TMT AUTOMATION CB19 Control Box For Hermit

Control Box Installation

1. Decide the installation position of the control box first, it is suggested to be installed near the gate and should be protected from possible damage. Be aware of the motor cable length before deciding the installation position.
2. Remove the cover by unscrewing the four screws on the cover. See Figure A.
3. Use a screwdriver to puncture the holes beneath the bottom of the control box. See Figure B.
4. Secure it on the wall Figure C.

Wiring Connection

Motor Connection

• a. Motor Only
• b. Motor With Limit Switch + LED indicator
• c. Motor With Hall Sensor

Wifi Device

• Functions of Buttons and Terminals
• LED Description:
  • Blue: LED will be flashing during WIFI pairing, and be ON when completed.
  • Green: LED will be flashing if WB-001 receives a signal from the APP. If your home WIFI disconnects, the green light will continuously flash, and it will be off until WIFI is connected again.
  • Red: System failure or wrong PIN.

Back-up Batteries

Battery Power:

• The battery white connector must be fitted the correct way round (positive red to +positive) or you will short circuit the control board. There are 2 x 12v batteries fitted under the control board.
• They are connected in series to make 24vDC via a black cable with a yellow fuse with the positive of one battery to the negative of the second battery.
• The remaining positive and negative terminals go to the control board as per the photo above.

Accessories

• a. Photocells
  • The safety photocells are security devices for controlling automatic gates. Consists of one transmitter and one receiver based on waterproof covers; it is triggered while breaking the path of the beams.

Specification

INSTALLATION

1. Open the cover and connect the wires.
2. Mounted the receiver and transmitter in the proper position.
3. Ensure there are no obstacles between the receiver and the transmitter.
4. For optimal efficiency, the receiver and transmitter should be properly aligned.
5. Power up the photocells and make sure the LED light on the receiver and transmitter are ON.

Get Started

Note:

• A. Transmitter memorizing must be done first before system learning.
• B. CHECKING THE Gate MOVEMENTS
  • Release the gearmotor with the release key and move the gate to the middle so that it is free to move in both opening and closing directions; then lock the Gearmotor.
  • Perform the gate opening and closing several times and make sure the gates touch the limit switch at least 2~3 cm before the mechanical stop.

1. Step 1: Remote Memorizing
   • a. Memorizing
     1. Press the button RF-Learn on the control board (Figure 1) as many times as the number corresponding to the desired command, according to the following table, Within 10s, press the desired button on the remote that you want it to be memorized (Figure 1)
        

        Times for pressing RF-Learn	Command	Message code
        1 time	Open-Stop-Close circle	OLED display “OSC”
        2 times	Pedestrian mode	OLED display “PED”

     2. Make sure that the LED display shows the “OSC” or “PED” three times quickly. The code is corresponding to the selected command. (Figure 2)
     3. Repeat steps 1 & 2 within 10, if there are other remotes to be memorized for the same type of command. If no action is within 10s, the memorization stage will terminate automatically.
   • b. Remote learning without a Control board
     1. Press the button on the NEW radio transmitter and hold it down for at least 5s, then release it.
     2. Press the button on the OLD radio transmitter 3 times. (Tip: Don’t press too fast; make sure you see the blue flash when pressing the button each time.)
     3. Press the button on the NEW radio transmitter once.
     4. Done, at this point, the NEW radio transmitter will copy the same command as the OLD one.
   • c. Deleting memory of a single command
     • A single deletion stage is needed for each memorized button.
       1. Press and hold down the RF-LEARN button (Figure 3) on the control board for 5 seconds.
       2. Wait until the LED display shows “DKY”, then, within three seconds:
       3. Press the button on the remote to be deleted. If the remote has been deleted, the LED display will flash quickly five times.
       4. Repeat the above steps if more buttons to be deleted.
   • d. Deleting all memory of all remotes
     • With this operation, all the memorized transmitters will be deleted.
       1. Press and hold down RF-LEARN button (Figure 4) on the control board for 10 seconds.
       2. Wait until the LED display shows “DAL”. (When you see DKY, keep pressing the RF-Learn till it shows DAL). All memory is deleted.
2. Step 2: System Learning
   • Step1: Press and Hold the Press SET button for 3s, When the LED shows “LEA” then release SET, then the motor runs the system learning procedure automatically, once learning completed shows “D-G” or “S-G” (No remote required)
     1. Note: Please check the parameter setting of “FI”(Dual/Single) before going into system learning.
   • Restore the system default setting
     • Press and Hold the UP + SET + DOWN button for 5s and the panel restores to default setting
     • Note:
       1. LED Shows “D-G” tells the system learning has been completed for Dual Gate installation
       2. LED Shows “S-G” tells the system learning has been completed for Single Gate installation
   • A. Dual Gate:
     • (1) Slave Gate Close » (2) Master Gate Close » (3) Master Gate Open
     • (4) Slave Gate Open » (5) Slave Gate Close » (6) Master Gate Close
   • B. Single Mode:
     1. Master Gate Close » (2) Master Gate Open » (3) Master Gate Close
        • For Single Gate installation, please make sure the motor cable connects to M1+/M1-, and the parameter to set function Fl-0 to the single gate, and also set FB-0 pedestrian mode to be function off, and once the system learning is completed, the LED will show S-G

Gate Operation Logic

• A. In the gateopening phase: The gates stop if the transmitter/push button/key selector is activated, and close when the transmitter/push button/key selector is reactivated.
• B. In the gateclosing phase: The gates stop if the transmitter/push button/key selector is activated, and open when the transmitter/push button/key selector is reactivated.

Safety For Gate Operation

• In the gate-opening phase: For safety purposes, the gates stop if encountering obstacles.
• In the gate-closing phase: For safety purposes, the gates reverse for 2 sec if encountering obstacles.

LED Indication

1. LED Lighting
   • Blue LED System Learning: The Blue LED in the receiver board blinks two times when learning is completed.
   • LED2 RF: The key selector or the push button is activated, and LED2 will be on.
   • LED4 Ph1: LED4 will be on when Ph1 is triggered.
   • LED3 Ph2: LED3 will be on when Ph2 is triggered.
2. The function of the LED display

Parameter Modification

Parameter Learning

1. Press “UP+SET” for 3 seconds to get into the program setting display from F1.
2. Press “UP” or “DOWN” to change setting item from F1 to FJ.
3. Press “SET” button again to get into the sub-settings.
4. Press “UP” or “DOWN” to change Push from F1-0 to F1-2.
5. Press “SET” button again to confirm.

Parameter

Note (F1-2 over-current setting in Hall sensor mode):

• Only in “F1-2” Hall sensor mode, the PCB will record all the current values in learning mode. Please adjust over current value by setting the F3 function after learning mode.
• The recorded current values will increase according to the value shown on the LED display over the current value.
• The value can be adjusted by pressing the button UP and DOWN. The maximum value is 50(5.0A) and the minimum value is 05(0.5A). LED display example:
  • Indicate 1.0 ampere: all of the recorded values will increase by 1 ampere over the current value.
  • Indicate 0.6 amperes: all of the recorded values will increase by 0.6 amperes over the current value.
  • Indicate 2.8 amperes: all of the recorded values will increase by 2.8 amperes over the current value.

Photocell Logic

FA-0 Photocell OPEN/CLOSE (Standard set up)

FA-1 Safety Edge

FA-2 Open Only Device (Vehicle detector)

FA-3 Double photocell set up

Troubleshooting

Technical Specification

FCC

FCC Warning

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirements.

Documents / Resources

TMT AUTOMATION CB19 Control Box For Hermit [pdf] User Manual 2BCSY-TM4, 2BCSYTM4, tm4, CB19 Control Box For Hermit, CB19, Control Box For Hermit, Hermit

References

• User Manual