THE GIGRIG PLUS4 Remote Effects Loop Instruction Manual

THE-GIGRIG-LOGO

THE GIGRIG PLUS4 Remote Effects Loop

THE-GIGRIG-PLUS4-Remote-Effects-Loop-PRODUCT

Introduction

TheGigRig PLUS4 enables you to remotely switch up to 4 mono effects or 2 stereo effects via either TRS Remote Switches, MIDI or using TheGigRig RemoteX4 Footswitch. PLUS4 is a passive relay switcher with almost infinite headroom, so can be used for instrument or line level signal switching with zero signal loss. It is the ultimate performing, remote effects loop switching system.

Features

  • TRS, MIDI or RemoteX4 External Footswitch
  • 4 x Mono or 2 x Stereo operation
  • Relay based bypass with zero filtering
  • 2 separate parallel paths that can be linked or not
  • Integrated programable Pop Gate

Front Panel

THE-GIGRIG-PLUS4-Remote-Effects-Loop-FIG (1)

  • POWER LED Indicator
  • PLUS4 uses a standard 9V 2.1mm Centre Neg @ 200mA
  • MODE switch. Mode 1 keeps the switching of all 4 loops independent. Mode 2 switches loops 1&3 and 2&4 together via a single TRS for stereo operation
  • LINK button when pressed connects OUTPUT A to INPUT B giving you 4mono loops in series
  • LOOPS LED Indicate which loops are currently active. They also indicate which loops have the ‘pop’ gate activated. On power up the LEDs will flash once for pop gate inactive, twice for active

In Operation

The two rows of ¼” sockets on the back of PLUS4 are your 2 independent parallel signal paths. Path A is the top row, Path B the bottom row. Looking from the top, right to left is the input, then loop send and returns, then outputs. The LINK button on the front panel connects OUTPUT A to INPUT B.THE-GIGRIG-PLUS4-Remote-Effects-Loop-FIG (2)4 X MONO EFFECTS LOOPS

To use 4 mono loops, connect the effects in loops 1~4. By pressing the LINK button, OUT A will automatically be connected to INPUT B. Using INPUT A as your input, your signal with travel in series through loops 1~4, then out of OUT B.

2 X STEREO EFFECTS LOOPS

  • To use PLUS4 to switch 2 separate stereo effects, we will PLUS4’s parallel signal paths.
  • Connect your input signal, for MONO input choose INPUT A. For STEREO input use INPUT’s A&B.
  • PLUS4 send 1 to effect 1 MONO INPUT, PLUS4 return 1 from effect 1 MONO OUTPUT.
  • PLUS4 send 3 to effect 1 STEREO INPUT, PLUS4 return 3 from effect 1 STEREO OUTPUT.
  • PLUS4 send 2 to effect 2 MONO INPUT, PLUS4 return 2 from effect 2 MONO OUTPUT.
  • PLUS4 send 4 to effect 2 STEREO INPUT, PLUS4 return 4 from effect 2 STEREO OUTPUT.THE-GIGRIG-PLUS4-Remote-Effects-Loop-FIG (3)THE-GIGRIG-PLUS4-Remote-Effects-Loop-FIG (4)

RS Remote Switch Inputs

The GigRig PLUS4 has 2 separate TRS Remote Switch inputs for controlling the effects loops. The first set controls PLUS4 loops 1 & 2, the second set control loops 3 & 4. The Remote Switches operate using a latching switch. The dual TRS approach is perfect for anyone using a G2/G3 and wants to add 4 MONO effects at the start of their pedalboard using G2/G3’s Remote Switches. This gives you 4 more programmable loops per preset. Because the loops are completely passive and don’t use any filtering, they are ideal for impedance-sensitive effects such as fuzzes, germanium treble boosts, anything that doesn’t like buffers at the input.

MODE SWITCH – STEREO USE

  • If you are using stereo effects, the first stereo effect will use PLUS4 loops 1&3 in parallel, the second stereo effect will use PLUS4 loops 2&4 in parallel. By pressing the MODE switch, you only need to use one Remote Switch Input to switch your stereo effects.THE-GIGRIG-PLUS4-Remote-Effects-Loop-FIG (5)

MIDI

PLUS4 is fully MIDI programmable using both PC and CC messages. Connect your MIDI controller such as G3S or G3S Atom to the MIDI INPUT. All MIDI messages received are passed directly through to the MIDI OUT.

MIDI CHANNEL

The MIDI channel of the Interface is set by the rotary switch 1~9 selects channels 1~9, A~F selects MIDI channels 10~15

CONTROL CHANGE MESSAGES

  • LOOP 1 CC 80 – VALUE 64 to 127 ON, 1 TO 63 OFF
  • LOOP 2 CC 81 – VALUE 64 to 127 ON, 1 to 63 OFF
  • LOOP 3 CC 82 – VALUE 64 to 127 ON, 1 TO 63 OFF
  • LOOP 4 CC 83 – VALUE 64 to 127 ON, 1 to 63 OFF
    • All Off CC 121: This deactivates all input channels of the Interface

PROGRAM CHANGE MESSAGES

  • PC 1: LOOP 1 and deactivates the other LOOPS
  • PC 2: LOOP 2 and deactivates the other LOOPS
  • PC 3: LOOP 3 and deactivates the other LOOPS
  • PC 4: LOOP 4 and deactivates the other LOOPS
  • PC 5: This deactivates all active loops

PC Messages 10 to 25: This activates or deactivates each input channel according to the following pattern:

  • 10: 1 = inactive, 2 = inactive, 3 = inactive, 4 = inactive
  • 11: 1 = active, 2 = inactive, 3 = inactive, 4 = inactive
  • 12: 1 = inactive, 2 = active, 3 = inactive, 4 = inactive
  • 13: 1 = active, 2 = active, 3 = inactive, 4 = inactive
  • 14: 1 = inactive, 2 = inactive, 3 = active, 4 = inactive
  • 15: 1 = active, 2 = inactive, 3 = active, 4 = inactive
  • 16: 1 = inactive, 2 = active, 3 = active, 4 = inactive
  • 17: 1 = active, 2 = active, 3 = active, 4 = inactive
  • 18: 1 = inactive, 2 = inactive, 3 = inactive, 4 = active
  • 19: 1 = active, 2 = inactive, 3 = inactive, 4 = active
  • 20: 1 = inactive, 2 = active, 3 = inactive, 4 = active
  • 21: 1 = active, 2 = active, 3 = inactive, 4 = active
  • 22: 1 = inactive, 2 = inactive, 3 = active, 4 = active
  • 23: 1 = active, 2 = inactive, 3 = active, 4 = active
  • 24: 1 = inactive, 2 = active, 3 = active, 4 = active
  • 25: 1 = active, 2 = active, 3 = active, 4 = active

RemoteX4 Remote Footswitch

THE-GIGRIG-PLUS4-Remote-Effects-Loop-FIG (6)

The GigRig RemoteX4 is an external footswitch for use with a range of GigRig products, including PLUS4. Simply connect the RMT/MIDI OUT to the MIDI INPUT of PLUS4 using a 7 pin DIN cable provided with RemoteX4 and you’ll have instant control of PLUS4’s loops. Power is provided by PLUS4 via the 7 pin DIN cable so there’s no need to provide power to RemoteX4 separately.THE-GIGRIG-PLUS4-Remote-Effects-Loop-FIG (7)

POP Gate

PLUS4 features high-end audio relays with zero filtering. There is no AC coupling or DC restoration involved in any of our audio. In our 20 years + of experience, we’ve found that any filtering will colour the audio. It’s not inherently a bad thing, but there will be a difference between what goes in and what comes out, especially with impedance-sensitive effects such as vintage-style germanium fuzzes. One of the by-products of this is that any small amount of DC on the audio signal can sometimes present as a ‘pop’ when you switch effects in and out. In the large majority of cases this is filtered by the pedals own input and output capacitors. If per chance you have a pedal that you love the sound of but makes a pop when you switch, we have added a pop gate circuit which can be activated individually per loop. If the Pop Gate is off it is completely bypassed from the circuit. With it engaged it will provide an almost imperceptible ramp in of the effect loop.

NAGAGING POP GATE

  • Unplug the power
  • Unplug the PLUS4 A input
  • Using a latching switch in the Remote Switch Inputs, select the loop that you want to add Pop Gate to
  • Plug in the power with the loop selected

When you apply power to PLUS4 you’ll see the Effects Loop LED’s flash.

  • Flash once – Pop Gate disabled
  • Flash twice – Pop Gate enabled

To turn Pop Gate OFF simply repeat the process.

  • Pop Gate looks at INPUT A to see if it is unplugged or not. If its plugged, as would be the case 99% of the time after you’ve set up your rig, Pop Gate status will remain the same. The engaging or disengaging of Pop Gate only happens when INPUT A is unplugged.

Technical Specification

  • Input/Output Impedance: There are no active elements in the audio path. In and out impedances are dictated by the last active effects in the chain and the impedance at PLUS4 input when all loops are bypassed.
  • Bypass mode: True Bypass, Direct connection from guitar to amplifier/output.
  • Effects Loops: True Bypass, Direct connection between send and return. Pedals are muted when bypassed.
  • Bandwidth/etc: Studio Quality Bandwidth Flat frequency response.
  • Power: External power supply 9V 2.1mm centre negative minimum 200mA regulated
  • Current Draw: All outputs on, all LED’s on = approximately 100mA.

Dimensions:

  • Length: 12.5cm / 4.92”
  • Width: 9cm / 3.54”
  • Height 4.1cm / 1.61”
  • Weight: 0.34kg / 0.74Ib
    THE-GIGRIG-PLUS4-Remote-Effects-Loop-FIG (8)

Please note: All values are approximations. No responsibility will be taken for errors or omissions in the above specification. This specification is subject to change without notice. Please consult www.thegigrig.com for amendments

WARRANTY

The GigRig warrants this product to be free from defects in material and workmanship for 12 months (or legal standard for country of delivery) from the date of original purchase.If the product fails within the warranty period, The GigRig will repair or replace it at our discretion and cover return shipping. This warranty applies when used as recommended. It does not cover:

  • Loss, theft, misuse, abuse
  • Unauthorized modification or improper storage
  • Lightning or natural disasters

Damage from the above may incur a non-warranty repair fee. This warranty is not transferable to a new owner should you sell the pedal.

Legal:

In the event of a malfunction, the purchaser’s sole remedy is repair or replacement. The GigRig is not liable for:

  • Lost profits or savings
  • Damage to other equipment
  • Incidental or consequential damages

The GigRig’s liability will not exceed the original purchase price. All warranties other than those expressly stated are disclaimed.

Disposal:

  • No batteries or lead inside. Return to TheGigRig Ltd or follow local electrical disposal regulations.
  • Do not dispose of in household waste

Copyright & Legal

  • The GigRig is protected by copyright, patent, and design registration.
  • ‘GigRig’ is a registered trademark (No. 2343300).
  • Unauthorized copying of design or functionality for commercial gain may lead to legal action.
  • Licenses may be granted to non-competing companies.
  • RoHS Compliant
  • Compliant with EN 60950
  • Power supply approved for USA and EU regulations (see separate instructions)

Manufacturer:

  • The GigRig Ltd, Unit 15 Whitehill Industrial Pk, Royal Wootton Bassett, SN4 7DB

Authorised Representative:

  • EAS – Mustamäe tee 50, 10621 Tallinn, Estonia

Warnings:

  • For indoor use only. Keep away from water and children

Documents / Resources

PDF thumbnailPLUS4 Remote Effects Loop
Instruction Manual · PLUS4, PLUS4 Remote Effects Loop, Remote Effects Loop, Effects Loop

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.