cover.

6. Bakım

6.1. Temizlik

Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the impeller area is free from dust and debris for accurate readings.

6.2. Pil Değişimi

When the low battery indicator appears on the LCD, replace the CR2032 battery by following the steps outlined in Section 4.1.

6.3. Depolama

Store the anemometer in a cool, dry place, away from direct sunlight and extreme temperatures. If storing for extended periods, it is recommended to remove the battery.

7. Sorun Giderme

• Ekran Yok/Ünite Açılmıyor: Pilinin doğru takılıp takılmadığını ve yeterli şarjı olup olmadığını kontrol edin. Gerekirse pili değiştirin.
• Yanlış Okumalar: Ensure the impeller is clean and unobstructed. Make sure the device is held in a clear airstream, away from your body or other objects that might interfere with airflow.
• Settings Resetting: This may indicate a loose battery connection. Ensure the battery is securely seated in its compartment and the cover is tightly closed.
• Arka Işık Çalışmıyor: Check battery level. If the battery is low, the backlight may not function optimally.

8. Özellikler

9. Garanti ve Destek

9.1. Garanti Bilgileri

The Wintact Handheld Anemometer WT816 comes with a 12 ay garanti Satın alma tarihinden itibaren geçerli olmak üzere, üretim hataları ve işçilik kusurlarını kapsar. Garanti talepleri için lütfen satın alma belgenizi saklayın.

9.2. Müşteri Desteği

For any questions, technical assistance, or warranty inquiries, please contact the Wintact customer service team. They are available 24/7 to provide professional support.

• Üretici: Wintact
• E-posta: wintact01@outlook.com
• Webalan: http://www.wintact.net