Logo ng HoneywellThor VM1A Vehicle Mounted Computer
Gabay sa Gumagamit ng 

Sa labas ng kahon

Tiyaking naglalaman ang iyong kahon sa pagpapadala ng mga item na ito:

  • Thor VM1A vehicle-mounted computer (Model VM1A-LON)
  • Regulatory Sheet If you ordered additional accessories for your computer, verify that they are also included with the order. Be sure to keep the original packaging in case you need to return the computer for service.

Mga Tampok ng Computer

 

Honeywell Thor VM1A Vehicle Mounted ComputerHoneywell Thor VM1A Vehicle Mounted Computer - Fig

Mga Tampok ng pantalan

Honeywell Thor VM1A Vehicle Mounted Computer - Fig 1

Pamantayang pantalan

Honeywell Thor VM1A Vehicle Mounted Computer - Fig 2

Enhanced Dock

 

Honeywell Thor VM1A Vehicle Mounted Computer - Fig 3

Mount to Vehicle
The Thor VM1A should be secured to an area in the vehicle where it:

  • Does not obstruct the driver’s vision or safe vehicle operation.
  • Will be protected from rain or inclement weather.
  • Will be protected from extremely high concentrations of dust or wind-blown debris.
  •  Can be easily accessed by a user seated in the driver’s seat while the vehicle is not in operation. To mount the VM1A using a RAM mount system:
  1. Attach RAM base to a vehicle (RAM ball, RAM Clamp, RAM Plate, etc.)
    Honeywell Thor VM1A Vehicle Mounted Computer - Fig 4
  2. Attach RAM ball to the Smart Dock
    Honeywell Thor VM1A Vehicle Mounted Computer - Fig 5
  3. Ikabit ang VM1A na pagpupulong sa base ng RAM gamit ang RAM braso at higpitan ang hawakan ng pinto sa RAM braso.

Honeywell Thor VM1A Vehicle Mounted Computer - Fig 6

  • For more mounting details, refer to the user guide available at sps.honeywell.com.
    Connecting the Power Cable for 12-48 VDC Vehicles (10-60 VDC Direct Connection)
    tandaan: Refer to the Thor VM1A User Guide for other power connections, available at sps.honeywell.com.
    Pag-iingat: Para sa pag-install lamang ng mga bihasang tauhan ng serbisyo.
    Warning: Fuse Requirements For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead within 5 inches of the battery’s positive (+) terminal. The fused circuit requires a maximum time delay (slow blow) fuse with a current rating as noted below.
  •  Para sa 12VDC input, gumamit ng 10A mabagal na blow fuse na mayroong DC voltage rating greater than 12VDC
  • Para sa 24VDC input, gumamit ng 6A mabagal na blow fuse na mayroong DC voltage rating greater than 24VDC.
  • Para sa 36VDC input, gumamit ng 4A mabagal na blow fuse na mayroong DC voltage rating greater than 36VDC
  • Para sa 48VDC input, gumamit ng 3A mabagal na blow fuse na mayroong DC voltage rating greater than 48VDC.
    tandaan: For North America, a UL Listed fuse must be used.

Pagraruta ng Power CableHoneywell Thor VM1A Vehicle Mounted Computer - Fig 7

Ang Diagram ng Mga Kable ng Kable ng Kuryente na may Tamang Angle at 6 na mga Wires
Honeywell Thor VM1A Vehicle Mounted Computer - Fig 8I-twist ang pula at pula / puting mga wire nang magkasama at iikot ang itim at itim / puting mga wire nang magkasama bago kumonekta sa lakas ng sasakyan.
Connect the green wire to the vehicle ground:
Mag-ingat: For battery-powered vehicles, the green wire must be connected to the vehicle chassis ground.
Mag-ingat:  For internal combustion engine-powered vehicles, the green wire is connected to the vehicle chassis ground, which can also be battery negative.

Kulay ng Wire koneksyon
pula DC + (10-60 VDC)
Red / White DC + (10-60 VDC)
itim DC -
Black / White DC -
berde Lupa
Asul Ignition Sense Input (opsyonal)
Refer to the Thor VM1A User Guide, available at sps.honeywell.com, Para sa
further information about ignition control.

Sasakyan 10-60 VDC Direct Power Connection

  1. The VM1A must not be mounted in the dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock.
  2. While observing the Fuse Requirements, connect the power cable as close as possible to the actual battery terminals of the vehicle(if using unswitched power).
  3. Use proper electrical and mechanical fastening means for terminating the cable. Properly sized “crimp” type electrical terminals are an accepted method of termination. Select electrical connectors sized for use with 20AWG (0.81mm2) conductors.
  4. Sumangguni sa mga sumusunod na diagram ng mga kable para sa mga kulay ng kawad at koneksyon:
    • Ignition Control Wiring Diagram If switched vehicle power is available, the ignition wire can be connected. The VM1A will boot up when the vehicle ignition is turned on. Honeywell Thor VM1A Vehicle Mounted Computer - Fig 9• Ang Auto On Control at Manu-manong Kontrol ng Mga Diagram ng Mga Kable ng Ignition ay dapat iwanang naka-disconnect.
    Honeywell Thor VM1A Vehicle Mounted Computer - Fig 10Mag-ingat: For battery-powered vehicles: Red and red/white wire twisted together to battery positive. Black and black/white wire twisted together to battery negative. The green wire connected to the vehicle chassis ground.
    Mag-ingat: For internal combustion engine powered vehicles: Red and red/white wire twisted together to battery positive. Black and black/white wire twisted together to battery negative.  The green wire connected to the vehicle chassis ground can also be battery negative
  5. Route the cable the shortest way possible removing any leftover cable, and making sure the cable does not interfere with the safe operation and maintenance of the vehicle. The cable is rated for a maximum temperature of 221°F (105°C). The cable should be protected from surfaces that exceed this temperature, from physical damage from moving parts, and from chemicals or oil that cause the insulation to deteriorate. Avoid sharp bends. The power cable is less flexible in low-temperature environments
  6. Secure the cable to the vehicle structure at approximately one-foot intervals, taking care not to over-tighten, pinch conductors, or penetrate the insulation
  7. Connect the watertight connector end of the power cable to the dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely
  8. Secure the power cable to the VM1A using the strain relief cable clamps.
  9. Place VM1A in the dock
  10. If using the Screen Blanking feature, install the screen blanking box or switch. (Refer to the Thor VM1A User Guide, available at sps.honeywell.com, para sa karagdagang impormasyon tungkol sa kahon ng Blangko ng Screen.)
  11. Press the power switch on the back of the dock
  12. Press the power button on the front of the VM1A
  13. I-configure ang pag-uugali ng Auto-ON.

I-restart ang Computer

Maaaring kailanganin mong i-restart ang computer upang iwasto ang mga kundisyon kung saan huminto ang isang application sa pagtugon sa system o ang computer ay tila naka-lock.

  1. Pindutin nang matagal ang Power button hanggang lumitaw ang menu ng mga pagpipilian.
  2. Piliin ang I-restart.
    Upang i-restart ang computer kung ang touch panel display ay hindi tumutugon:
    • Pindutin nang matagal ang Power button nang humigit-kumulang 8 segundo hanggang sa mag-restart ang computer.

tandaan: Upang malaman ang tungkol sa mga advanced na pagpipilian sa pag-reset, tingnan ang gabay ng gumagamit.

Suporta

Pumunta sa sps.honeywell.com and select Support to search our knowledge base for a solution or to log into the Technical Support portal.
Dokumentasyon ng Gumagamit
Para sa gabay ng gumagamit at iba pang dokumentasyon, pumunta sa sps.honeywell.com.
Limitadong Warranty
Para sa impormasyon sa warranty, pumunta sa sps.honeywell.com and select Support > Warranties.
Patents
Para sa impormasyon ng patent, tingnan www.hsmpats.com.
Trademark
Ang Android ay isang trademark ng Google LLC.
Pagtatatuwa
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII. HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of software and/or hardware to achieve intended results. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII. Copyright © 2021 Honeywell International Inc. All rights reserved

Mga Dokumento / Mga Mapagkukunan

Honeywell Thor- VM1A Vehicle-Mounted Computer [pdf] Gabay sa Gumagamit
Thor-VM1A Vehicle-Mounted Computer, Vehicle-Mounted Computer, Mounted Computer

Mag-iwan ng komento

Ang iyong email address ay hindi nai-publish.