PowMr 4200W Güneş İnverteri Kullanım Kılavuzu

1. Giriş ve Üzeriview

This user manual provides detailed instructions for the installation, operation, and maintenance of the PowMr 4200W Solar Inverter. This all-in-one hybrid inverter integrates inverter, solar charger, and battery charger functions to provide uninterruptible power support. It is designed for off-grid applications and is compatible with both lead-acid and lithium batteries.

Temel özellikler şunlardır:

• Pure Sine Wave Inverter with 220-230VAC output.
• Integrated 120A MPPT Solar Charge Controller.
• Maximum PV Array Power: 6200W.
• Supports various battery types including Lead Acid and Lithium.
• Multiple charging modes: Utility/Solar Priority, Hybrid, and Battery+Solar.
• Built-in safeguards against short-circuit, over/under-voltage, overload, and backfeed.
• One-click restore to default settings function.

Şekil 1.1: Ön view of the PowMr 4200W Solar Inverter.

2. Ürün Bileşenleri ve Şeması

İnverterin ana bileşenlerini ve bağlantı noktalarını tanıyın:

Figure 2.1: Detailed component diagram of the PowMr 4200W Solar Inverter.

1. LCD ekran
2. Durum göstergesi
3. Şarj göstergesi
4. Arıza göstergesi
5. İşlev düğmelerine dokunun
6. Güç AÇIK/KAPALI anahtarı
7. AC girişi
8. Ana çıktı
9. İkinci çıkış
10. PV 1 ve PV 2 girişi
11. RS232/WIFI/Uzaktan LCD İletişim Portu
12. Pil girişi
13. Toz önleyici kapak

3. Kurulum ve Kurulum

Installation of the PowMr 4200W Solar Inverter should be performed by qualified professionals to ensure safety and compliance with local electrical codes. Ensure the installation environment is well-ventilated, dry, and free from direct sunlight or excessive dust.

3.1 Kablolama Şeması

The following diagram illustrates a typical connection setup for the inverter with solar panels, batteries, and AC loads:

Figure 3.1: Typical wiring diagram for the PowMr 4200W Solar Inverter.

Önemli Hususlar:

• Pil Bağlantısı: Connect 24V lead-acid or lithium batteries to the battery input terminals. Ensure correct polarity.
• PV Girişi: Connect solar panels to the PV 1 and PV 2 inputs. Ensure the maximum PV open circuit voltage (500VDC) and power (6200W) are not exceeded.
• AC Giriş/Çıkış: Connect to the utility grid or generator for AC input, and to your household appliances for AC output. Note that this is a single-phase 220-240V output inverter. A transformer may be needed for 110V systems.
• Topraklama: Always ensure proper grounding for safety.

4. Operating Instructions and Settings

The inverter features an LCD display and touch function buttons for configuration. Below are key settings and their functions. For a visual guide, refer to the official setting guide video.

4.1 Ayarlar Menüsüne Erişim

After powering on, long-press the GİRMEK key on the main screen to access the settings menu.

4.2 Key Settings Overview

• Setting 00: Restore Function
  Used to reset the inverter, restoring all settings to factory defaults.
• Setting 01: Output Source Priority
  Configures the output power priority. Options include:
  • SUB Priority: Solar > Grid > Battery. Suitable for areas with unstable grid power or long-term battery usage.
  • SBU Önceliği: Solar > Battery > Grid. Solar is top priority, battery supplements when solar is insufficient or at night, grid is used only when battery voltage is low. More suitable for areas with higher electricity prices.
  • USB Priority: Grid > Solar > Battery. Grid power takes precedence, with solar and battery activating when grid power is unavailable. More suitable for regions with relatively lower electricity rates.
  

  Figure 4.1.1: Output Source Priority options.
• Setting 02: Maximum Charging Current
  Sets the maximum charging current of the inverter (sum of grid and solar charging).
• Setting 03: AC Input Voltage Aralık
  Configures the AC input voltage range. APL mode has a wider range for different grid environments, while UPS mode has a narrower range for sensitive electronic devices.
• Setting 05: Battery Type
  Selects the battery type (AGM, Flooded Lead-Acid, USE, LIB, LIC, LIL). USE and LIB options allow custom parameter configuration in settings 26, 27, and 29. LIC and LIP are for Pace battery's 232 and 485 communication protocols, respectively. LIL is for Pylontech batteries.
• Setting 06: Automatic Restart Function When Overload
  Enables or disables automatic restart during overload.
• Setting 07: Automatic Restart Function When Over-temperature
  Enables or disables automatic restart during over-temperature.
• Setting 09: Output Frequency
  Sets the system output frequency (50Hz or 60Hz).
• Setting 10: Output Voltage
  Çıkış hacmini ayarlartage.
• Setting 11: Maximum Grid Charging Current
  Sets the maximum charging current from the grid.
• Setting 12: Voltage Threshold for Battery-to-Grid Switching
  ses seviyesini ayarlartage when switching priority power source from battery to grid in SBU or SUB priority.
• Setting 13: Voltage Threshold for Grid-to-Battery Switching
  ses seviyesini ayarlartage when switching priority power source from grid to battery in SBU or SUB priority.
• Setting 16: Charging Source Priority
  Sets the charging source priorities:
  • SNU Mode: Both solar and grid power charge the battery simultaneously with equal priority.
  • OSO Mode: Only solar charges the battery; the grid does not participate.
  • CSO Mode: Solar has a higher priority for battery charging; the grid charges the battery only when solar is unavailable.
  

  Figure 4.2.1: Charging Source Priority options.

• Setting 18: Alarm Function
  Enables or disables the inverter's alarm function.
• Setting 19: Auto Return to the Main Screen
  Enables or disables the automatic return to the main screen function.
• Setting 20: Backlight Function
  Enables or disables the backlight function.
• Setting 22: Beeps While Primary Source is Interrupted
  Enables or disables the power source blocked alarm function. If the priority power source is blocked for various reasons, the inverter will issue an alarm.
• Setting 23: Overload Bypass
  Enables or disables the overload bypass function. If enabled, when the inverter is in battery mode and the load experiences an overload, it will switch to grid mode, providing continued power to the load to ensure stable power supply.
• Setting 25: Record Fault Code
  Enables or disables the fault code recording function. If enabled, you can view fault records through the Wi-Fi module connected to the mobile app or by connecting to the upper computer software.
• Setting 26: Constant Voltage Şarj Hacmitage
  Configures the constant voltage şarj hacmitage (crucial for charging, refer to battery manual).
• Setting 27: Float Charging Voltage
  Configures the float charging voltage (crucial for charging, refer to battery manual).
• Setting 29: Low-voltage Kesme Hacmitage
  Configures the low-voltage kesme hacmitage (crucial for charging, refer to battery manual).
• Setting 30: Equalization Function
  Enables the battery equalization function. If the selected battery type is Flooded or another type that accepts equalization, this function can be enabled. After enabling, you can configure settings 31 to 36.
• Setting 31: Equalization Charging Voltage
  Pil dengeleme ses seviyesini ayarlar.tage.
• Setting 33: Duration of Equalization Charging
  Sets the duration of equalization charging.
• Setting 34: Equalization Charging Voltage (Extended Time)
  Sets the extended time of equalization charging. If equalization charging reaches the duration set in setting 33 but the battery voltage has not reached the equalization voltage set in setting 31, the inverter will extend the duration by the time set in setting 34.
• Setting 35: Equalization Interval
  Sets the equalization interval (how often equalization charging occurs).
• Setting 36: Equalization Activated Immediately
  For immediately enabling or disabling equalization.
• Setting 37: Grid-tied Operation
  Switch for grid-tied operation. Note: Grid-tied operation should be performed by professionals and comply with local grid specifications.
• Setting 38: Grid-tied Output Current
  Sets the grid-tied output current.
• Setting 39: Switch of the LED Light
  Enables or disables the LED light.
• Setting 41: Dual-output Function
  Enables the dual output function. This mode is mainly used to terminate one non-essential output when the battery level is low, ensuring the stability of the other output. This avoids the situation where all connected loads are affected in single output mode.
• Setting 42: Exit Dual-output Mode
  Hacmi yapılandırırtage value to exit dual output mode.

5. İzleme ve Göstergeler

The inverter provides visual indicators and remote monitoring capabilities:

5.1 LED Pattern (RGB Light for Different Working Mode)

Figure 5.1.1: LED patterns indicating different working modes.

• Sabit Mod: No specific color mentioned, implies idle or normal state.
• PV Modu: Purple Light (Indicates power is primarily from PV/Solar).
• Fayda Modu: Blue Light (Indicates power is primarily from the utility grid).
• Pil Modu: Red Light (Indicates power is primarily from the battery).

5.2 Remote Monitoring via App

The inverter supports remote monitoring and control via the "SMARTESS" app. A Wi-Fi module and GPRS data need to be purchased separately for this functionality.

Figure 5.2.1: Remote monitoring and control via the SMARTESS app.

Download the app from the App Store or Get it on Google Play.

For more information on the Wi-Fi module, refer to the product information with code Q2721100111238.

6. Sorun Giderme

The inverter is equipped with various protection features. In case of an issue, the fault indicator (4) on the diagram will illuminate, and an alarm may sound if enabled (Setting 18). Fault codes can be recorded (Setting 25) and viewed via the mobile app or computer software for diagnosis.

Yaygın sorunlar ve olası çözümleri:

• Aşırı yük: If an overload occurs, the inverter may automatically restart (Setting 06). Reduce the connected load.
• Aşırı sıcaklık: Ensure adequate ventilation around the inverter. Check for obstructions in cooling vents. Automatic restart may occur (Setting 07).
• Pil Hacmitage Düşük: Check battery connections and charge level. Ensure proper charging source priority (Setting 01, 16) and battery type (Setting 05) are configured.
• Grid Power Interruption: The inverter will switch to battery or solar power based on priority settings. If the primary source is interrupted, an alarm may sound (Setting 22).

For persistent issues or complex fault codes, please contact PowMr customer support or a certified technician.

7. Özellikler

Below are the detailed technical specifications for the PowMr 4200W Solar Inverter (Model: POW-HVM4.2M-24V-N):

Table 7.1: Technical Specifications. For more detailed specifications, refer to the product label with code 920422405060107.

8. Güvenlik Bilgileri

Always adhere to the following safety guidelines when installing, operating, or maintaining the PowMr Solar Inverter:

• Kurulum ve çalıştırmadan önce kullanım kılavuzunun tamamını okuyun.
• Elektrik tesisatı işleri yalnızca yetkili personel tarafından yapılmalıdır.
• Tüm bağlantıların güvenli olduğundan ve doğru polariteye uyulduğundan emin olun.
• İnvertörü ıslak ortamlarda veya yanıcı maddelerin yakınında çalıştırmayın.
• Aşırı ısınmayı önlemek için yeterli havalandırmayı sağlayın.
• İnverteri kendiniz açmaya veya onarmaya çalışmayın. Yetkili servis personeliyle iletişime geçin.
• Disconnect all power sources (PV, battery, AC) before performing any maintenance or service.

9. Garanti ve Destek

For warranty information, technical support, or service inquiries, please contact PowMr customer service through their official channels. Keep your purchase receipt and product model number (POW-HVM4.2M-24V-N) handy for faster assistance.

Ziyaret edin PowMr Mağazası Amazon'da Ek ürünler ve destek kaynakları için.