TOORUN M26 Bluetooth Headset with Noise Cancelling
- Power on: Press3 seconds, and the blue light flicker.
- Power off: Press 5 seconds, and the red light flicker.
- Paring: First use, boot into pairing mode automatically. Non-first use, press 8 seconds, the red and blue lights flash alternately, then it is time to pair.
- Connect to phone: Turn the phone’s Bluetooth on and search for new Bluetooth devices, select your headset to connect.
- Answer the call
- Refuse the call
- Redial the last dialing
- Switch call mode between the phone and the headset
Press 3 seconds during the conversation.
- Track Controls
Previous track Press 3 seconds. Next track Press 3 seconds.
- Volume up
- Volume down
Switch between calls
Double click will keep the present call and turn to the new call. Double click again will switch back.
Connect two phones
- Pair with the first mobile phone, then turn off the BlueTooth headset and the Bluetooth of the first mobile phone.
- Turn on the headset again, and pair it with the second mobile phone as normal.
- Turn on the Bluetooth of the first mobile phone again, now the headset will connect with two phones simultaneously.
Make sure to charge it fully before putting it to use. Charge fully when the red light turns to blue. When the light turns to be red, it means the battery low and will have a voice prompt.
IOS battery status display.
Reset to defaults
In the state of power-on,press and simultaneously until the red and blue lights flicker.
- Please do not dismantle or modify the headphone for any reason, otherwise, it may cause a fire, or damage the product completely.
- Please do not put the product in the environment at too high or too low(below 0 ℃ or above 45 ℃) temperature.
- Please keep out of the eyes of children or animals when the light flickers.
- Please do not use the product when there is a thunderstorm, or the product may be abnormal and increase the risk of electric shock.
- Please do not wipe the product with oil or other volatile liquid.
- Please do not wear this product to swim or shower, do not soak the product.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The wood may have absorbed moisture from the air in your attic. This can cause the wood to appear wet even though it is dry. If you are concerned about the moisture content of your wood, you should use a different method to determine if it is dry enough for use. For example, you could use a moisture meter that measures the moisture content of wood by using a probe that is inserted into the wood (see “Moisture Meters for Wood” on page 2).
A Bluetooth® gadget connects to your mobile phone, smartphone, or computer using radio waves rather than wires or cables. Millions of the goods we use on a daily basis employ the Bluetooth wireless short-range communications technology standard, including headsets, smartphones, laptops, and portable speakers.
Nonionizing radiation is produced at low levels by Bluetooth devices. Humans are not harmed by modest doses of this kind of radiation exposure. Routine exposure to nonionizing radiation is “usually considered as innocuous to humans,” the Food and Drug Administration (FDA) claims.
Android’s media playback will not send audio to a connected Bluetooth device using the Hands-Free Profile because this Profile is normally used to make phone calls from your phone.
Only one hour a day is advised by the World Health Organization (WHO) for Bluetooth headphone use.
True wireless headphones typically have a battery life of 3 hours or less before they run out of juice. Charger cases come in handy in this situation. A good charging case can extend the listening period of your headphones by at least 5 to 6 hours.
No, the product is certified to survive immersion in fresh water for 30 minutes at a depth of 1 metre at the IPX7 standard. However, Bluetooth signals cannot pass through water, making it impossible to make or receive calls when underwater and to stream music.
Even if your phone doesn’t already have the feature built, you can still tune in and listen to the radio with Bluetooth headsets.
Bluetooth is a wireless technology that enables communication between two compatible devices. You can use a mobile phone “hands-free” in a car, which means you don’t have to hold it when using features like the address book or placing or receiving calls.
Phyllis Zee, chief of sleep medicine at Northwestern University’s Feinberg School of Medicine, believes that although the effects of sleeping while using headphones have not been well researched, they are usually considered to be safe.
Bluetooth headphones include a rechargeable battery that is incorporated right into them. Large batteries that can be charged via a USB connection are built into over-ear Bluetooth headphones. Battery life should be between 20 and 30 hours; the JBL Everest, for example, makes a 25-hour battery life guarantee.
In Bluetooth headsets, batteries are typically not replaceable; however, this depends on the particular headset you’re using.