One moment, please...One moment, please...One moment, please...One moment, please...
User Guide for MOTIONBLINDS models including: CM36B, ZY4CM36B, CM-36, CM-36 Curtain Blind Motor, Curtain Blind Motor, Blind Motor, Motor
Coulisse B.V. CM36B ZY4CM36B ZY4CM36B cm36b
File Info : application/pdf, 11 Pages, 1.32MB
DocumentDocumentMOTIONBLINDS MANUAL setup guide CURTAIN BLIND MOTOR CM-36 WARNING Read the instructions carefully before assembling and using the product. Assembly can be completed by non-professionals. For indoor use only. Young children can strangle themselves with the loop of pull cords, chains and tapes, and cords that operate window coverings. To avoid strangulation and entanglement, keep cords out of reach of young children. 2 Cords may ensnare a child's neck. Move beds, cots and furniture away from window covering cords. Do not tie cords together. Make sure cords do not twist together and form a loop. Cleaning Follow these general rules when cleaning the outside of the device and its components: Use a damp, soft, lint-free cloth. Avoid getting moisture in openings. Do not use aerosol sprays, solvents, alcohol, or abrasives. Service & Support Do not perform repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside. Warranty Service First follow the advice in this manual. If the product appears to be damaged or does not function properly, go to your local dealer for instructions on how to obtain warranty service. Recycle This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collec-tion systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Conforms to UL Std. 325 Certified to CSA Std. C22.2#247 Important Safety instructions WARNING: To reduce the risk of severe injury or death, it is important to follow these instructions for personal safety. Save these instructions. Important Installation instructions WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury. ENGLISH Read and follow all installation instructions. This motor can only be used with soft material This appliance can be used by children aged for driven parts. 8 years and above and persons with reduced Hazardous unprotected moving parts of the physical, sensory or mental capabilities or lack drive must be installed higher than 2.5m above of experience and knowledge if they have been the floor or any other level surface that could given supervision or instruction concerning use provide access to it. of the appliance in a safe way and understand Install the actuating member of a manual the hazards involved. Children should not release at a height less than 1.8m. play with the appliance. Cleaning and user The actuating member of a biased switch is to maintenance should not be performed by be located within direct sight of the driven part children without supervision. but away from moving parts. It is to be installed Do not allow children to play with fixed controls. at a minimum height of 1.5m and not accessible Keep remote controls away from children. to the public. Frequently examine the installation for The mass and the dimension of the driven part imbalance and signs of wear or damage to must be compatible with the rated torque and cables and springs. Do not use if repair or rated operating time. adjustment is necessary. Fixed controls have to be clearly visible after This instruction manual is also available on the installation. website. The driven part must be compatible with the The drive must be disconnected from its power rated torque (1.2N.m) and rated operating time source during cleaning, maintenance and when (12 min). 3 replacing parts. The drive is intended to be installed at a height The A-weighted emission sound pressure level of at least 2.5m above the floor or any other of the drive is equal to or less than 70dB(A). accessible level surface. Indoor and household use only. All-pole disconnection switches must be Disconnect the drive from the power supply incorporated in the fixed wiring in accordance or switch off the automatic controls when with the wiring rules. maintenance, such as window cleaning, is The appliance must only be supplied at safety being carried out in the vicinity. extra low voltage corresponding to the marking When operating a biased switch, make sure that on the appliance. other persons are kept away. Before installing the drive, remove any Do not operate when maintenance, such as unnecessary cords or components and disable window cleaning, is being carried out in the any equipment not needed for powered vicinity. operation. The tube motor must only be supplied with safety extra low voltage corresponding to the marking on the appliance. FCC Manual FCC ID: ZY4CM36B Regulatory Information 1 FCC Information for User This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. 2 FCC Electronic Emission Notices This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. 3 FCC Radio Frequency Interference statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits 4 are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct the interference at their own expense. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the distance separating the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. EU Declaration Hereby, Coulisse declares that the radio equipment type CM-36 is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.my.coulisse.com Frequency range: 433 MHz, RF power: 2.32 dBm Frequency range BLE: 2402 - 2480 MHz, RF power: 3 dBm EIRP Buttons and functions Reset/Program button LED (Reset indicator) MAC:2303 ENGLISH USB-C charging port LED (Battery indicator) 5 1 Install the blind Follow the steps in the installation instructions to install the blind. Curtain Motorized 4 x Inside mount Outside mount 6 2 Activate the blind To activate the blind, insert the battery into the motor. 1 2 3 Download the MotionBlinds bluetooth app Download the Motion Blinds bluetooth app from the App Store. ENGLISH App Store Download the MotionBlinds Bluetooth app rtube.nl/red1614 Google Play Download the MotionBlinds Bluetooth app rtube.nl/red1615 7 4 Setup the blind Open the MotionBlinds bluetooth app and tap the + sign. The app will now guide you through the setup process. The end positions of the blind, top and bottom, are pre-programmed. These can be adjusted in the app. MAC:2303 6 Adjustments Change end positions : If the blinds end positions are incorrect please open the settings of the blind and adjust the bottom / top position. 8 Pair a remote control .1 Select a channel on the remote and press the program button on the motor to activate program mode. The blind will start stepping up and down. CM-11 CM-12 CM-13 CM-15 CM-17 MAC:2303 Pair button Pair button Pair button .2 Press the pair button on the back of the remote control to pair the blind with the selected channel.The blind will shortly stop stepping, indicating that the remote has been paired to the blind. .3 Shortly press the program button to deactivate program mode. The blind stops stepping and can be operated. Operate the blind Center Channel Selection Up Down Remote control: Choose the channel to which the blind has been paired using the channel button. Press the up or down button to operate the blind. Press the center button to stop the blind. Use the left and right button to move the blind in small steps. Pull control: Pull once to move the blind to the end positions. 9 Pair with a bridge With the MotionBlinds bridge you can unlock more options, such as voice assistants and the ability to control your blinds when you are not at home. ENGLISH App Store Download the MotionBlinds Wi-Fi app rtube.nl/red981 Google Play Download the MotionBlinds Wi-Fi app rtube.nl/red982 Recharge the blind To charge the blind, connect it to a standard USB-C 5V power supply via a USB-C cable. This can be your iPhone's power adapter, for example. LED light flashes red; charge the battery LED light flashes green; battery is charging LED light constantly green; battery is fully charged 10 Reset the connection Hold the program button for 10 seconds to delete the connection between the blind and the app. The LED lights up 5 times and the blind steps up and down 1 time to indicate that the connection is reset. Now the blind can be reconnected. 5 x 10 s MAC:2303 Reset the blind Resetting the blind results in deleting the end positions and connections of the blind with apps and remote controls. Shortly press the program button to activate program mode. The blind will start stepping up and down.Hold the reset/program button for at least 20 seconds to reset the blind. The blind will stop stepping twice. After the second stop, the blind will give one extra step to indicate that is has been reset. ENGLISH Short press + MAC:2303 5 x 20 s MAC:2303 11 More information Please scan the QR code below to view the complete user manual with more information and advanced options. MOTIONBLINDS MANUAL USER MANUAL CURTAIN BLIND MOTOR CM-36 User Manual rtube.nl/red1673