Innovative Tech Solutions | Laser Corporation Australia
User Manual for LASER models including: WCALC-118, WCALC-118 Wireless Charging Clock Radio, Wireless Charging Clock Radio, Charging Clock Radio, Clock Radio, Radio
5 ore fa — Insert a USB flash drive or Micro SD card to switch to the TF mode, or press the button to switch. Aux Mode. 1. Connect the supplied 3.5mm audio cable into the ...
7 hours ago — To unpair (remove the connection entirely), go to the connected device's Bluetooth settings, find “SPK-WCALC-118” on the list of paired devices, and select “ ...
Laser Alarm Clock: Wireless Charging & Bluetooth Speaker
File Info : application/pdf, 15 Pages, 356.51KB
DocumentDocumentUser Manual Clock Radio with Wireless Charging SPK-WCALC-118 WHAT'S IN THE BOX · Clock radio · 240V Wall power charger · USB-A to USB-C charging cable · 3.5mm to 3.5mm audio cable · Clamp and screw (to secure the power cable) · User manual OVERVIEW 1. Mode 2. Clock 3. Alarm 4. Snooze / Brightness adjustment 5. Vol+ / Previous track 6. Vol- / Next track 7. Play / Pause 8. Bluetooth 9. TF (USB / Micro SD) 10. AUX 11. FM radio 12. Alarm 1 13. Alarm 2 14. Low battery 15. On/Off switch 16. USB-C port (Power) 17. USB-A port (Media) 18. Micro SD card slot 19. AUX port 20. Wireless charging area OPERATIONS Connecting to power 1. Connect the supplied USB-A to USB-C cable to the clock's USB-C port. 2. Connect the other end to the supplied 240V wall power charger. 3. Connect the charger to power. Wireless Charging · Place your phone on the wireless charging area of the clock. NOTE: The clock must be powered by the mains power for wireless charging to work. Set Time 1. Press the button to switch between 12/24- hour modes. 2. Hold down the button to start setting the time; the hour digit will start blinking. 3. Press the button to switch between hour/ minute settings. OPERATIONS continued... 4. Use and buttons to adjust the values. 5. Press and hold the button to save the time. Set Alarm 1. Press the button to switch between Alarm 1/ Alarm 2 modes. 2. While alarm icon is flashing on the screen, press and hold the button to start setting the alarm. 3. Press the button to switch between hour/ minute/On-Off/ringtone/volume/snooze duration settings. 4. Use and buttons to adjust values. 5. Press and hold the button to save the alarm. Alarm and snooze functions · Alarms are active when alarm symbols appear on the display. · While the alarm is ringing, press the Snooze button to activate snooze; press any other button to turn it off. OPERATIONS continued... · At other times, go through the alarm setting process to turn on/off the alarm. Switch Mode Press the button repeatedly to switch between Bluetooth /FM radio/Micro SD/USB/AUX modes. Adjust the display brightness Press the Snooze button to adjust the brightness between Off, Low, Medium and High. The default is High. Control the volume · Hold down the volume. · Hold down the volume. button to increase the button to decrease the Select previous/next song · Press the song. button to skip to the previous OPERATIONS continued... · Press the button to skip to the next song. FM Radio Mode · Press the button to switch to FM mode. · Long press the button to automatically scan and save radio stations. · Press and stations. buttons to select preset USB / Micro SD Mode Insert a USB flash drive or Micro SD card to switch to the TF mode, or press the button to switch. Aux Mode 1. Connect the supplied 3.5mm audio cable into the clock's AUX port and the headphone jack of the external device. 2. Press the button to switch to AUX mode. BLUETOOTH Pairing 1. Press the button to switch to Bluetooth mode. 2. Enable Bluetooth on your connecting device. It will search for nearby Bluetooth devices. 3. Select "SPK-WCALC-118". NOTE: If "SPK-WCALC-118" does not appear on your connecting device's screen, try again from the beginning of step 1. 4. Confirm Bluetooth pairing request on your connecting device. 5. Now, audio you play on your connected device should come through the clock's speakers. NOTE: The clock only connects to one device at a time. Use your device to control music playback and volume, or use , and buttons on the clock. BLUETOOTH continued... Answer/Hang up a call When there is an incoming call. Press the button to answer the call. Press again to end the call. Reject a call When there is an incoming call, hold down the button to reject the call. Disconnecting/Unpairing: · To disconnect, turn off the connected device's Bluetooth. · To unpair (remove the connection entirely), go to the connected device's Bluetooth settings, find "SPK-WCALC-118" on the list of paired devices, and select "Forget" or "Unpair". SECURE THE POWER CABLE Use the supplied clamp and screw to secure the power cable. 1. Run the supplied USB-A to USB-C cable through the clamp. 2. Plug in the cable to the clock's USB-C port. 3. Attach the cable to the clock by placing the screw through the clamp, into a recess, and tightening it. TROUBLESHOOTING Clock does not turn on · Make sure the On/Off switch at the back of the clock is in On position. · Press the Snooze / Brightness Adjustments button several times to increase the brightness of the display. · The built-in battery is completely discharged. Plug the clock to power. Wireless charging is not working · Make sure your phone supports wireless charging. · Make sure the clock is plugged into mains power using the supplied power adaptor and cable. · Make sure your phone is correctly aligned on the wireless charging area. · Remove any objects between your phone and the clock. · Restart your phone. TROUBLESHOOTING continued... No sound · The volume level is low or muted. Unmute or increase the volume. · If paired with a Bluetooth device, unmute or increase the volume level on the connected device. Cannot pair a Bluetooth device with the clock · The connecting device is out of range. Bring the device closer to the clock. · Make sure the clock is in Bluetooth mode. If not, press the button to switch to Bluetooth mode. · If the clock's Bluetooth name is not found on the Bluetooth list, refresh the list, or search again and wait up to 1 minute for the device to appear. · If the clock is already paired with another device, disconnect or unpair before connecting to the second device. SPECIFICATIONS Bluetooth version Wireless charging power Built-in battery Max. USB/Micro SD capacity Supported media formats in TF (USB/ Micro SD) mode Power adaptor Dimensions Weight 5.0 5 W / 7.5 W / 10 W 1,200 mAh 32 GB MP3 Input: AC 100-240V, 50/60Hz Output: 5VDC 3A, 9VDC 2A, 12VDC 1.5A 128(W)x108(D)x80(H) mm 442 g Thank you for your purchase! Laser Corporation is 100% Australian owned & operated. To get the most out of your product please read the user manual carefully and keep for future use. For specific information relating to your product such as Spare Parts, FAQs, Warranty claims, and more, please scan the following QR code: Visit our website www.laserco.com.au Check us out at www.youtube.com/lasercoau