เอกสาร
เนื้อหา ซ่อน

MANLEY SLAM Stereo Limiter และคู่มือการใช้งาน Micpre

บทนำ

ขอบคุณ!…

for choosing the Manley สแลม!. This unit combines Mic and Instrument Preamps, ลิมิตเตอร์ 4 ตัวและการวัดแสงที่ครอบคลุม อย่างที่คาดไว้ การดำเนินการพื้นฐานนั้นค่อนข้างง่ายและไม่จำเป็นต้องใช้คำแนะนำ – แต่ SLAM! มีคุณสมบัติขั้นสูงมากมาย และเราขอแนะนำอย่างยิ่งให้อ่านคู่มือนี้ มีเทคนิคและคุณสมบัติมากมายที่ไม่ชัดเจนนัก

In truth, the SLAM! started with the idea of an updated Electro-Optical Limiter and the original working name was ELOP II. That didn’t last long. First we developed a fast FET limiter, decided that fast LED metering was appropri- ate, then added a mic pre, decided that this box would make the ideal “analog insert in a digital world”, then added almost every request and suggestion the customers had given us over the years. And somewhere during all this, decided each little part had to be right, and much was going to be quite new and elaborate. In the end, ELOP II was not at all descriptive and after a ‘name this box’ contest on our webเว็บไซต์มันกลายเป็น SLAM!.

เราสามารถเริ่มต้นได้ทันทีที่วงจรหลอดพื้นฐาน การออกแบบเหล่านี้ไม่เหมือนกับรุ่นอื่นๆ ที่เรารู้จัก รวมถึงวงจรของ Manley รุ่นก่อนๆ ดังนั้นนี่ไม่ใช่กล่องที่มีไมโครโฟนแบบเก่ารวมกับ Opto Limiter แบบเก่าและตัวจำกัด FET ที่ยืมมา ทั้งหมดนี้เป็นสิ่งใหม่ วงจรหลอดเป็นแบบไฮบริด FET/ การออกแบบหลอดที่ใช้ครั้งแรกใน Manley Steelhead phono preamp และให้ advantagของทั้งสองเทคโนโลยี คุณจะได้เสียง FET ที่เบา ส่วนหัวของท่อ ค่าเกนของทั้งสองค่าและการบิดเบือนที่ต่ำกว่าปกติ และพื้นผิวใหม่ในชุดเครื่องมือของคุณ

This is the beginning of the story and continues through the product and the manual. Some manuals seem to imply that if you use ‘this box’ then you are an instant mastering engineer or top producer with all the tools they use. This strange manual is filled with warnings, caution flags, grumblings about some aspects of digital and has extended quo- tations from other manufacturers. Our intention is to help the user, supply a bit of under-reported info, and give equal time to both what might help provide the sound you’ve been looking for and what might be considered questionable or dangerous to your music. The SLAM!, like other powerful processors, can be great or horrible depending on how it is used or abused and if something here helps avoid disasters, then we have happy customers.

GENERAL NOTES LOCATION & VENTILATION

The Manley SLAM! must be installed in a stable location with ampการระบายอากาศ ขอแนะนำว่า หากยูนิตนี้ติดตั้งบนชั้นวาง คุณควรเว้นระยะห่างที่ด้านบนของยูนิตเพียงพอ เพื่อให้อากาศไหลเวียนผ่านรูระบายอากาศได้อย่างต่อเนื่อง กระแสลมส่วนใหญ่ไหลผ่านช่องระบายอากาศที่แผงด้านล่างและออกทางด้านบน

You should also not mount the SLAM! where there is likely to be strong magnetic fields such as directly over or un- der power amplifiers หรืออุปกรณ์ที่ใช้พลังงานมาก ค่าฟิวส์ของเกียร์อื่นๆ มีแนวโน้มที่จะบอกใบ้ว่าดึงพลังงานหลักหรือไม่ และมีแนวโน้มที่จะสร้างสนามแม่เหล็กที่ใหญ่ขึ้น สนามแม่เหล็กอาจทำให้เกิดเสียงฮัมใน SLAM! และบางครั้งคุณอาจต้องทดลองจัดวางในชั้นวางเพื่อขจัดเสียงฮัม ในสถานการณ์ส่วนใหญ่ควรเงียบและปราศจากปัญหา

เราขอแนะนำให้คุณทำความคุ้นเคยกับสวิตช์และแจ็คที่แผงด้านหลังก่อนที่จะติดตั้งในชั้นวาง หากคุณมีตัวเลือกดิจิทัล ให้ทดลองกับการตั้งค่าตัวกรอง ปรับสี ฯลฯ เพื่อค้นหาการตั้งค่าที่คุณชื่นชอบ จากนั้นจึงจัดวาง

น้ำและความชื้น

As with any electrical equipment, this equipment should not be used near water or moisture. Beer is OK though.

บริการ

The user should not attempt to service this unit beyond that described in the owner’s manual.
Refer all servicing to your dealer or Manley Laboratories. Our service department is available for questions by phone (909) 627-4256 x325 and online at <www.manley.com/service.php>. Fill in your warranty card! Check the manual – your question is probably anticipated and answered within these pages…RTFM

พื้นที่ สวิสเซอร์แลนด์ กองทัพมีด

The SLAM! is an unusual product that doesn’t quite fit into a simple category. We get questions like “Why have a mic-pre on a limiter?”, and “Why so many input and output jacks?” and “Why no hard-wire bypass on this mastering processor?”. And the only answer is “It’s not just a………….. , it does a lot more”. It isn’t a channel strip – no EQ, besides

being stereo. It isn’t just another front-end for the workstation. It isn’t just a mastering processor. Maybe the SLAM! is a new category.

 

สแลม! เป็นลิมิตเตอร์สำหรับเรือนอกและไมโครโฟนแบบหลอดกำลังขยายสูงที่มีสัญญาณรบกวนต่ำแบบใหม่ โปรเซสเซอร์ควบคุม และ DI ในฐานะที่เป็นไมค์พรี ให้อัตราขยายประมาณ 70 เดซิเบลและวงจรใหม่ ต่างจาก Manley Pre . รุ่นก่อนๆamp. กำไร stages ขึ้นอยู่กับวงจรที่พัฒนาโดย Mitch Margolis สำหรับ Steelhead phono preamp. สแลม! สามารถใช้เป็นตัวประมวลผลหลัก (ไม่ใช่ตัวจำกัดหลายแบนด์) ซึ่งเป็นโปรเซสเซอร์ที่วิศวกรควบคุมหลักตัวจริงใช้ในการสร้างความดังโดยไม่ทำให้มิกซ์สับสน ในฐานะที่เป็น DI หรือ Instrument Input มันมี 2 อิมพีแดนซ์ (100K และ 10 Meg ohms) เกนมากมาย จำกัด และถ้าคุณต้องการความสนุกสนาน ใช้ทั้งสองช่องโดยใส่ EQ ที่ชอบระหว่าง...

ร้านแรกแรก

เรามีคำแนะนำง่ายๆ เพียงไม่กี่ข้อสำหรับวันแรกของคุณกับ SLAM!

  • Don’t rack mount it until you are familiar with the back panel and have experimented a bit with the jacks and switches that you might use No problem racking it, but this way is easier at first.
  • Watch those levels. There is a lot of gain and ways to manipulate gain on the SLAM!. We have seen guys set up 30 dB of boost to a line signal, 30 dB of limiting and were not aware of how drastic those settings might be because they were unfamiliar with the box. On he LED meters, one segment = 1 dB (approximately), and if you see the LEDS go half way down, you are hitting 13 dB of limiting which is generally drastic. Most engineers prefer 6 dB or less limiting. You need to use your ears, and your eyes. Common mistake.
  1. Unity gain for line inputs is near 12:00 for the INPUT and OUTPUT Begin with the ELOP and FET thresholds fully clockwise (5 o’clock). A good starting point.
  2. To set INPUT levels start with the VU on INPUT and the VU attenuator at the “0dB” especially as you become familiar with the SLAM!. You have to be aware that practically all the knobs and switches affect level and gain and that you want to start off on the right foot, so get the INPUT set first. Then set Thresholds and Output level. Most early confusion has been due to level settings.
  3. The LED PEAK METER (audio mode) is most useful to view เมื่อตั้งค่าลิมิตเตอร์และเปรียบเทียบว่าจะดังได้แค่ไหนเมื่อถึงระดับสูงสุดเดียวกัน เปรียบเทียบระดับสูงสุดเดิมของคุณใน Bypass กับระดับที่เป็นไปได้ด้วยการจำกัดการทำงาน
  • This is a limiter and limiters generally can create weird distor- tions especially when the gain reduction is deep and releases
    are fast. The SLAM! FET limiter has very fast releases so it can be dangerous. The OPTO is easier to use because the attack & release are slower which is why opto’s have always been popular. Sometimes we want the ease of opto and the speed of FET, and using the FET gently to ‘clean up’ the overshoots of the opto is pretty easy too. With the FET limiter alone, some experimenta- tion and critical listening is a must. Different songs and sounds seem to want different settings and one may often be surprised by the optimum setting.
  • Because the SLAM! is old-school analog, the limiters won’t have the ‘precision’ of a digital limiter that can be easily set to hold peaks within 0.1 or 0.2 dB of clipping. If you intend to use it as a brick wall limiter before the A to D converter as a method to be safe/lazy/ clever, in an attempt to get hot levels within .2 dB of digital clipping you may be creating the worst case scenario for an analog It is difficult to set the SLAM! up to do that. It can be pretty good IF you take the time to carefully set the controls. Foolproof and easy – no, but if you want ‘easy’, then the safest way is to accept -2 to -5 dB DFS (23+ bits), and use a digital limiter like an L1 or L2 for the last few dBs. The combination provides the best of both worlds. Another approach is to try the “CLIP” setting plus the OPTO which is a bit easier and may or may not be as audible. It might not be worth being obsessed with hitting -.1 dB DFS and focus on the sound instead.
  • Once you have found your favorite back panel settings, feel free to rack mount the SLAM!. Yes, you can leave Phantom on all the time. Old consoles didn’t have phantom switches and it was always on – no problem.
  • POWER MULTI-PIN: 16 PIN AMP connector that screws into the matching socket on the back of the SLAM!. This should be connected first. Rotate the whole connector until it mates with the socket, then just a turn or so on the outer ring clockwise will complete the Force will NOT be needed. The cable is 6 feet long and keeping the supply
    6-12” away from other gear reduces the possibility of induced hum, though this supply won’t radiate much. The supply may get reasonably warm, and this is an intentional trade-off to keep those magnetic fields minimal.
    NOTE: The bulk of the power supply will not turn on (including the LED) unless this connector is inserted, because the SLAM! remote controls the power for most of the Power Supply Unit.
  • IEC POWER SOCKET: Use the supplied IEC cable to connect the Power Supply Unit to wall This supplied cable should be the proper type for your country.
  • POWER TOGGLE: “ON” is marked. Note that BOTH this toggle has to be in the ‘ON’ position and the SLAM! front panel red ‘POWER’ button has to be pushed to turn on the SLAM!.
  • FUSE: The fuse protects you and the SLAM! in case of a catastrophe. Replace only with the same value and type. Failure to do so voids the warrantee. For 117 volts AC mains this fuse is a 2 Amp standard 1/4” SLO-BLO MDL 2. For 220 volts AC mains this fuse is a 1 Amp standard 1/4” SLO-BLO MDL A blown fuse often looks ‘blackened’.
    Several blown fuses indicates a problem needing repair. Both the Supply and SLAM! should be returned to the dealer or Manley Labs for service if the correct value fuses continue to blow.
  • VOLTAGสวิตช์เปลี่ยน E ควรตั้งค่าเป็น vol . ที่เหมาะสมtage for you country by the factory. The switch is marked, and in general a good habit to verify this setting is correct before plugging any new gear in and turning it The carton the SLAM! arrives in will also be marked for 117 or 220.
    ในกรณีที่คุณสงสัยเกี่ยวกับที่จับ ก็คือการปกป้องสวิตช์และฟิวส์ทางกลไก สกรูยึด 4 ตัวช่วยให้สามารถติดตั้งอุปกรณ์จ่ายไฟในชั้นวางหรือขันสกรูเข้ากับบางสิ่งบางอย่างได้

This is just a description of the various jacks and switches on the back. We suggest that you might want to not rack-mount the SLAM! until you’ve spent some time becoming familiar with the various patching and switches. Sorry, but the back panel is more complex than most gear and there are options galore. That’s what happens when you get what everybody asks for.
For simple maps that show a few exampวิธีแก้ไข SLAM! โปรดดูที่หน้า

  • ขั้วต่อเพาเวอร์. First verify the POWER SWITCH on the front panel is off (out) and Outboard Power Supply is off (tog- gle towards FUSE). The Outboard Power Supply has a captive 6 foot cable, with the mating plug. There is a painted white dot on the plug that should face UP and/or gently rotate it to find the “key” or where it fits. Force is definitely not needed. Rotate the ring on the front of the connector CLOCKWISE about 1 turn, which locks the connector in place.
    The SLAM! uses a trickle of power to remote control the power of the main supply. This means the Outboard Power Supply can not be turned on without it being connected to the SLAM!. This is a safety feature. Also, with that exception and the +&-6 volt supply used for tube filaments (heaters) all other pins are protected from passing current or a charge stored on power supply capacitors. In other words,
    it’s pretty safe, and that you can’t get a shock, and can’t power it up hot but still better to have both power switches off to connect this plug.
  • CHANNEL 1 INPUT. This is a Neutrik Combo jack that accepts XLRs, 1/4” mono phone plugs, 1/4” balanced phone This is both the LINE INPUT and the MIC INPUT. Phantom Power (6) is not advised except for some MICs, and in particular FET condenser mics and some rare exceptions that require it. If Phantom is ON, turn it off before patching into this jack (or any other mic patching) or at least turn the monitors, headphones, etc., down because there will be a loud speaker killing POP. Contrary to urban myth, it is highly unlikely Phantom Power will damage any mic or cause it to sound different, except during patching. It is a good
    idea, not to have Phantom on for LINE inputs, as it might be possible to damage something with the 48 volts if you select MIC (which can enable phantom).
  • CHANNEL 1 OUTPUT. This is a transformer floating balanced +4 dBu output (Pin 2 hot). It is equally happy feeding balanced or unbalanced inputs but for unbalanced inputs, be sure that the XLR’s Pin 3 is grounded or connected to Pin 1 or the There is also a transformerless unbalanced 1/4” phone jack output described below (5).
  • INSTRUMENT This is a 1/4” mono unbalanced high Z input for guitars, basses, synths, etc. It has about 30 dB more gain than the Combo jack input and uses the mic-pre. The input impedance is 100K suitable for synths and guitar processors/amp simula- tors but might be a bit dull for some guitars direct. For very high Z (10 Meg Ohm) physically insert the jack half way. Cool trick, huh? This will sound brighter for many guitars and basses, but should have little or no effect if any electronics are between the guitar and input.
  • CHANNEL 1 UNBALANCED OUTPUT. This jack provides an unbalanced +4 dBu output pre-transformer. It can also provide a semi-pro or consumer -10 dBv with plug inserted half way.

คำถามที่พบบ่อย - Why no -10 input when you provide a -10 output? There is no dedicated -10 dBu input but both the Combo jack (2) and Instrument Input (3) can be used in conjunction with the INPUT knob. Why share the same XLR for both MIC and LINE and no Phantom Switch on the front? It was origi- nally, but we added the HP filter on that switch, and felt it was ‘safer’ for your speakers to have the phantom on the back (see item 17).
Why no separate MIC-PRE output? 3 reasons, the mic-pre would require a good line driver (no more space for more tubes), the opto limiter works between both ‘sections’, and the Combo jack is used by both mic and line. In other words, it required 4 more XLRs and 2 tubes for this box and there is no room. 2 channels & 24 jacks plus 6 switches already, and gotta draw the damn line somewhere. Why use bantam jacks for side-chain inserts? (see P.8)

  • PHANTOM POWER SWITCH: This simply turns on 48 regulated volts of phantom power that ‘rides’ on Pin 2&3 of the BALANCED XLR INPUT. In this case, it is also only ON when you select one of the 3 Mic modes on the SOURCE

However, we do have several warnings:

  1. Because you can and will have a typical line input often plugged into that XLR and because you can easily switch to MIC, and because there is a chance some gear is not designed with DC blocking capacitors (or they are rated for less than 48 volts) there is a chance of doing damage to line level gear by ‘accident’. We don’t know of this ever happening but can imagine that it is possible.
  2. In general, patching mics with phantom turned on is a habit to break. Mic signals are typically 1/100th of a volt, and phantom is 48volts so rather huge speaker killing pops are likely – unless monitors, headphones, etc., are turned way down or off. c) For the same reason as above, running mics through patchbays, intermittent cables and corroded XLRs with phantom turned on may be extra noisy and crackly. If you need phantom, you need good solid connections. The only mics that need phantom are most FET condenser mics, and some other internally preamplified mics and a few DI We don’t know of any dynamic mics or tube condenser mics that require phantom.
  3. d) Contrary to urban myth, we also don’t know of any mic that can be damaged by phantom, whether it needs it or not, except a few ‘modified’ vintage ribbon mics that had their protective capacitors Early Neve and Trident consoles applied phantom power to every mic jack and offered no switch to turn it off. It is probably also a myth that some mics sound better with phantom off, but not a myth that bad jacks and cables will sound better with it off. Use phantom power only if its needed.

 

  • ขั้วต่อกราวด์: These provide separate grounds for use in some installations, with special star grounds or other grounding techniques to prevent hum. In most situations the two terminals are simply connected with a wire. The top terminal marked CHASSIS is the AC third pin MAINS ground which also connects to the chassis’s, rack rails and can

internally connect to XLR pin 1. The bottom terminal marked CIRCUIT is the internal audio ground, which also connects to the 1/4” jacks sleeves.

 

  • SIDE-CHAIN INSERTS AND LINKING. These are all regular Bantam jacks, like are used in most patch-bays. Why these? Again size, space and they offer true, no-BS inserts like a patch-bay does. Most studios have Bantam to XLR adapter cables (we used to chop long patch cables in half and solder on XLRs) and if they don’t, they should. All of the outputs are impedance balanced (30 ohms), single ended +4 dBu The inputs are single ended, high Z, with the ring connected to ground through a 30 ohm resistor and should be compatible with most pro gear, balanced or unbalanced.

 

วิศวกรบางคนชอบที่จะต่อ EQ เข้ากับโซ่ด้านข้างของคอมเพรสเซอร์หรือลิมิตเตอร์บางตัวซึ่งจะเปลี่ยนแปลงการตอบสนองของลิมิตเตอร์ สำหรับอดีตample if the EQ is set to boost at 6K (or HP filtered at 3K), the limiter becomes more of a De-esser. Some dynamic controllers seem to be extra sensitive to low frequencies and bass, so we filter out low frequencies to prevent excessive pumping or squashing on bass heavy material. A text-book limiter would not have side-chain inserts because it is supposed to accurately limit true signal peaks. The SLAM!’s Opto Limiter has a switch that provides some side-chain low freq filtering at 100 and 200 Hz. The 200 Hz setting also boosts about 4 dB at 6K, for a bit of gentle de-essing to be the “vo- cal setting”.

เนื่องจากในกล่องมีลิมิตเตอร์ 4 อัน เม็ดมีดโซ่ด้านข้างจึงต้องใช้แจ็ค 8 อัน (ส่งและคืน) แจ็คตัวบนสองตัวส่งสำหรับตัวจำกัด Opto (L&R) และพวกมันจะถูกปรับให้เป็นปกติครึ่งหนึ่งเพื่อส่งคืนสองตัวที่อยู่ด้านล่าง บางคนอาจใช้สิ่งเหล่านี้เป็นทางเลือกนอกเหนือจาก MIC PRE แต่ Opto Limiter และ FET Limiter จะส่งผลกระทบต่อพวกเขาในระดับที่น้อยกว่า แต่จะหลีกเลี่ยงหลอดสุดท้ายtagES

แจ็ค 4 ตัวถัดไปนั้นใช้สำหรับ FET Limiter ในทำนองเดียวกัน การส่งเป็นการดำเนินการamp isolated version of the unbalanced main output. Any plug or patch cord in any of the ‘returns’ breaks the normal and unless there is a healthy +4 dBu signal inserted there, you won’t see any limiting.

The jacks marked EXT LINK (5.1) are just intended for those lucky guys with 3 SLAM!s who need a way to link 5 or 6 lim- iters for surround work. Two regular Bantom patch cables are required. These jacks are paralleled, and the rings carries the Opto audio link, the tip carries the FET DC link. The LINK toggle on the front panel must be in the BOTH & EXT position and all controls on all 3 units are used. The Opto Link blends all 6, the FET link uses the moment-to-moment highest signal of the 6 channels.
The bottom two jacks are unused at present, but might be useful for mods and special versions. We had an idea to use them for a ‘blend’ input because some guys like to use the drum sub-mix to ‘push’ the 2 buss limiters, but we felt this was a bit excessive and can be done with the above side-chain inserts easily enough.

  • CHANNEL 2 อินพุตที่สมดุล: Similar to Channel 1 described by 2) above.
  • CHANNEL 2 เอาต์พุตที่สมดุล: Similar to Channel 1 described by 3) above.
  • CHANNEL 2 อินพุตเครื่องมือ: Similar to Channel 1 described by 4)
  • CHANNEL 2 UNBALANCED OUTPUT: Similar to Channel 1 described by 5) above.

แผงด้านหน้า

  1. แหล่งที่มา: This is the Input Selector that you use to choose the input to the SLAM!. The choices are LINE, DI, MIC, MIC ø (phase reverse), and MIC 100 HZ (high pass filter) which has a little graphic showing the LINE selects the BALANCED LINE INPUT Combo jack (XLR or 1/4”) and is intended for +4 dBu signals, but by cranking the INPUT level can be used with -10 dBv signals.
    DI selects the INSTRUMENT INPUT jack and routes it through the mic preamp for lots of gain if needed. MIC also uses the BAL- ANCED LINE Combo jack and routes it through the mic pre for 60 dB of gain (and another 20 dB by cranking the OUTPUT level). MIC ø is the same except opposite and just phase reversed (the proper term is polarity reversed). MIC 100 Hz is normal polarity but the lows below 100 hertz are filtered out which is useful on many vocals and overheads, to remove pops, air conditioning rumble, etc.
  2. อินพุต: This is the first volume control and has about 60 dB of range for MIC and DI, and from -20 to +20 for For LINE, the normal setting will be 12:00, or straight up, but this isn’t the rule or an absolute calibration. For MIC or DI, the knob might be anywhere depending on the mic, the loudness of the instrument, the distance, etc., and it might be prudent to turn the knob down to start, rather than starting at 12:00.
  3. เอาท์พุท: This is the final volume control and is used to set the output level to tape or disk, and as the ‘gain make-up’ after the Opto Limiter, if you need to compare ‘limit and bypass’. The FET Limiter senses the signal right at the output jack, so it acts as if it is a final limiter after the OUTPUT Circuit-wise the FET Limiter is directly after the Opto, and before the OUTPUT level (but doesn’t act like it) and before the final tube gain stage/ line driver. The range of this knob is about -20 dB to +20 dB with unity gain near 12:00. Most of the time it will live between 12:00 and 3:00.
  4. OPTO LIMITER: A simple threshold knob for the OPTO limiter. Fully clockwise (+26) is ‘out’ and a good place to start. As you turn this knob counter-clockwise, there is more likelihood that limiting will happen. Some dynamics units have the threshold go one way and some the On the SLAM!, all of the pots, should make the signal louder when turned clockwise, (except the RELEASE which is a switch).
  5. SC HZ: Side-Chain Hertz. This is a HP filter in the Opto Limiter side-chain that makes that limiter less sensitive to low frequen- It does not affect the FET Limiter. The filter helps minimise pumping and strange volume changes. Sometimes kick drums and bass seem to ‘trigger’ too much limiting. The FLAT setting, bypasses the filter, 100 filters 100 Hz by 6 dB and more for frequencies below that. Similarly 200 filters 200 Hz 6 dB and more below but also boosts about 4 dB at 6 kHz for gentle and subtle de-essing and can be considered a vocal setting. Normally, 2 filters like these require one to change the threshold significantly, but these are compen- sated to minimize that.
  6. FET LIMITER: Another simple threshold knob. One can blend any balance of Opto and FET limiters by using the two threshold Each limiter has its own character and advantages และเสริมซึ่งกันและกัน เพื่อว่าโดยการใช้ทั้งสองอย่าง จะได้รับ advan . ส่วนใหญ่tagโดยไม่มีข้อเสียtagอี สำหรับอดีตample, the Opto can limit deeply, smoothly and has a high ‘ratio’, but is a little slow for drums, while the FET Limiter can be very fast, but not as deep. The Opto has inherent time constants but the FET can be adjusted for attack and release times. What the Opto misses, the FET should catch, depending on how you blend them and the FET ATTACK time.
  7. จู่โจม: This just affects the FET Limiter. With compressors, ‘attack knobs’ are used to set how fast the compressor responds and pulls down a signal. Traditional limiters don’t have this because it compromises the ‘concept’ of limiting if there is any overshoot. We compromised somewhere between ‘text-book limiter’ and ‘typical compressor’, and simulated much of the ‘sound’ of the attack con- trol while still providing more transient reduction than is apparent. VF is very fast (.1 mS), F is fast (1mS) and M is moderate (10mS). VF is the best if you need to prevent ‘overs’ and is closest to the traditional or text-book limiter. F and M tend to let more transient through but are also more punchy and may be less detrimental to drums. Expect to adjust the FET LIMIT knob a bit for similar depths of reduction when you change ATTACK (typical). There is another side-chain that grabs much of the peaks, almost inaudibly, but our ears tend to hear the side-chain that has the ATTACK and RELEASE Use your ears to determine the best setting. Instruments with fast transients like drums show the biggest differences, vocals less so, and soft flute-like sounds may not be affected except for a little threshold difference.
  8. ปล่อย: This only affects the FET Limiter. There are 11 positions numbered from 2 Seconds (slowest), to 10 milliseconds (fastest). Slow releases tend to be the least audible and will be cleanest. Medium release times on the SLAM! are pretty fast for a lim- iter and where the most loudness increase tends to be, but if pushed too far also might be obvious with pumping or a volume rise after the ‘crescendo’. This may also be near the edge of when ‘modulation’ starts to become audible, especially if there is a lot of bass en- ergy in the signal. Achieving maximum loudness cleanly is not automatic and might require a bit of play between threshold(s) release time and attack because it really depends on the music. The SLAM! attempts to minimise all the negatives, pumping, modulation, loss of ‘energy’ that is typical for a limiter with fast attack and release times because this is where the maximum loudness lives – but – this is dancing on the edge of a dangerous cliff.
    สแลม! สามารถตั้งค่าเวลาปล่อยสำหรับการปล่อยอย่างรวดเร็วอย่างน่าขัน (10 & 25 mS) ซึ่งรับประกันความผิดเพี้ยนของการปรับเสียงต่ำได้มาก ซึ่งมักไม่พึงปรารถนา แต่สามารถใช้เป็นเอฟเฟกต์และแปรงทาสีอีกอันได้ เราอาจใช้ความระมัดระวังในการปล่อยเพลงที่เร็วเป็นพิเศษกับเครื่องดนตรีเบส แต่อาจเป็นเรื่องสนุกสำหรับกลองที่หยาบคายและโซโลที่ร้อนแรง นอกจากนี้ยังมีการตั้งค่า CLIP ซึ่งแนะนำปัตตาเลี่ยน FET ที่ค่อนข้างกลมเหมือนวงจรหลอดป้อนกลับต่ำบางตัว overdrive และชวนให้นึกถึงการบิดเบือนของลำโพงเล็กน้อย เราต้องการสร้างความทรงจำเกี่ยวกับเสียงที่ดัง และนี่คือวิธีหนึ่ง CLIP เหมาะที่สุดในการเสริมกีตาร์ที่บิดเบี้ยวปานกลาง ของซินธ์อ้วน ไม่ได้มีวัตถุประสงค์เพื่อแทนที่ Marshall หรือ .ของคุณ amp เครื่องจำลอง แต่มักใช้เพื่อขยายเพิ่มเติมอีกเล็กน้อย
  9. STEREO LINK: A 3 position toggle. The center position disables stereo linking and is labelled DUAL MONO. All of Manley’s previous limiter/compressors provide a LINK switch and both L&R controls have to be used for proper operation. Meanwhile, most other compressors just use the left side while the right side controls become useless. Enough people requested, for us to include this mode of LINKing. This is the STEREO LINK or up position. Both ways have advantages. The modern ‘left-side only’ is convenient, easy and can be clever especially on a plug-in. The problem is that almost all implementations mono the L&R, which means sounds that are hard right or left are 6 dB less likely to trigger limiting than sounds down the center, and anything out-of-phase won’t be seen by the limiter at all. We think a proper ‘mastering compressor’ is supposed to react to the peak waveform of both the left and right equally, or stop the same peaks that causes the A/D to clip. This is easy in digital, but in analog it requires the user to use both sides, and that the limiters react equally based on whichever side has the loudest peak. So the SLAM! also has that mode “BOTH & EXT” or the down position. This mode is also used for the back panel linking to other SLAM!s for surround projects. For recording instru- ments the STEREO LINK mode is fine but for serious mastering the BOTH & EXT mode is usually best. ***NOTE: No LINK of the CLIP functions, because why have one side clip the other?***
  10. LED (meter): This switch controls the LED bar graph In the center position is basically an PEAK display of the audio out- put. The upper position is basically to display GR (Gain Reduction, especially the FET Limiter). The down position is a momentary switch that RESETs the peak hold (clears the dot) and is used to select the LED meter MODE if held down for a few seconds. A full and complete description of the LED Meter is on page 12. Suffice it to say here that it does a lot.
  11. LIMIT LEFT: Push it in to engage both the OPTO Limiter and the FET Limiter and the OUTPUT level control and it lights up This is not a hard-wire bypass, nor can it be, on a Swiss Army Knife, that has multiple inputs and outputs, mic pre-amps ฯลฯ บายพาสฮาร์ดไวร์ในเวอร์ชันมาสเตอร์มีโอกาสมากกว่าเล็กน้อย
  12. พาวเวอร์: OK, we won’t do a 300 word description of a power switch this time. Push it, it lights RED, and turns on the bulk of the Outboard Power Supply, which has been on idle drawing almost zero current. (If it doesn’t, remember that there is also a power switch on the power supply that has to be turned on.) The VU meters should light up, and about 30 seconds later the MUTE relay disengages (to prevent tube warm-up thumps) and audio should be available or rising gently. This box has a long warm-up time but should be stable in a minute and very nice in 15 Power-down mutes immediately. This might be a concern in a live situation; plan accordingly.
    If you are not using it for 8 hours, you might as well turn it off to save power bills and tube life. There is a school of thought that suggests that the initial turn-on is the hardest on tubes, and shortens their life and to some degree that is true. From our experience, it all depends on the individual tube and some last 30 years and some 30 seconds. If you are concerned with tube life and down-time, re- pairs etc., buy a set of extra tubes and save yourself some panic when you least need it. Changing a tube is almost as easy as changing a light bulb and once the top cover is removed should take 20 seconds (compare that to a repair needing the ‘ol soldering iron)
  13. LIMIT RIGHT: Just like 11, but for Channel Push to engage limiting and the OUTPUT level.
  14. วุฒิการศึกษา: Selects the source for the VU meters. I/P (input) shows the level directly after the INPUT level pot and is a good place to set the MIC-PRE gain or rough out operating levels. O/P (output) shows the output level appearing on the output jacks. GR shows the OPTO Gain Reduction, but not the FET. Most Opto Limiters use a VU to display gain reduction. When the limiters are bypassed the VU drops to below -20 which is not intended to imply extra hard limiting. The Opto can also be displayed on the LED meters, with an expected increase in speed because the Vactrols in the Opto Limiter are faster than
    VU ATTENUATE: One can also pad the VU’s down by 3 or 6 dB which is especially useful if the client is in the room and eye- ing the VU needles pegged in the red. Mastering engineers need this because a final mix has a lower ratio of peak to average level, and probably lower again after mastering. The SLAM! will tend to do that too. For individual tracks, we expect the 0 or no pad to be the most common but it depends on the instrument and distorted guitars may few and moderate peaks, but some percussion has huge peaks. We suggest the 3 dB pad for most mastering, and allowing about 3-6 dB below digital full scale on the peak meters. Why? FIR filters usually need 1 dB to 2 dB of headroom, MPEG usually requires 4-6 dB, the mastering engineer needs some room to work. The 6 dB VU pad is a hint that maybe this is project is ‘hyper-compressed’, especially if is still bending far into the red. It is nice for CD playback though.

การวัด

สแลม! มีการวัดแสงที่ครอบคลุมมาก หากคุณข้ามส่วนนี้ คุณจะกลับมาที่นี่พร้อมกับปากกาเน้นข้อความสีเหลือง เมื่อคุณเริ่มใช้กล่องจริงๆ แล้ว
There are both LED bar graphs and standard VU meters, and each can show a variety of information. Before proceeding further, we should mention that any peak meters and VU meters should look different with music and that they are intended for different pur- poses. VU meters are deliberately slower, and are mostly intended to represent apparent loudness much like the way our ears work. LED peak meters are most often chosen when very fast peak read- ing signals need to be represented. For “standard” VU meters there is a long list of specs and qualifications, from needle size, color and ballistics to meter size, color and scaling. Most importantly, VUs have been around a long time and most engineers find them easiest to interpret and most valid for analog tape. Because peak meters are fast compared to VUs, transients like drums will look louder than on VUs, and this is a good thing if we are concerned with clipping or digital recording.

กราฟแท่ง LED มีหลายสี (8) หลายโหมด (4) และอเนกประสงค์ มิเตอร์ควบคุมโดยสวิตช์สลับ 3 ตำแหน่งที่มีป้ายกำกับว่า LED พร้อมด้วย MODE & RESET (ลง) PEAK (ตรงกลาง) และ GR (ขึ้น) ระหว่างการทำงานปกติ สวิตช์จะอยู่ที่ตำแหน่งกึ่งกลางหรือขึ้น และจะควบคุมการแสดงผลบนมาตรวัดตามโหมดที่เลือกในปัจจุบัน ตำแหน่งลงชั่วขณะ (สปริง) มีฟังก์ชันที่แตกต่างกันขึ้นอยู่กับโหมดการทำงานปัจจุบันและระยะเวลาที่สวิตช์ถูกกดค้างไว้

Holding the switch down for more than .5 seconds suspends nor- mal operation and enters the Mode Menu, indicated by a color- ful pulsing on the top 2 segments of the right meter. While in this menu, one of 4 Modes described below can be selected. The selected mode is shown by a lit segment surrounded by two oth- ers near the bottom of the right meter. You can scroll through the 4 modes by pushing the switch down again quickly (before it returns to ‘normal’). Once the desired mode is lit, you ‘confirm’ the choice by either waiting 2.5 seconds or once again pushing down the switch but longer than .5 seconds. Modes 1 and 2 are the normal display modes and normal operation resumes. Modes 3 and 4 are used to select options.

โหมด

โหมด 1) DUAL DISPLAY: (shows two things at once)
Peak Position (center): Displays audio as a green and amber bar from the bottom up. FET Gain reduction is simultaneously displayed as a red dot from the top down.
GR Position (up): Displays FET Gain Reduction as a Green bar from the top down and OPTO Gain reduction as an Orange dot from the top down.
The Peak Hold dot and the third bar color are not available in this ‘dual display’ mode

MODE 2) SINGLE DISPLAY:

PEAK Position (center): This is a typical peak meter with a peak hold dot. The bar is divided into 3 colors, Green, Amber & Red. GR Position (up): Displays the sum of FET and OPTO Gain Reduction (or the total limiting) from the top down. Both the limiters are added together which may look a lot more drastic than it sounds and some interpretation is required. It is most useful when minimal limiting is the goal.

MODE 3) COLOR CHANGE POINTS:

You can change where the audio peak meters change color from green to amber and from amber to red. This is an unusual feature of this meter and lets you ‘match’ the SLAM!’s peak meter to the meters on your digital recorder or work-station. The SLAM! meters are analog and your other meters are very likely pure digi- tal so exact segment for segment matching is unlikely. This just gives you a way to set color change points.
Select Mode 3 with the momentary toggle and the display will change so that the left meter is totally lit and the right meter is still in audio peak mode (for reference). Below the POWER button is a small hole and a trim pot lives behind it. A small screwdriver or tweaker is needed to adjust it. If the Mode Switch is in the center position, then you can adjust the point where green changes to amber. If the Mode switch is in the GR or up position, you can

change the amber to red point.

หากคุณไม่มีระยะในการตัดแต่ง ให้ออกจากโหมด 3 ปรับแต่งการตัดแต่งให้อยู่ตรงกลางโดยประมาณ จากนั้นกลับไปที่โหมด 3 และตั้งค่าจุดเปลี่ยนสีในตำแหน่งที่คุณต้องการ

MODE 4) PEAK HOLD MENU

This is just for the peak hold dots in Mode 2. The selection is displayed on the left LEDs.

  1. No peaks held (no dot) (indicated by the lower of the 3 left segments)
  2. Peaks held for 1 second (typical generic peak meter) (indicated by the middle of the 3 left segments)
  3. ‘Infinite’ Hold, stores the peak until you manually reset by a quick push down and release of the momentary toggle. This mode is handy when the SLAM! is behind you and you need to know after the fact, the loudest transient that went through. Unfortunately, it won’t hold a ADC clip

RESET

Each time a mode is changed, all settings are saved to non-vol- atile memory. If you find that you have ‘out moded’ yourself, or that the meter is looking goofy, the การตั้งค่าเริ่มต้นจากโรงงาน can be restored as follows. With power off, press and hold the LED Meter switch down, and turn the power on. The left meter will light 2 segments red, the right green, release the switch.
บางครั้ง Opto จะทำให้ส่วนติดอยู่เนื่องจาก opto GR ไม่ได้ช้าลง (แชร์จากโหมด VU meter GR) เพียงเปลี่ยนเป็น Peak แล้วย้อนกลับจะล้างส่วนต่างๆ หรือรอจนกว่าจุดสูงสุดที่ร้อนแรงถัดไปจะล้างให้คุณ

VU METERS

Two toggles are used for the VU meters. One is used to select whether the VUs display Input Level (after the Input Pot), Output Level, or the OPTO Limiter Gain Reduction. If in BYPASS the OPTO GR the meters drop out rather than sit on zero. A VU meter showing OPTO GR seems to be a bit of a standard and the time constants and ballistics are a good match, even if the VU does not show every drop of gain reduction. The LED meter also can dis- play Opto GR or the total gain reduction.

The second toggle is a pad or attenuator for the VUs in the Input or Output modes and has no effect on GR mode. The 3 position switch gives 0 (no attenuation and calibrated to +4dBu), -3 dB and

–6 dB. While it is very unusual to get an attenuator for VU meters on standard rack processors, it is a feature we have been building onto mastering consoles for many years. A regular VU meter would be continually pinned in the red without the attenuator (which may have a disturbing effect on some clients). There are several reasons for this, some pre-dating the trends of heavy squashing. Compare individual acoustic tracks at DFS, to a mix at DFS, and the mix will generally look hotter on the VUs. Mixes tend to have more average energy than individual tracks. Both mixing engineers and mastering engineers often (usually) compress a mix, which also increases the ratio of average to peak somewhat. For exampในการบันทึก อัตราส่วนสูงสุดต่อค่าเฉลี่ยโดยทั่วไปคือ 16 ถึง 20 dB แต่ในการควบคุม 14 dB หรือน้อยกว่า

The SLAM! is a Swiss Army Knife and is intended to be used for much more than just mixes and mastering. Because it can severely reduce the ratio of average to peak levels, and because most of us now reference levels to digital full scale (a peak reading), it follows that without the attenuator, the poor VUs would be ‘in the red’ much of their life. We caution that the –6 position can mislead one into a situation where the audio is really too hot, or too squashed. On mastering consoles, the most often used VU pad is –4dB (a hint).

การวัดแสงโดยทั่วไป

The VU meters and the SLAM! peak meters will never agree and maybe the SLAM! peak meters are a little ‘off’ from the peak me- ters on an external ADC or DAC. What is going on? Which ones do I trust? How can I calibrate them to look the same?

These questions have been around for as long as there have been meters. VUs should match well with other VUs because there is a comprehensive list of standards and qualifications to meet to be a true VU meter. Part of the specification are ‘dynamic characteris- tics’ which describes “The pointer shall reach 99 on the percent scale on 0.3 second, overshoot less than 1.5% (.15dB)”. This es- sentially makes the VU meter act with “approximate RMS” re- sponse and our ears have an “approximate RMS response”. Ahh- hhh loudness.

Peak Meters are much faster and are supposed to catch events less than 0.0001 Sec (compared to the VU’s 0.3 Sec) which means that transients have a much bigger influence on peak meters. One prob- lem is that our eyes won’t be able to adequately see a 0.1 mSec flash or even 1 or 10 mSec so the designer has to stretch the dura- tion of the LEDs or pointer. In a sense, this exaggerates transient contribution, but at least looks good. There can also be a peak hold dot that adds a digital stretch to the duration and allows us the luxury of blinking or looking away once in a while. We have that in mode 2.

In pro audio there are few measurement standards (or even de-facto standards) that exist and peak meter calibrations and digital con- verter I/O levels are more prime examples. With digital peak me- ters that are married to digital converters, one at least expects that an ‘over’ in the A to D over would light the top red LED. Wrong – the better meters use 4 sampน้อยกว่าและดีที่สุดอนุญาตให้ผู้ใช้ตั้งค่าหมายเลขนั้น 4 วินาทีamples over เป็นเรื่องเกี่ยวกับธรณีประตูที่เราได้ยินคลิป สมเหตุสมผลกับฉัน

The SLAM! LED meter is not digital, it is an analog meter with a micro-processor. It can be adjusted for different analog sensitivities with an internal trim pot, but this is not guaranteed to ‘match’ other peak meters, nor was it intended to. The SLAM displays approxi- mately 1 dB per segment, except near the bottom which are much bigger steps to show signal present. Other meters may show 2 dB or 1/2 dB steps or be dB scaled on a curve.

โซลูชันของเราเพื่อให้การจับคู่บางอย่างกับพีคมิเตอร์อื่นๆ (เช่น มิเตอร์ A ถึง D ที่คุณชื่นชอบ) คือการให้วิธีในการตั้งค่าตำแหน่งที่จะเกิดการเปลี่ยนสี การเปลี่ยนจากสีเขียวเป็นสีเหลืองอำพันสามารถตั้งค่าได้ และสำหรับโหมด 2 การเปลี่ยนจากสีเหลืองอำพันเป็นสีแดงด้วย สามารถทำได้จากแผงด้านหน้าโดยไม่ต้องถอดเครื่องออกจากชั้นวางหรือคลายเกลียวด้านบน (โหมด 3)

In order to provide some useful indication of A to D clip or overs, any green LEDS turn red, which is hard to miss. What is interest- ing, is that because the meter is looking at analog levels, one can see how many dBs the peak went beyond A to D clipping and this is also a good indication of how audible the clip was.

So to answer the question “Which one should I trust?” the best answer is “all of them with some interpretation and a grain of salt”. The VU is best to show apparent volume or apparent GR, the SLAM! peak meters show analog peaks, headroom in the SLAM!, and momentary GR that may or may not be audible. External digi- tal peak meters on the recording device should accurately display available headroom and clipping there. None of them are 100% accurate, nor implicitly perfect, and because each may have differ- ent response characteristics, might look different especially after a peak and the rates that dots fall and/or hold. If this is what you would like to calibrate, sorry.

LIMITERS

The first compressors we know of used special tubes designed for radio and gain control. These are the “remote cut-off” type like the 6386 as used in the Fairchild 670. Manley has been making the Vari- able Mu® compressor/limiter for many years based on the same principle.

Opto limiters probably began in the early 60’s with the UREI LA2A which used a small electro luminescent panel driven by audio di- rectly from a tube circuit. This panel was in a light shielded box with a photo-resistor so that when the panel lit, the light shone on the photo-resistor which in turn dropped in resistance and shunted audio to ground, and reduced its level. Very simple but effective technique which has stood the test of time. Part of the reason is the simplicity of the 2 knob approach and part is the inherent attack and release times both the electroluminescent panel and photo resistor have and part is the sound of the tube/transformer circuits.

มีบริษัทไม่กี่แห่งที่สร้างอุปกรณ์เครื่องเสียงระดับมืออาชีพในยุค 60 และ 70 แต่เรามีตัวจำกัด FET ทรานซิสเตอร์แบบแยกส่วนtage con- trolled amplifier (VCA) limiters, biased diode limiters and, in gen- eral, all had plenty of color and distortion. One of the best known FET based limiters is the UREI 1176 which brought more control to attack and release times and had ratio switches. The first few gen- erations of IC based VCAs were also less than perfect, and VCAs got a bad name but slowly improved over the years. With cheap easy to use op-amps และ VCA ราคาเกียร์ที่ลดลง ธุรกิจเพลงเติบโตขึ้น เราเริ่มเห็นอุปกรณ์มากขึ้น แต่อย่างใด 670 และ LA2As และ 1176 แบบโบราณยังคงใช้อยู่และเป็นที่ต้องการ

ในช่วงต้นยุค 90 ผู้ผลิตเครื่องเสียงที่ไม่ฝักใฝ่ฝ่ายใดรวมทั้งเราต่างก็ตอบสนองต่อความรู้นั้นและพัฒนาเทคโนโลยีเก่าใหม่ Manley สำหรับอดีตample began the ELOP® using a LED/photo resis- tor component called a Vactrol and combined it with ICs to drive it and tube circuits for the audio. Over the years, that opto circuit was revisited in a discrete transistor Langevin ELOP, variations on the theme used in the VOXBOX® and once again here in the SLAM!.

In developing the SLAM!, we began with the idea that probably we could find alternate Vactrols that could be used to give some variety to the opto-limiting. In the end, after trying every one out there, we decided the one we had always used, was our favorite and the oth- ers had more drawbacks than advantages. We did improve the drive and metering electronics, and added a HP filter in the side-chain and added the jacks to allow a user to insert their own EQ into the side- chain. In most aspects, the opto-limiter circuit is similar to the one used in our previous ELOP and uses audio to drive the LEDs. This means that we can’t possibly adjust the attack and decay character- istics significantly without changing Vactrols. On the other hand, this mode of operation, seems to act more like an RMS respond- ing circuit and reacts to many sounds in a way that we prefer over opto’s with the conventional attack, release, etc., controls and all the complications that a gain control element with its own timing char- acteristics adds to that recipe. To make a long story short, we like what happens with that simple old-school approach. The difference in driver circuits plus the side-chain filter does seem to make the opto a lot more useful on mixes and drums than our previous units. We also allow some fast LED metering of the opto in addition to the regular VUs which helps show how fast it tends to react and gives a more complete picture for critical applications.

“ตัวจำกัด FET”

Because we couldn’t improve much on our old opto circuit we de- cided to add a second ‘type’ of limiter with its own characteristics and its own historical roots. Some early limiters like the 1176 used FETs for the gain reduction element which offered much faster at- tack times and controllable releases.

The problem with FETs when used as a gain control element is that they can add unpleasant distortion unless the signal is very low (like

-30 to -40 dB) and we also wanted a few gain controls which also eat signal unless they are cranked. Throwing op-ampเพื่อให้ได้กำไรในจุดที่ต้องการนั้นง่าย แต่ไม่ใช่สไตล์ของเรา การรักษาแนวคิด Class-A แบบ all-tube ต้องใช้แนวทางที่แตกต่างกัน

เราใช้แนวทางใหม่และใช้หม้อแปลงไฟฟ้าเป็นส่วนหนึ่งของวงจรแบ่ง ซึ่งไม่เพียงแต่ลดสัญญาณให้อยู่ในระดับที่ดีสำหรับ FET แต่ยังทำให้เราสามารถใช้ FET คู่หนึ่งในเฟสตรงข้ามเพื่อลดความผิดเพี้ยน แนวทางที่มีราคาแพง แต่คุ้มค่า

Our main goal of the FET limiter was to achieve the fastest release that we could cleanly. This is the quality that causes the gain to return as fast as possible, which is what gives us our perception of ‘loudness’ .The goal here was a great ‘go-louder’ box. Fast at- tacks, and ∞ : 1 brickwall limiting is important to prevent ‘overs’ but not for increasing the average level. A very fast transient that gets through will clip but as long as the duration is short enough it will not be perceived as distortion. Very fast release times, unfortu- nately, usually imply modulation distortion where the limiter traces the waveform at low frequencies rather than the volume envelope. This is inevitable, but we made it possible to achieve faster and cleaner releases than usual. It can still get crunchy so be careful.

This FET sidechain uses several techniques to get those fast releas- es. The usual full-wave rectifier was replaced with a quadrature rec- tifier that uses 4 phases to determine peaks and allows twice as fast smoothing. Then we combine multiple side-chains and the typical exponential capacitor release was modified for linear decay rates. All of this resulted in faster clean releases, thus more loudness. Still, at the fastest release times it is quite possible to get modulation dis- tortion, which is sometimes a useful color and often a problem with wide spectrum sounds like mixes or instruments with lots of lows. Listen for a growly sounding distortion on faster release times.

The multiple side-chains also gave us the possibility of introducing an attack switch, which is usually not found on a limiter (com- pressors, yes). The attack switch works on the slowest side-chain, which gives much of the audible familiarity of the control while the other side-chains are still biting the fastest transients. Like most at- tack controls, as you go from fastest to slowest positions, you tend to lose some threshold or limiting, so adjusting the FET LIMITER threshold will probably be required, conversely more clockwise for VF settings.

A CLIP setting is on the release switch, that introduces a very rounded clipping with a variable threshold. This type of distortion is reminiscent of speaker distortion and tends to be mentally associ- ated with ‘loud’. Of course, more conventional clipping is possible and by turning up the INPUT, and turning down the OUTPUT, or if one wants ‘drastic’ switching to MIC or INSTRUMENT will do that of course. And, no, you won’t hurt anything as long as, phantom is off, and you prudently turned the OUTPUT down first. It wasn’t designed to simulate a guitar amp but intended to ‘assist’ an already overdriven tone. Mostly CLIP is used to get a few extra dB of ‘angry loud’.

‘Hyper-Compression’

The word ‘Hyper-compression’ is a word mastering engineers use and was coined by Lynn Fuston (Mastering Web Board, DSD vs 96/24). For many people it implies the idea of limiting and multi-band limit- ing and normalizing and squeezing every last drop of apparent volume possible onto a stereo mix but most mastering engineers would pre- fer not to. It has become almost a contest and everybody wants to be louder than everybody else. Record companies expect it, or ask for it and sometimes demand it. Mastering engineers are expected to do it and are given mixes so brutally squashed that they can’t get any louder anywhere without just clipping and distorting.

‘Maximizing’ level also implies ‘minimizing’ dynamics and transients. Dynamics and transients are one of the few available ‘elements’ in sound and music, with the others being pitch, duration and waveform. Very primitive music was just log drums and stretched animal skins, or mostly just transients and dynamics. It’s not hard to make ‘music’ with just transient information, but can you do it with just pitch (like a technician’s oscillator), or the one of the other two elements? Dynam- ics and transients are musical elements and not the enemy.

Maximizing levels very often results in a CD that can exhaust the lis- tener before the first song is over. It can produce an aggressive in-your- face constant barrage that might ไม่ be appropriate for every project, every song, and every artist. It might be like most effects, best used as an effect and where it is appropriate, sometimes full tilt and sometimes lightly. Super-squashing might also be going out of fashion, and we see a trend where producers are avoiding it.

การขยายใหญ่สุดทำได้ดีที่สุดที่การเรียนรู้ stage rather than during mix- ing, usually. We’ve heard these stories many times, “The A&R guy (or producer or artist) demanded that the engineer use a certain box to maximize the mix, so he did, but he also supplied the mastering engineer with an alternative version without that box. The mastering engineer did his best with both versions, and everybody preferred the results from the ‘raw’ tape and hated the maximized mix, and in the end the one from the ‘raw’ version was loudest anyway”. Never heard the opposite story. Why? Mastering engineers generally have the best tools, the most tools, and the right tools for the job, and a ‘pre-mas- tered’ job often robs the mastering engineer of the opportunity to apply those tools, and experience, and abilities. If you do use the SLAM! on a mix (before it gets professionally mastered) you should have a ver- sion without it and/or a version with light limiting. They also like 24bit masters, and a little headroom (like -3 to -6 dB below digital clipping) and lots of accurate labels/notes. Thank us later.

Maximizing generally does not help the song sound any louder on the radio or TV. Perhaps you know that they are old hands at that game and have compressors, 10 band limiters, 4 band limiters, full range limiters and clippers strapped across the audio chain all the time and have had for 15 years. Everything comes out the same volume – as loud as they can make it. Things can get silly because their boxes were set to work on ‘normal’ mixes and sometimes they get goofy when given super- squashed songs and songs that have lots of stereo or out-of-phase info. For them, width is bad, mono is good, it transmits further, gets bigger audience share, bigger ad bucks. Car CD players like over-compressed material and many now build a bad compressor into the car stereo, so this is covered too.

ดังนั้น สแลม! เป็นอีกกล่อง “GO-LOUDER” แต่มีป้ายเตือน เรากำลังสร้างปืน ไม่ใช่การเหนี่ยวไก เช่นเคย ใช้หู การตัดสินใจ และรสชาติของคุณ ระวังด้วยปืนใหญ่นี้

คำแนะนำ

Everybody knows that you should make those A to D peak meters go as hot as possible, digital full scale, but NEVER clip. Well, we have two urban myths in that statement. Often enough, the next thing after the A/D (filters, plug-ins, processors & EQs) requires a few dB of headroom and they might have a nasty distortion complete with aliasing if given digital full scale. It is caused by a little ripple in the pass band of the filter that actually can add a little bumps across the spectrum. The ‘better’ the filter the lower those bumps will be, but they add up. Most filters need between 1 to 3 dB of headroom. Some MPEG encoders need 6 dB. Don’t feel compelled to hit DFS if you are working 24 bit and going to master later. Resolution will be fine and a little headroom may be a nice thing 6 dB below DFS. Save almost DFS levels for mastering 16 bit/44.1 CDs that need every bit.

Yes, most early A/Ds sounded horrible when pushed into clipping and clacked, barked and complained loudly. Most modern A/Ds can be pushed a bit ‘over’ into clipping without obvious distortion and a few (especially older Ultra-Analog based ones) have a pleasant clip. You can certainly get a hotter mix, and more ballz with a little clip- ping (keyword being little) but our advice is to choose where and how to clip carefully. Usually analog clips better than digital and usually tube units clip better than solid state, but lots of tube boxes don’t sound good at all clipping (including some of ours). So, it requires experimentation, (on your time), careful level scaling, and careful listening to highs, lows, peaks and noise. If you do it right, maybe, make a master with level to rival the top mastering engi- neers, or do it a bit wrong and ruin the project, and have something you regret for a long time. It is not easy or automatic, and boxes that claim to do it usually don’t.

A large part of the trick to getting a hot loud mix is to watch the VUs. The idea is not to see how far the needle can bend to the right, but how still and immobile you can get it and still have it sound like music. Make that needle just sit there while mixing before you limit and then you just need to use a few dB of limiting and loud it will be. This is not so easy to do. Limiting individual tracks and sub-groups makes it easier. Start with the hottest tracks, which are usually vo- cals, bass and drums. This applies for basic limiters, multi-band lim- iters and de-essers. Each of these are harder to use effectively on a mix than an individual track or sub-group. On a mix, anything hot can trigger them and they affect everything. If you de-ess a mix, try not to mess up high hats, acoustic guitars & careful EQ settings. De-essing a lead vocal is relatively easy. Limiting a mix will prob- ably seem to affect the drums first, because in a typical mix drums are the source of most of the transient spikes. The initial attack or transient gets pulled down (spikes you probably liked during track- ing) but also everything else gets pulled down for that instant. So drums begin to sound more distant and feel pulled back in the mix (and you spent an hour fine tuning that part of the blend), they begin to sound dull (because the transient contains the bulk of their highs), and reverbs and room mics seem to get louder. When limiting hits vocals, some good things and some questionable things can happen. Plosives (Ps, Bs Ds Ks) might get hit and alter carefully sung pro- nunciations, but sometimes, after EQ, plosives need some taming. Some singers hit high notes a lot harder, and fader-riding, compres- sors or limiters are needed (hopefully, in that order). In the end, if individual tracks and sub-groups are limited first, then, not only is final limiting and mastering easier, but also it is easier to mix, as well as to create dynamics in the mix. By the way, vintage record- ings rarely used a buss compressor – its a fairly new trend. If you do limit the 2 buss, watch out for quiet sections and the drum balance in the mix, and use those ears.

Which brings up the first thing last. The traditional way to have loudness, dynamics, excitement and smoothness all at the same time is with that old tool called ‘arranging’. Take another listen to your favorite records and check out how they use many instru- ments to create loud or a few to create quiet or a relief. Listen to how solos & intro instruments sound great when not covered by everything else. If it happens to be a recording of great musicians playing together, listen to how they are their own automatic level control. This rarely happens with a mostly overdubbed song, but sometimes a great mix simulates it. Dynamics galore, but a con- stant level, hmmmmm.

การตั้งค่าที่เหมาะสมที่สุด

Sorry, we can’t really tell you where to set the knobs for female vo- cals, a strat, or next year’s standard mastering level. It all depends on the track and taste and the sound you are trying to achieve. We can give you a few guidelines and share some experience, if that helps.

Limiting can be more audible or difficult than on a well set up compressor given the same number of dBs of gain reduction. This is because limiting has a higher ratio and typically has faster at- tacks and releases. Old school engineers advise “to only limit a few dB on occasional peaks”, and this is good advice on most limiters. Hopefully, you will be able to limit a little deeper with the SLAM! without the usual problems. A limiter that shows, say, 5 dBs of re- duction, can sound louder than a compressor set for 1:1.5 ratio and dropping 10 dB almost steadily. Certainly during quiet passages, the compressor will seem louder, but the limiter can seem louder in the hotter passages when it is just grabbing transient peaks. The compressor might be smoother and more tolerant of settings, but won’t offer the protection and ‘drive’ of a well set up limiter. The compressor’s job is to reduce the difference between soft and loud in a smooth even way. The limiter’s job is to inaudibly stomp on the hottest transients, and prevent peaks from getting above a set threshold. It’s all in the names.

How can you tell when you have it set wrong and set right? There is no ‘wrong or right’ that applies to every day, but we can suggest the usual things an engineer listens for. You should experiment with some drastic settings when you are alone or can without scar- ing a client. There are 3 main things and the amount of reduction affects each of them, so it is worth trying some heavy-handed set- tings to imprint the symptoms to your audio memory.

The first is modulation distortion. When a limiter is set for dan- gerously fast releases, the bass waveform gets into the sidechain, causing the gain of everything to be changed on a low frequency cycle by cycle basis. The result is a ratty sort of distortion, not really bright and edgy like clipping, but usually not very pretty either, and often not very useful creatively. With the SLAM!’s FET limiter, you can easily set releases that are way too fast and cause modulation if there are any significant lows in the signal. The cure is slower releases, less limiting and/or slower attacks. Settings slower than 100mS are generally pretty safe but always listen.

With the Opto, modulation can happen with about 10 dB or more limiting on bass. You can use less limiting or try the side-chain filter switch. Keep in mind that the side-chain filter will prevent some limiting of loud low notes so there is a some risk of ‘overs’. The combination of both the Opto & FET can help share the load for tougher signals like mixes and can be a sweet combination.
The second typical problem setting for limiters and maybe even

more for the SLAM! is pumping. The worst case scenario is a mix that has a very hot transient followed by a significantly quieter few seconds. A limiter should grab the peak, shove the gain down sufficiently, then gradually return to normal gain. How gradually depends on where you set the release. If the limiter was set so that it reduced 20 dB, then that quiet passage may rise in level 20 dB over a short time. This can sound pretty weird depending on that quiet passage. Unfortunately, some of the moderate release times, like between 100mS and 500mS can be most obvious. Unfortunate because, these are typically optimal settings for loudness enhance- ment. Faster releases might distort and slower might tend to hold the gain down or sit between peaks or beats. We have known a few engineers to change release times on the fly, for transitions between big choruses and sparse verses that follow, and this can work better than any electronic or algorithmic ‘auto’ setting.

The third problem is not really so bad unless you are attempting to make the song loud. Releases set too long. When the release is very long, a transient, however brief, triggers gain reduction, and a bar later the gain is beginning to rise back to normal, and boom, another transient reduces the level again. You could have turned down a fader or final gain control and gotten the same effect. The SLAM! isn’t immune to this, but the slowest release is moderate at 2 seconds. Some limiters have much longer releases. 8 second releases tend to be safe and almost inaudible, but pulling a fader down a few dB before the song starts is very, very inaudible and does about the same thing. Sometimes the best thing, is to ride the fader, slowly, gently, then add the limiter for what it does best – extremely fast reaction.

นักร้อง can be a prime candidate for limiting. Perhaps the most used limiter ever for pop vocals is the vintage LA2A. The ELOP Limiter in the SLAM! recreates that action, and goes a few steps further with side-chain filters and FET limiter. Start with the ELOP typically on the 100 SC filter (or 200 if esses need a bit of extra taming), get the INPUT & ELOP LIMITER levels optimum, adjust for an optimum level to ‘tape’. Then maybe sneak in a bit of FET Limiting, with Attack at VF, RELEASE between 1 sec and 100 mS.

สำหรับ ผสม, we generally lean on the FET Limiter for most of the work. Releases again between 1 sec and .1s are OK, but .1s is verging on dangerous. Attack will be important. VF attacks will sound cleanest but less punchy. Adjust to taste and watch out for loss of drums at VF and distortion at M. Adding some ELOP will be subtle if more than 6 dB of FET limiting is used. We suggest using the 200 SC filter to tame highs and de-ess sometimes.

กีต้าร์ may like the FET CLIP setting for a bit of extra crunch. เบส may require slow releases, and VF attacks for ultra clean sounds, but for extra growl, there are quite a few settings that go there. Faster releases, deeper limiting, and slower attacks each contribute to various distortions, not to mention just overdriving levels. Piano is difficult usually, but try faster attacks, slower re- leases and not too much limiting.

กลอง – well, you just gotta play with the SLAM! to find the most appropriate sound. You can certainly tame dynamics, exaggerate room sound, crunch and mangle. Faster release times bring out the room sound and ambiance. It’s a bit drastic, but you can use one side of the SLAM! for mic-pre and limiting, go out to an EQ, and return to the other channel for yet more limiting, drive and A/D conversion. You might record that first channel as a minimally processed back-up too. Save something for the mix.

จำกัด และ จำกัด และอีกมากมาย ...

 

The following is a small section of the Orban Optimod-FM, 8400 owner’s manual. This is a compressor used by radio stations be- fore they broadcast the music signal. Orban is, by far, the leading company building broadcast limiters in the world. This eloquent piece posted on <rec.audio.pro> by Robert Orban serves as yet another warning for those that intend to use hyper-compression on their mix.

 

ในการเขียนนี้ มีแนวโน้มอย่างมากในการเรียนรู้ซีดีเพื่อนำระดับการประมวลผลเสียงไปใช้กับซีดีที่เคยใช้โดยสถานีวิทยุ "ที่มีการประมวลผลเชิงรุก" เท่านั้น ซีดีเหล่านี้ได้ยินผิดเพี้ยน (บางครั้งก็โจ่งแจ้ง) ก่อนการประมวลผล Optimod ใดๆ เพิ่มเติม ผลลัพธ์ของการประมวลผล 8400 อาจทำให้ความผิดเพี้ยนนี้เกินจริง และทำให้การบันทึกเหล่านี้ไม่เป็นที่พอใจในการฟังทางอากาศอย่างเห็นได้ชัด

 

There is very little that a radio station can do with these CDs other than to use conservative 8400 presets, which will cause loudness loss that may be undesired in competitive markets. There is a myth in the record industry that applying “radio- style” processing to CDs in mastering will cause them to be louder or will reduce the audible effects of on-air processing. In fact, the opposite is true: these CDs will not be louder on air, but they will be audibly distorted and unpleasant to listen to, lacking punch and clarity.

 

Another unfortunate trend is the tendency to put so much high frequency energy on the CDs that this cannot possibly survive the FM pre-emphasis/de-emphasis process. Although the 8400 loses less high frequency energy than any previous Orban processor (due to improvements in high frequency limiting

and clipping technology), it is nevertheless no match for CDs that are mastered so bright that they will curl แผงหน้าปัดรถไวนิล
เราหวังว่าอุตสาหกรรมแผ่นเสียงจะสัมผัสได้ถึงความรู้สึกเมื่อได้ยินผลที่ตามมาของการปฏิบัติเหล่านี้ในอากาศ อนิจจา ที่เขียนนี้ พวกเขาไม่ได้แสดงสัญญาณของการทำเช่นนั้น
Anyone—please feel free to quote anything I’ve posted on the board. I am trying to bridge the broadcasting and mastering communities, and the best way is to “get the word out.”
หัวข้อนี้เริ่มร้อนแรงขึ้นในรายการส่งเมลวิทยุเทคโนโลยี Broadcast.net วิศวกรการออกอากาศกังวลอย่างมากเกี่ยวกับเนื้อหาที่ถูกตัดและบิดเบี้ยวที่พวกเขานำเสนอ อันที่จริง ผู้โพสต์ที่ได้รับความนับถือคนหนึ่งได้เสนอข้อกำหนดอัตราส่วนสูงสุดต่อค่าเฉลี่ยขั้นต่ำสำหรับวัสดุที่จะถือว่าเป็น "คุณภาพการออกอากาศ" และเสนอให้สถานีปฏิเสธวัสดุใดๆ ที่ละเมิดข้อกำหนดนี้

ฉันทามติคือสถานีวิทยุต้องมีมิกซ์ที่ "ควบคุมด้วยวิทยุ" สิ่งเหล่านี้สามารถใช้ EQ และการบีบอัดทั้งหมดกับรีลีสมาตรฐานได้ แต่จำเป็นต้องมีการจำกัดสูงสุดและการตัดทอนหรือตัดทอนอย่างมาก สิ่งนี้จะคงรสชาติที่เพิ่มโดยการควบคุม แต่จะไม่บิดเบือน!

In this age of broadband Internet connections, it would be per- fectly feasible to service stations with “radio-mastered” singles from a password-protected webเว็บไซต์. สถานีส่วนใหญ่จะไม่ต้องการการบีบอัด fileเพื่อรักษาคุณภาพและป้องกันปัญหาใดๆ กับ “อัลกอริธึมการดวล” เนื่องจากสถานีมักจะบีบอัดในภายหลังในสายโซ่ ไม่ว่าจะเป็นเมื่อจัดเก็บเนื้อหาลงในฮาร์ดดิสก์สำหรับการเล่นออนแอร์ หรือในลิงก์ระหว่างสตูดิโอกับเครื่องส่งสัญญาณ (STL) ).

http://www.orban.com/

We completely agree with Robert’s post and the suggestion to cre- ate a few masters with lesser amounts of limiting. Hopefully the password protected web-ไซต์สามารถใช้งานได้ และผู้ผลิตและ/หรือบริษัทแผ่นเสียงสามารถโพสต์มิกซ์ที่ปรับให้เหมาะสมสำหรับวิทยุได้

บางทีโพสต์ของ Robert อาจมุ่งเป้าไปที่การใช้ตัว จำกัด แบบหลายวงในทางที่ผิด แต่ SLAM! สามารถทำไฮเปอร์บีบอัดและ/หรือบิดเบือนซึ่งอาจทำให้เกิดปัญหาในสายโซ่มากกว่าซีดีพื้นฐานสำหรับการฟังที่บ้าน มันไม่ง่ายอย่างนั้น สำหรับอดีตample, one might clip a track deliberately for a certain ef- fect or for apparent loudness. If during the song, a section has less highs, a station’s multi-band limiter may try to lift the HF bands, exaggerating the HF harmonic distortion and making it more than ugly. In fact, it might make it unplayable by some stations.

What might we suggest? Musicians might try to play at consist- ent volumes. Mix engineers might limit individual tracks and sub- groups more than the mix. They might also want to rely more on the mastering engineer for final limiting, and their expertise and experience with how product translates to broadcasting. Mastering engineers have to consider the broadcast chains. A&R people have to realize that songs sell records, and a louder CD won’t make much difference. In fact, a CD that is too loud, too aggressive, too in-your -face may also be too exhausting to listen to for more than one or two songs – but A&R guys don’t read manuals like this.

In more direct practical terms, run the mix 3 times and create 3 versions with different depths of limiting. This gives the mastering engineer more to work with. The mastering engineer can also do the same thing and create 3 masters. Then the only trick is making sure the right parties get the right version, without misdirection. Another idea mentioned earlier is limiting individual tracks, and sub-groups. One can also create loudness just in how tracks are mixed and EQ’ed. In fact, absolutely great mixes need very lit- tle or nothing done in mastering (everybody’s elusive goal). The worst mixes need the most processing. Slapping a drastic proces- sor on a bad mix is just that, and doesn’t make it a great mix or make real mixing easier or ‘mixing’ something that everybody can do as long as they have that drastic processor. Just gotta mix well first.

บางทีคำแนะนำที่ดีที่สุดคือการทำในสิ่งที่วิศวกรผู้มีประสบการณ์ทำมาเป็นเวลา 50 ปีกับลิมิตเตอร์ ใช้อย่างระมัดระวังและระมัดระวัง สองสามเดซิเบลอาจจะดีกว่าไม่มีเลย และดีกว่าจำกัด 10 เดซิเบล แน่นอนว่านี่หมายความว่าคุณต้องใช้หูและเมตรไม่ใช่ที่ตั้งไว้ล่วงหน้า แนวคิดไม่ได้จำกัดอยู่แค่ว่าคุณสามารถหลีกเลี่ยงได้มากเพียงใด แต่ควรจำกัดให้เหมาะสมเพียงใดและน้อยเพียงใดและยังคงฟังดูดีอยู่ คำตอบปกติคือ 2-6 dB ในการผสม (สมมติว่ามีเวลาโจมตีเร็วเท่านั้น)

In simple quick comparisons, we generally tend to prefer the choice that is louder and most people can be fooled into thinking X is ‘better’ than Y even with a fraction of a dB more volume. This is really one place where a bit of extended listening is required to determine which is actually better to listen to for any longer dura- tion. Transients and dynamics can be very nice too.

Maybe you were just thinking, how much (or little, right) should you limit the mix for the mastering engineer. So now you have to consider how much limiting is appropriate for the artist and song, how much is appropriate for the CD and that audience and how much is appropriate for radio, for the label, for vinyl dance tracks. If only one version is allowed – be careful, avoid regret- table squash.

THE GUTS

  1. ในการเปิด: Disconnect the AC Power cable, let sit 15 minutes to allow the power supply capacitors to discharge. Remem- ber there are high voltages (350VDC) used in the SLAM! and that the capacitors may continue to hold a charge after AC power and/or power supply connector is removed – Remove the two Phillips Machine screws located on the perforated top cover (towards the back). Slide the top cover out towards the back. There are 3 LEDS located towards the back and center. They indicate capacitor charge. If one is lit , wait for full discharge and the LED to completely go out, and then it is safe. ระวัง! We suggest using gloves and/or “one hand only” when the top is off when working on tube
  2. Replacing Tubes: The tubes are marked as to their type 12AT7 (for voltage gain) and 6414 (for line drivers). Another warning: Tubes get Let them cool before you attempt to touch them. Wiggle the tube back and forth as you pull it up. If you suspect a tube, you can swap it with the other channel. If the problem follows the tube, you were right, it is that tube. If not, try swapping another pair of tubes. It is a good idea to have a few spare tubes for emergencies as this will fix better than 90% of most problems.
  3. Trim Procedures. This is best done by a trained technician with access to specialized instruments like voltmeters and distortion Replacing a tube generally does not require a re-calibration. Without a distortion analyser, we suggest ‘no touchy’ the trims marked THD and BAL. The full factory calibration procedure is on the following page.
  4. Changing JUMPERS: There are 3 jumpers that allow for a little bit of user modification. The first is in the center and on the left side of the SideChain board. With this jumper IN (factory set), when STEREO LINK is selected, only the left side controls are active and are operating on a summed L&R (mono) signal. With no jumper here, both STEREO LINK and BOTH & EXT use both sets of controls. This mode is a similar to previous Manley compressors, best for mastering, but The second pair of jumpers are a grounding option and set whether the XLR outputs are PIN 1 grounded to Circuit Ground or Chassis Ground. These are factory wired for Chassis Ground, so that hum current is dumped to chas- sis. The XLR inputs are wired for Pin 1 = Circuit Ground because the Phantom Power return is carried on Pin 1 or ground reference.
  5. Replacing Meter Bulbs: New units like this use very long-life LEDS. For older units lamps are available from Manley (12 volt Festoon) and available from Selco part number 19-29-39/12V. You remove the two small Phillips screws (back, top, center) which allows you pull the white light cover panel away. Gently pry out the old bulb, insert the new one and screw the panel back Note that a few of the very first units used 26V lampและหากมีข้อสงสัย โวลต์จะถูกทำเครื่องหมายบนหลอดไฟ

สแลม! ขั้นตอนการจัดโรงงาน

เตรียม:

1) +4 dBu (1.23vAC), 1kHz Oscillator fed into XLR LINE INPUTS

  • UNBALANCED LINE OUTPUTS feed Level & Distortion
  • Select LINE on SOURCE, L&R LIMITERS off, Phantom
  • Set INPUT & OUTPUT LEVELS for 12:00.
  • Set ELOP LIMITER & FET LIMITER fully
  • Set SC Hz to FLAT, ATTACK to .1
  • Set LINK to DUAL MONO (off).
  • Set LED to PEAK, VU to I/P, VU to

พลัง

  • POWER UP supply toggle – verify zero AC amps on external Variac current meter.
  • POWER UP front panel POWER – spikes and settles to 5 amps.VU meters lit, POWER button lit RED. 3 internal LEDs lit. LED meter dances.
  • After 30 seconds mute relay
  • VU meters should read approximately 0
  • Adjust INPUT for 0 VU, which should be close to 12:00.

Tube Circuit Trims

  • Switch VUs to O/P. Disregard the reading for
  • Adjust LINE AMP The gain should SLOWLY rise and distortion should drop to below

.05% (-65) or around –70dB. It helps to set it so the plate volts are about 170vdc. As you adjust the trim watch the distortion and when it ‘nulls’, quickly note the plate volts then it is easier to trim for that voltage than for the distortion ‘null’ because of the slow speed of this trim.

(FET Drain/Tube Cathode ประมาณ 10-11vDC และตัวต้านทาน FET Source/2K ประมาณ 4.5-5vDC, แผ่นประมาณ 160-180vdc, ประตูประมาณ 27mvAC และรับประมาณ 34 dB สำหรับ s นี้tage.) Alternatively and assuming no test gear, the highest gain corresponds to the lowest distortion. This is a broad peak though and distortion may not be truly minimized but probably OK.

  • Adjust LINE AMP GAIN trim for 0VU (+4 dBu) with OUTPUT set to 12:00.
  • Verify distortion is nulled (or trim 2 is still at maximum gain)
  • Reduce Oscillator by 34dB (24.5mvAC), SOURCE select MIC. VUs should show near zero but won’t (no real trim for mic pre gain). Actually the INPUT pot typical +/-20% tolerance is worse than the gain stage errors.
  • Adjust MIC AMP BIAS trim for maximum gain & lowest distortion. This is also a slow mov- ing trim and THD&N should drop below .02% or –65dB. It helps to set it so the plate volts are about Noise and distortion may look similar in amplitude. VU should read between -2 to +2 (24.5mVAC=0VU). Boosting gain by 25dB, should show smooth clipping . 400-80k noise floor should be below –65 dB (-70 typical).
  • SOURCE SELECT = Ø. Verify Polarity does reverse (and was correct).
  • SOURCE SELECT = 100 Verify approximately 3dB down at 100 Hz.
  • Raise INPUT 16 dB (.154vAC). Change input cable to 1/4” plug and insert it fully into INSTRU- SOURCE SELECT = DI. OP should read about 0VU.
  • Pull 1/4” INPUT half way Signal should remain near 0VU
  • Pull 1/4” OUTPUT half way Signal should drop 12 dB (-10dBv)
  • SOURCE SELECT = Raise oscillator by 14dB (back to normal +4 dBu). Check BAL- ANCED output for level and distortion (distortion ‘null’ might drift on a new tube).
  • If using AP run a frequency Vs level test to verify flat

ลิมิตเตอร์ ทริมส์

OPTO LIMITER

+4 dBu (1.23vAC), 1kHz Oscillator fed into XLR LINE INPUTS.

  • VU select = Verify reading close to 0 VU.
  • L&R LIMIT =
  • Verify VU’s within 3 dB of Trim ZERO VU GR on Side-chain board so that VU = 0 with no gain reduction.
  • VU select = O/P. Set ELOP LIMIT threshold knob to 9:00 O’clock. VU’s should show some
  • Adjust OPTO GR trim for 4 dB of
  • VU mode = Adjust opto METER GR trim also for -4 dB displayed on VU’s.
  • VU mode = O/P Verify operation of STEREO LINK & BOTH&EXT
  • Run through SC Should see more GR at 100 and more at 200.
  • Return ELOP LIMIT fully CW (off), Return VU mode = O/P

FET LIMITER

+4 dBu (1.23vAC), 1kHz Oscillator fed into XLR LINE INPUTS
ขั้นแรกให้ทำ LED METER TRIMS ขั้นตอนที่ 1&2 เท่านั้น ! (ดูหน้าถัดไป)

 

  • Start with FET BIAS, FET BALANCE, FET LIMIT trims in (Main Board) RELEASE = .1s
    ATTACK = VF

FET LIMIT fully CW (off) LED = PEAK DUAL MONO. (no link)

  • Adjust FET BIAS for 1 dB of reduction.
  • Increase oscillator by 6 dB’s (Input = 10dBu)
  • Adjust FET LIMIT fully
  • Adjust FET BALANCE for maximum gain Usually trim will sit close to the center position. Trim will show minimum gain reduction in both sides of the trim.
  • Return FET LIMIT fully CW (off), Decrease Oscillator by 6 dB’s (Output = +4dBu) or (VU = 0)
  • ทำซ้ำขั้นตอนที่ 2 ถึง 6
  • Adjust FET BIAS for .1 dB ( or just at the threshold when reduction begins ).
  • FET LIMIT = 9:00 O’clock. Adjust GR for 4 dB of limiting (Output = 0 dBu )
  • LED = Adjust FET METER trim (sidechain board) for 4 Yellow segments lit.
  • Increase Oscillator by 6 dB’s Verify 12 Yellow segments lit (3rd dot from top).
  • Run through RELEASE settings. Should see deeper GR at ‘2 sec’ and less at 10mS in smooth steps with a jump at CLIP. With RELEASE at .1S, run through ATTACK settings, and should see less GR at F and less again at M.
  • Decrease Oscillator by 6 dB’s (VU = 0), Return FET LIMIT fully CW (off), Return VU = O/P.

LED Meter Trims (This is done in MODE 2)

  • With 0VU, adjust AUDIO PEAK trim (sidechain board) for 4 segments lit. Increase oscillator by 6 dB & Be sure L&R are even. Verify 10 segments lit (4th dot from top), adjust AUDIO PEAK trim if needed.
  • Kill oscillator verify no segments Verify -20 dB in lights the first segment.
  • Set LED to With FET LIMIT at 9:00 adjust for 4 Yellow segments lit. Be Sure L&R are even.
  • Use music to verify display is nice, balanced and no segments are Go through Mode 1 Peak and GR, verify in GR both FET and OPTO are displayed. Do the same for Mode 2 Peak and GR. 5) Go to Mode 3, verify LED TRIM (front panel) changes color change point. Leave trim in middle of range. (Factory default 3 Yellow led’s lit ) TO ADJUST :
    A.- Go to mode 3 (left bar lights)
    B.- Hit reset one more time fast.(left bar flashes) Adjust LED TRIM middle of range.
    C.- Hit reset one more time fast.(left bar stop flashes) Adjust LED TRIM for three yellow segments lit.
    D.- Go to mode 2. (Mode 2 Factory default)
  • Go to Mode 4, verify Peak, Peak Timed and Peak Hold (Mode 4 Peak Timed Factory default)
  • Power down, hold MODE TOGGLE down, and power up to return to default

Holding the toggle down as you turn power on resets the LED meter to factory defaults.
Holding the toggle down as the meter does its opening dance displays the software version. If the left display shows 3 LEDs and the right shows 2, you have LED Meter Software Version 3.2.

การแก้ไขปัญหา

มีอาการหลายอย่างที่เป็นไปได้ของบางอย่างไม่ถูกต้อง บางอย่างอาจเชื่อมต่อ อื่น ๆ เราจะสัมผัสเช่นกัน หากคุณสงสัยว่ามีปัญหา ย่อหน้าต่อไปนี้น่าจะช่วยได้
NO POWER, NO INDICATORS, NADA – Probably something to do with AC power. Is it plugged in? Check the fuse on the back panel. A blown fuse often looks blackened inside or the little wire inside looks broken or its resistance meas- ures higher than 2 ohms. A very blackened fuse is a big hint that a short occurred. Try replacing the fuse with a good one of the same value and size. If it blows too, then prepare to send the unit back to the dealer or factory for repair. The fuse is a protection device and it should blow if there is a problem. If the unit works with a new fuse, fine, it works. Some- times fuses just blow for unknown reasons.

LIGHTS BUT NO SOUND – First try plugging the in and out cables into each other or some other piece of gear to verify that your wires are OK. If not fix them or replace them. Assuming that cables passed sound – it probably is still a wiring thing. The output XLRs are transformer balanced which require both PIN 2 and PIN 3 to be connected some- where. When driving an unbalanced input ( inserts on some consoles) PIN 3 needs to be grounded or connected to PIN

  1. Same with the unbalanced 1/4 inch jacks – if driving a balanced input you can’t ignore the negative side. It needs to be connected to the sleeve of the phone plug. Another way to do basically the same thing is join PIN 1 and PIN 3 on the

XLR male at the destination. Easiest way – Use the balanced with balanced, unbalanced with unbalanced. That is why the options are there.
LEVELS SEEM TO BE WRONG, NO BOTTOM – Several possible scenarios. Manley uses the professional standard of +4 dBm = Zero VU = 1.23 volts AC RMS. A lot of semi-pro gear uses the hi-fi reference of -10 dBm = Zero VU. This is a 12 dB difference that will certainly look goofy and may tend to distort. The SLAM! has plenty of gain available on the INPUT control to accomodate -10 dBv and/or one can use the INSTRUMENT input. For -10dBv outputs, use the 1/4” unbalanced jack with the plug pulled out half way. If the loss looks close to 6 dB and it sounds thin then one half of the signal is lost. The cause is probably wiring again. One of the two signal carrying wires (the third is ground / shield on pin 1) is not happening. Check the cables carefully because occasionally a cable gets modified to work with a certain unit and it seems to work but its wrong in other situations. Sometimes on XLR transformer inputs like this unit one has to connect PIN 3 to PIN 1 and this is easy to do on the XLR cable (it happens with some unbalanced/balanced connections).

ONE SIDE WORKS FINE BUT THE OTHER SIDE IS DEAD – Let’s assume this is not wiring. We are pretty sure it is the SLAM. If it were solid state you would generally send it back for repair. Being a tube unit, you can probably find the problem and fix it yourself in a few minutes. Not too many years ago, even your parents could “fix” their own stuff by taking a bag of tubes down to the corner and checking the tubes on a tube tester – but these testers are hard to find today. A visual inspection can usually spot a bad tube just as well. Be careful – there are some high voltages inside the chassis and tubes can get pretty warm, but if you can replace a light bulb you should be able to cruise through this. Before you remove a tube, just take a look at them powered up. They should glow a bit and they should be warm. If one is not, you have already found the problem. The tube’s filament (heater) is burnt out or broken like a dead light bulb. The other big visual symptom is a tube that has turned milky white – that indicates air has gotten into the tube or we’ve joked “the vacuum leaked out”. Either way replace the tube. Manley can ship you a tested one for a reasonable price. Before you pull a tube, pull the power out, let the unit sit and cool and discharge for a minute or two, then swap the new tube in, then power, then check. Gentle with those tubes, don’t bend the pins by trying to insert the tube not quite right. A little rocking of them as you pull them out or put them in helps. If the problem follows the tube you found the problem – a bad tube. No soldering, no meters, one screwdriver – easy. See page 20 for a diagram of tube locations.

HUM – Once again – several possibilities – several cures. Most likely it is a ground loop. Ideally each piece of gear should have one ground connection and only one. However, the short list of grounds include the AC mains plug, the chassis bolted to a rack with other gear, each input and each output. The two most common procedures are: try a 3 pin to 2 pin AC adapter (about a dollar at the hardware store).This while legal in many countries can be dangerous- We went one better; Method two – On the back panel loosen the GROUND TERMINALS and slide the small metal ground strap to one side. This is way better than “method one” because it is safer and removes another possible source – the chassis

grounding via the rack. Method three – cutting the shield on one end of each cable. This is done by some studios at every female XLR to “break” all ground loops. All the other gear in the rack is “dumping” ground noise onto the ground. Try removing the SLAM! from the rack so that it is not touching any metal. You just may have cured a non-loop hum. Some gear radiates a magnetic field and some gear (especially if it has audio transformers or inductors) might receive that hum. A little distance was all it took. Also the remote power supply box will radiate a 60Hz magnetic field so it should be kept 6”-24” away from gear that may be sensitive.

IT MAKES NOISES WHEN THE FRONT PANEL IS TAPPED – An easy one. Some tubes become microphonic over time. That means they start acting like a bad microphone. Vibration has caused the supports for the little parts in the tube to loosen and now the tube is sensitive to vibration. Easy – Replace the tube. Which one? The one that makes the most noise when you tap it. Usually this will be one of the smaller (gain stage) tubes (12AT7A) closest to the front. The SLAM! will have to be on, connected and speakers up but not too loud for the sake of your speakers. With more gain comes more micro- phonics so be real about your expectations.

IT GOT HISSY – Also easy. This is again a common tube symptom. You could swap tubes to find the bad boy, but an edu- cated guess is OK too. Generally the first tube in the path is the one with the most gain and dealing with the softest signals. The usual suspect is the shorter tubes – the 12AT7A voltage ampลิตเตอร์ คุณอาจพบว่าคุณต้องเลือกท่อที่เงียบที่สุดจากหลายประเภทนั้น เช่นเดียวกับที่เราทำที่โรงงาน

ความแตกต่าง – This might be a tube. Swapping is a good way to find out. It may be a wiring thing or mismatch as well. Wiring problems usually accompany the distortion with a major loss of signal. Mismatches are a bit tougher. The SLAM! has a high input impedance and low output impedance that can drive 600 ohm inputs of vintage “style” gear. Best place to start ischeck your settings and meters. It may not be your first guess.

GETTING DISTORTION WHEN WE BOOST มาก. No doubt. The SLAM! by itself should have enough headroom but it has a lot of available gain. Also the VU attenuator might be at -6dB which hints that the next piece may be getting a very hot signal. You’re gonna have to turn something down, whether it is the signal feeding the SLAM!, the INPUT or OUT- PUT level or the input level of the next device. You might check that the FET RELEASE isn’t set on CLIP too.

DC OR SOMETHING AT THE OUTPUT THAT IS INAUDIBLE – The 1/4” unbalanced outputs have a frequency re- sponse that goes way down to below 1 Hz. A little very low frequency noise may be seen as speaker movement when moni- tors are pushed to extreme levels. The XLRs do not exhibit this because the transformers filter below 8 Hz. Also the unbal- anced outputs do not like long cheap high capacitance cable. Occasionally a very high frequency oscillation (200 kHz to 400 kHz) may occur in these conditions. Once again use the XLR outputs. Problem solved.

THE GAIN SEEMS OUT OF CALIBRATION – Wait a bit and see if it just needs to warm up. There are two trimmers inside for adjusting the gain of the two channels up or down a few dB. More than that and you either have a bad cable or bad tube. In MIC/DI modes there is a huge INPUT Level gain range and most pots do have 20% tolerance of position/value.

Once in a while we get a call from a client with a “digital studio” with confusion about levels. They usually start out by using the digital oscillator from their workstation and finding pegged VU meters the first place they look and they know it can’t be the workstation. Even a

-6 level from their system pegs the meters. Some of you know already what’s going on. That -6 level is referenced to “digital full scale” and the converter might have 18 or 18.5 or 20 dB of headroom built in. That -6 level on the oscillator is actually a real world analog +12 or +14 and those VU meters don’t really go much further than +9 attenuated. There are a few standards and plenty of exceptions. One standard is that normal (non-broadcast) VU meters are calibrated for 0VU = +4 dBm = 1.228 volts into 600 ohms (broadcast is sometimes

+8dBm). Another standard is that CDs have a zero VU analog reference that is -14 dB from digital full scale or maximum. This allows sufficient peak headroom for mixed material but would be a bad standard for individual tracks because they would likely distort frequently. This is why digital workstations use higher references like +16 and +20. A VU meter hits red (0VU) at +4 dBm, a digital peak meter hits red at about +18 dBm to +24 dBm. Peak meters and VU meters will almost never agree – they are not supposed to. A peak meter is intend- ed to show the maximum peak that can be recorded to a given medium. VU meters were designed to show how loud we will likely hear a sound and ‘help’ set record levels to analog tape- they are slower and supposed to approximate RMS levels. By ‘help’, we mean that they can be only used as a guide combined with experience. Bright percussion may want to be recorded at – 10 on a VU for analog tape to be clean but a digital recording using a good peak meter should make the meter read as high as possible without an “over”. Here is the second confusion: There aren’t many good peak meters. Almost all DATs have strange peak meters that do not agree with another company’s DAT. One cannot trust them to truly indicate peaks or overs. Outboard digital peak meters (with switchable peak hold) that indicate overs as 3 or 4 consecutive samples at either Full Scale Digital (DFS) are the best. They won’t agree with VU meters or Average meters or BBC Peak Programme (PPM) meters either. Each is a different animal for different uses. When in doubt, use the recorder’s meters when recording – they “should” be set up and proper for that medium. Also important – if your external DAC has gain trims, and these trims are “out” it can cause distortion, confusion, and a variety of mismatches. This is not the type of thing “phone support” is usually good at finding. We have seen guys spend thousands on new gear only to find out a little screwdriver trim would have solved their problems..

การเชื่อมต่อหลัก

สแลมของคุณ! ได้รับการตั้งค่าจากโรงงานเป็นแหล่งจ่ายไฟหลักที่ถูกต้อง voltagสำหรับประเทศของคุณ ฉบับที่tagการตั้งค่า e ถูกทำเครื่องหมายบนป้ายซีเรียล ซึ่งอยู่ที่แผงด้านหลัง ตรวจสอบว่าเป็นไปตามอุปทานในพื้นที่ของคุณ
หน่วยส่งออกสำหรับตลาดบางแห่งมีปลั๊กหลักแบบหล่อติดตั้งเพื่อให้สอดคล้องกับข้อกำหนดของท้องถิ่น หากเครื่องของคุณไม่มีปลั๊ก สายไฟสีควรเชื่อมต่อกับขั้วต่อปลั๊กที่เหมาะสมตามรหัสต่อไปนี้:

GREEN/YELLOW                 EARTH
BLUE                                       NEUTRAL
BROWN                                  LIVE

As the colors of the wires in the mains lead may not correspond with the colored marking identifying the termi- nals in your plug proceed as follows:
สายไฟที่เป็นสีเขียว/เหลืองจะต้องต่อกับขั้วต่อในปลั๊กซึ่งมีเครื่องหมาย E หรือสัญลักษณ์สายดินหรือสีเขียวหรือเขียวและเหลือง
สายไฟที่เป็นสีน้ำเงินจะต้องต่อกับขั้วต่อในปลั๊กที่มีตัวอักษร N หรือเป็นสีดำ
The wire which is colored BROWN must be connected to the terminal in the plug which is marked by the let- ter L or colored RED.

DO NOT CONNECT/SWITCH ON THE MAINS SUPPLY UNTIL ALL OTHER CONNECTIONS HAVE BEEN MADE.

หมายเหตุ: มีสายไฟหลัก voltage สวิตช์เปลี่ยนที่ช่วยให้ SLAM! กำหนดค่าได้ง่ายสำหรับวอลล์ผนัง 117V หรือ 220Vtagอี สวิตช์นี้อยู่บนแหล่งจ่ายไฟระยะไกลและต้องใช้ไขควงปากแบนเพื่อเปลี่ยน ควรทำโดยถอดสายไฟ IEC ออกเท่านั้น อย่าตั้งไว้สำหรับโวลุ่มผิดtage as this could damage the unit. Also, the fuse must change when one changes the change-over switch.
**สแลม! ใช้2 Amp ฟิวส์ SLO-BLO สำหรับ 117 โวลต์และ 1 amp ฟิวส์ SLO-BLO สำหรับ 220 โวลต์**
ขยะอุปกรณ์ไฟฟ้าและอิเล็กทรอนิกส์ (WEEE)

ข้อมูลสำหรับลูกค้า:

The European Parliament and the Council of the European Union have issued the Waste Electrical and Electronic Equipment Directive. The purpose of the Direc- tive is the prevention of waste of electrical and electronic equipment, and to promote the reuse and recycling and other forms of recovery of such waste. As such the Directive concerns producers, distributors and consumers.

The WEEE directive requires that both manufacturers and end-consumers dispose of electrical and electronic equipment and parts in an environmentally safe man- ner, and that equipment and waste are reused or recovered for their materials or energy. Electrical and electronic equipment and parts must not be disposed of with normal household wastage; all electrical and electronic equipment and parts must be collected and disposed of separately
ผลิตภัณฑ์และอุปกรณ์ที่ต้องรวบรวมเพื่อนำกลับมาใช้ใหม่ รีไซเคิล และการกู้คืนในรูปแบบอื่นๆ จะถูกทำเครื่องหมายด้วยสัญลักษณ์ต่อไปนี้:
ผลิตภัณฑ์ขนาดเล็กอาจไม่ถูกทำเครื่องหมายด้วยสัญลักษณ์นี้เสมอไป ซึ่งในกรณีนี้จะมีอยู่ในคำแนะนำในการใช้งาน บนใบรับรองการรับประกันและพิมพ์บนบรรจุภัณฑ์
เมื่อกำจัดอุปกรณ์ไฟฟ้าและอิเล็กทรอนิกส์โดยใช้ระบบรวบรวมที่มีอยู่ในประเทศของคุณ ถือว่าคุณปกป้องสิ่งแวดล้อม สุขภาพของมนุษย์ และมีส่วนช่วยในการใช้ทรัพยากรธรรมชาติอย่างรอบคอบและมีเหตุผล การรวบรวมอุปกรณ์ไฟฟ้าและอิเล็กทรอนิกส์และของเสียช่วยป้องกันการปนเปื้อนที่อาจเกิดขึ้นของธรรมชาติด้วยสารอันตรายที่อาจมีอยู่ในผลิตภัณฑ์และอุปกรณ์ไฟฟ้าและอิเล็กทรอนิกส์
ร้านค้าปลีก MANLEY หรือ LANGEVIN ของคุณจะให้ความช่วยเหลือและแนะนำวิธีการกำจัดที่ถูกต้องในประเทศของคุณ

ข้อมูลจำเพาะ

Input Tubes:                 2 x 12AT7A NOS GE specially selected by Manley Labs for lo-noise and stable bias Output Tubes:          2 x 6414W NOS USA dual triodes
I/O:                              MANLEY transformer coupled Balanced Inputs and Outputs
Micpre:                         Selectable 48V phantom power and PHASE REVERSE
Gain:                            60dB max Micpre, 43dB max DI, 20dB max Limiter Gain Input Impedance: 2000Ω Micpre, 1MegΩ DI
FET Limiter:                Attack: approx. 100μS; Release: 10mS to 2Sec; Ratio: better than 20:1 ELOP Limiter:            Attack: approx. 10mS for 6dB GR; Release: 2.5 Sec; Ratio: 10:1 Frequency Response:         5Hz to 60kHz
Maximum Output:       +32dBm, +30dBm (into 1KΩ load) THD+N:      <.05% @ 1kHz
Dynamic Range:           115dB typical Output Impedance:                                    200Ω
Power Consumption:    0.480 Amps (480 มิลลิวินาทีamps = 480mA) @ 120V = 57.6 วัตต์
0.240 Amps (240 มิลลิวินาทีamps = 240mA) @ 240V = 57.6 Watts Outboard Power Supply: factory-set for original destination country’s mains voltage.
แหล่งจ่ายไฟหลักฉบับที่tage: changeable with power transformer re-wiring via switch and fuse value change. Mains Voltage Frequency:50~ 60Hz Size: 19” X 12” X 3.5” (occupies 2u) Shipping Weight: 25 lbs.

ภาคผนวกสำหรับสแลม! รุ่นมาสเตอร์

The mastering version has a number of changes compared to the regular SLAM!:

  • There are no mic preamps or instrument inputs. Instead the tube sections are paral- leled for lower noise and distortion.
  • All pots are replaced with rotary switches for detented resettability and easier
  • The mastering version has a true hard-wire bypass function, which is not possible on the regular version with mic preamps ฯลฯ อะไรคือ Left Bypass กลายเป็น Bypass แบบเต็ม (ในแบบสเตอริโอและเดินสาย) ไม่มีปุ่มบายพาส L & R แยกจากกัน
  • The right BYPASS button becomes the Limiter Bypass (tubes & transformers still active)
  • There are dedicated unbalanced transformerless inputs on the mastering version. What was the Phantom Power switch on the back now selects XLR or 1/4”
  • The OPTO limiter now has 5 ratios, which may put it into the compressor/limiter The lower ratios may be better suited for complex mixes.
  • The FET limiter has 5 modes (these last two features replace the INPUT selector).

About item 6, the OPTO can be selected for 10:1, 5:1, 3:1, 2:1 and a new ‘AUTO HF’ mode where high frequencies get a higher ratio and low freqs get a low ratio. This mode is the most gentle. As with most compressors one might need to lower the threshold as one lowers the ratio, if keeping a similar depth of gain reduction is wanted. The threshold markings are based on the 10:1 ratio and a setting of +18 is intended to help reduce DFS overs with a converter with 14 dB of headroom over +4 dBm. Many mastering converters are set for 14 dB of headroom and the
+18 setting would be a good starting point. Of course being an Opto, it cannot be ultra-fast and some peaks will probably get through and it generally will have the typical (puffy) sound of an opto (because of its inherent time constants). It should be pointed out that much of that charac- ter is reduced when used in conjunction with the FET limiter. The FET usually catches some of the overshoots and time/gain behavior of the Vactrol and that can reduce the familiar Opto sonic signature.

The FET limiter has some subtle enhancements, some of which will not be apparent on all ses- sions. In particular, the LP LIM function will not be obvious unless the input signals are rather hot and more than a few dB of limiting is taking place. LP LIM is meant for those jobs that require more drastic treatments. If those conditions are met, 1) the NORM setting may be verg- ing on ‘crunchy’ and might seem dulled due to reduced transients, 2) the LP LIM setting can be less crunchy, and seem to have more ‘presence’ because the FET limiter won’t be pulling down as much mids and highs as it will lows where most of the energy is. It may also be difficult to compare NORM and LP LIM because the change involves a 3 or 4 second time constant. At normal levels, the two modes will be similar sounding. LP LIM seems to help in extreme cases where loudness is the prime goal. Use the Bypass button to check how much dynamic presence is added.

The 50% setting mixes some raw input with the post limiter signal, which is often difficult in a mastering environment. Because the FET side-chain senses right off the output XLR, one immedi- ate indication is significantly deeper gain reduction shown on the LED ladder, but less apparent limiting to our ears. In some ways, it is like reducing the ratio and threshold, maintaining a similar output level. It may sound a bit more open and may be useful where lower level passages need to be raised without killing all transients. Another benefit is that the raw parallel path flows through less circuitry.

การตั้งค่า CLIP เป็นเพียงการแนะนำวงจรซอฟต์คลิปที่ต่ำกว่า +18 dBv หรือประมาณ dB โดยประมาณที่ตัวแปลงที่ตั้งค่าไว้สำหรับ +14 ของ headroom อาจกระทบกับ DFS clipping วิธีนี้จะช่วยให้วาล์วนิรภัยอีกตัวหนึ่งมีพื้นที่ว่างเล็กน้อยเพื่อให้ตัวกรองดิจิทัลทำงานได้ดี บางคนอาจทำตามขั้นตอนนั้นด้วยตัว จำกัด แบบดิจิทัลเพื่อยกระดับให้ใกล้กับ DFS มากขึ้นหากต้องการ

You may notice that the ATTACK switch simulates some of the audible action we associate with attack controls on compressors but still tends to grab most of the fast peaks. In other words,
you get some punch with slower attacks. Like other attack controls you may have to adjust the threshold down at slower settings to maintain some clip protection, but may notice that you don’t have to adjust the threshold as much as one might expect with a conventional attack control. This is because there is a very fast limiter still hitting transients that are near our threshold of identify- ing.

Should also point out that the OPTO side-chain filter has some level compensation built in so that chopping off the lows, doesn’t cause a huge change in thresholds. There may be some
adjustment required depending on the spectral balance of the music though. With bright mixes the 200 Hz may actually cause deeper limiting, plus there is a 3 dB peak above 4K to help smooth excessive sibilance, though we don’t refer to it as a de-esser.

The hard-wire bypass function is not quite as trivial as might be expected. It is a bit more com- plicated because of 2 input jacks, plus the 2 different outputs, plus all the metering. Selection of either the XLR balanced (transformer) input or 1/4” unbalanced (op-amp) is done with a “pull to toggle” switch on the back panel. Like many of Manley’s processors, using the 1/4” unbalanced output bypasses the final transformer and may be a little cleaner or open sounding compared to the transformer output, which may be a little warmer and richer or evocative of some vintagอีเกียร์ อาจคุ้มค่าที่จะตรวจสอบอินพุตและเอาต์พุตแต่ละรายการในขณะที่คุณเรียนรู้หน่วยการเรียนรู้ ความแตกต่างที่ละเอียดอ่อนแต่สำคัญ

บางจุดได้รับแรงบันดาลใจจากความคิดเห็นแรกๆ จาก SLAM! ผู้ใช้ทำให้มันเป็นภาคผนวกนี้ด้วย

The SLAM! is designed primarily as an old school text book limiter and as such the Output Level knob is not after the final FET limiter. The idea is to set the peak-stop threshold and adjust the incoming level, which is why the level controls are larger. More fun is to be had adjusting the Input and Output Level controls than the Thresholds, which can often just be thought of as ‘set and forget’ especially if the FET Attack time tends to live in one setting. The Output level is not a ‘gain make-up’ control typical of a compressor but consider it as another Input level before the FET and after the Opto.

ทักษะหรือนิสัยบางอย่างที่เรามีกับซอฟต์คอมเพรสเซอร์ อาจมีประโยชน์น้อยกว่าเมื่อใช้ลิมิตเตอร์ สำหรับอดีตample, just setting it by ear, with similar input / output levels and an acceptable number of dBs of gain reduction or approaching it as an effect might not get the best results. The approach of trying to achieve a brick wall level and then tweaking how the unit is driven (those Input and Output knobs) usu- ally seems to work best. Put another way, limiters or limiting is not often a great effect in itself, but the increased volume when it is used reasonably can be. So it is about loudness rather than a cool pumping action, or pleasant warmth. It can do some of that, but was designed to be pretty clean for a tubed unit, and hot aggressive colors can be dialed in with the FET limiter.

The LED Gain reduction display is 1 dB per segment. We have seen numerous people at trade shows dial up 15-30 dB of gain reduction presumably to see a good number of LEDs flashing. It is still a limit- er and should be treated with some respect of the damage a powerful limiter in the wrong hands can do. In other words, it can be particularly vicious. The worst-case scenario is bass-heavy mixes, fast attack and releases, and deep limiting, where some GR modulation can happen. Though much has been done to allow those very fast releases, which maximize loudness, it does pay to be aware that distortions and edginess might be a side effect. Sometimes the best answer is exactly what many mastering engineers do daily, which is use 2 or 3 compressor/limiters each doing a few dB rather than one doing 10 dB. The LED meters can be very useful in comparing peak levels, especially when used with the Bypass button. Part of the secret to getting the most out of the SLAM!, is to learn the LED meter modes. Everybody has a favorite display mode, but they all are rather useful and you may find yourself changing modes more than expected. Of course, some rely too much on the meters and forget to listen and assume that particular operating levels are important. There is a healthy range of signal levels that are easily accom- modated. We only suggest using less limiting for the first few weeks until you are reasonably familiar with the unit. There is a learning curve and no real tricks or settings that seem to be common. Every mix may be different.

Lastly, it is not in any way like the Variable MU and was never intended to be. Each has its own purpose and special ‘unique talent’. The SLAM! may be easier to describe as a damn-fast transient killing secret weapon, or a tubed, analog L-2 with a buncha features, or maybe just a serious “go-louder box” with huge z. Enjoy!

 

 

อ่านเพิ่มเติมเกี่ยวกับคู่มือนี้และดาวน์โหลด PDF:

เอกสาร / แหล่งข้อมูล

MANLEY SLAM Stereo Limiter และ Micpre [pdf] คู่มือการใช้งาน
SLAM, Stereo Limiter และ Micpre, SLAM Stereo Limiter และ Micpre

อ้างอิง

ทิ้งข้อความไว้

ที่อยู่อีเมลของคุณจะไม่ถูกเผยแพร่