Instruction Manual for VEVOR models including: MX24-111, MX24-111 Golf Cart Rear Seat Rack, Golf Cart Rear Seat Rack, Cart Rear Seat Rack, Rear Seat Rack, Seat Rack
GOLF CART REAR SEAT RACK MODEL:MX24-111 MODEL:MX24-111 GOLF CART REAR SEAT RACK This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product. 1 Assembly precautions 1. Assemble according to these instructions. Improper assembly can cre ate hazards. 2. Product capabilities apply to properly and completely assembled produc t only. 3. For additional information regarding the parts listed in the following pag es, please refer to the Assembly Diagram of this manual. Unwrap and se parate all parts in a clean work area. Please keep small spare parts out of children's reach. SAVE THESE INSTRUCTIONS WARNING: The product is not a toy, children shall not play with the product. Packing list Serial Number Name Quantity A Connecting Ear Plate 2 B Connecting Ear Plate Support Tube 2 C Turning Connector 2 D Lower Connecting Tube Assembly 1 E Upper Connecting Tube Assembly 1 2 Serial Number a b c d e f g Name Hexagon Head Bolt Hexagon Head Bolt Oversized Flat Washer Flat Washer Spring Washer Self - locking Nut Drum Brake Specification Quantity 1# 2# 3# M8×50 12 8 4 - M8×45 4 - - 4 M8 24 16 - 8 M8 8 - 8 - M8 4 - 4 - M8 16 8 4 4 25 3 2 - 2 - Serial Number Name Specification Quantity 1# 2# 3# h Single - ended Fixed Wrench M8S13 1 - 1 - For easier installation, pre-sort the components into 1#, 2#, 3#. Their quantities will be used in Steps 1-3. Installation Steps Step 1: Install the connecting lug support tube (B), the turning connector (C), and the lower connecting tube assembly (D) together using the 8 hexagon head bolts M8×50, 16 oversized flat washers M8, and 8 self - locking nuts M8 from Set 1#. 4 Step 2: Slip the brake caliper from Set 2# onto the lower connecting tube assembly (D). Insert the upper connecting tube assembly (E) into the lower connecting tube assembly (D), adjust it to the appropriate height, then rotate and tighten the brake caliper. 5 Step 3: Install the connecting lugs (A) together using 4 hexagon head bolts M8×45 and 4 oversized flat washers M8 from Set 3#. Step 4: Use 4 hexagon head bolts M8×50, 8 flat washers M8, 4 spring washers M8 and 4 self - locking nuts M8 from Set 2# to install the assembled connecting ear plates (A) and the footrest together. Step 5: Install the installed connecting lug support tube (B) and the footrest together using 4 oversized flat washers M8 and 4 self - locking nuts M8 from Set 3#. 6 Precautions Regularly check the installation status of the rear armrest. If it is loose, tighten it in a timely manner. Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD 7 NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting UK REP Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX E-CrossStu GmbH EC REP Mainzer Landstr.69, 60329 Frankfurt am Main. 8Microsoft: Print To PDF