Installation Guide for LIEBHERR models including: FNc707i, FNd7026, FNC667I Tall Freezer, FNC667I, Tall Freezer, Freezer
Liebherr FNc707i No Frost Tall Freezer, White, C Rated | Marks Electrical
Liebherr FNd7026 No Frost Tall Freezer, White, D Rated | Marks Electrical
File Info : application/pdf, 12 Pages, 4.95MB
DocumentDocumentInstallation Guide Quality, Design and Innovation home.liebherr.com/fridge-manuals General safety instructions Contents 1 General safety instructions.................................. 2 2 Setup conditions................................................... 3 2.1 Space............................................................................. 3 2.2 Fitting the appliance into the kitchen unit.............. 3 2.3 Setting up multiple appliances.................................. 4 2.4 Electrical connection................................................... 5 3 Installation dimensions........................................ 5 4 Ventilation requirements...................................... 5 5 Water connection*................................................ 5 5.1 Dimensions for the water connection*.................... 6 5.2 Water pressure............................................................. 6 6 Transporting the appliance................................... 6 7 Unpacking the appliance...................................... 6 8 Mounting wall spacers.......................................... 6 9 Setting up the device............................................ 6 10 Setting up the appliance level.............................. 6 11 After setup............................................................ 7 12 Disposal of packaging........................................... 7 13 Reversing the door................................................ 7 13.1 Removing the door....................................................... 7 13.2 Moving the upper bearing parts to the other side. 8 13.3 Moving the lower bearing parts to the other side.. 9 13.4 Moving the handles to the other side*..................... 9 13.5 Fitting the door............................................................. 10 13.6 Aligning the door.......................................................... 10 14 Connecting the appliance to the water supply*.. 10 14.1 Connecting the hose*................................................. 11 14.2 Check the water system............................................. 11 15 Connecting the appliance..................................... 11 The manufacturer is constantly working to improve all types and models. Therefore, please be aware that we reserve the right to make changes to the shape, equipment and tech- nology. Symbol Explanation Read instructions Please read the information in these instruc- tions carefully to understand all of the benefits of your new appliance. Additional information online The digital manual with supplemental informa- tion and in additional languages can be found online by scanning the QR code on the front page of this manual or by entering the service number at home.liebherr.com/fridgemanuals. The service number can be found on the serial tag: Symbol Explanation Check appliance Check all parts for transport damage. If you have any complaints, please contact your agent or customer service. Differences These instructions apply to a range of models, so there may be differences. Sections that apply to certain models only are indicated by an asterisk (*). Instructions and results Instructions are marked with a . Results are marked with a . Videos Videos about the appliances are available on the YouTube channel of Liebherr-Hausgeräte. 1 General safety instructions - Please keep this assembly manual in a safe place so you can refer back to it at any time. - If you pass the appliance on, please hand this assembly manual to the new owner. - Read this assembly manual before installa- tion and use in order to use the appliance safely and correctly. Follow the instruc- tions, safety instructions and warning messages included at all times. They are important for ensuring you can operate and install the appliance safely and without any problems. - First read the general safety instructions in the "General safety instructions" section of the operating instructions, which accom- pany these installation instructions, and follow them. If you cannot find the oper- ating instructions, you can download the operating instructions from the internet by entering the service number at home.liebherr.com/fridge-manuals. The service number can be found on the serial tag: - Observe the warning messages and other detailed information in the other sections when installing the appliance: Fig. Example illustration DANGER indicates a hazardous situation, which if not avoided, will result in death or serious injury. 2 * Depending on model and options Setup conditions WARNING CAUTION NOTICE Note indicates a hazardous situation, which if not avoided, could result in death or serious injury. indicates a hazardous situation, which if not avoided, will result in minor or moderate injury. indicates a hazardous situation, which if not avoided, could result in damage to property. indicates useful advice and tips. - If you set up the appliance directly next to an oven, its energy consumption may increase slightly. This depends on the service life and how often the oven is used. - Always stand the appliance backed directly to the wall using the enclosed wall spacers (see below). 2.2 Fitting the appliance into the kitchen unit You can install kitchen cabinets around the appliance. 2 Setup conditions WARNING Risk of fire due to moisture! If live parts or the power cord get wet, this can cause a short circuit. u The appliance is designed for use in enclosed spaces. Do not operate the appliance in open space or in damp areas or where there is spray. Normal use - Only set up and use the appliance in enclosed spaces. 2.1 Space WARNING Leaking refrigerant and oil! Fire. The refrigerant contained within the appliance is envi- ronmentally friendly, but flammable. The oil contained within the appliance is flammable. Escaping refrigerant and oil can ignite if they are of high enough concentration and are exposed to an external heat source. u Do not damage the pipelines of the coolant circuit and the compressor. - The optimal installation site is a dry and well ventilated room. - If the appliance is installed in a very damp environment condensate water may form on the outside of the appli- ance. Always ensure sufficient airflow and ventilation in the setup location. - The more refrigerant there is in the appliance, the larger the space that it is installed in must be. If the space is too small, any leak may create a flammable mixture of gas and air. For every 8 g of refrigerant, the installation space must be at least 1 m3 . Specifications on the refrig- erant in the appliance can be found on the serial tag plate inside the appliance. 2.1.1 Installation surface - The floor of the installation site must be horizontal and level. - The height of the appliance base must be the same as the surrounding floor. 2.1.2 Installation position - Do no set up the appliance in an area with direct sunlight, next to a heating unit or similar. - You can set up the appliance directly next to an oven. Fig. 1 (1) Top cupboard * (2) Appliance * (3) Kitchen cabinet * (4) Wall * (A) Appliance depth * (B) Door depth * (C) Ventilation cross-section * (D) Distance to the rear of the appliance * (E) Distance to the side of the appliance * You can place the appliance directly beside the kitchen cabinet Fig. 1 (3).* There must be a ventilation shaft at the depth Fig. 1 (D) of the back of the top cupboard over the entire width of the top cupboard.* The cross section of the ventilation gap Fig. 1 (C) must be maintained below the ceiling.* If the appliance is set up with the hinges next to a wall Fig. 1 (4), the distance between the appliance and the wall must be at least 13 mm .* In order to be able to fully open the door, the appliance must protrude by the depth of the door Fig. 1 (B) from the front of the kitchen cabinet. Regardless of the depth of the kitchen cabinets Fig. 1 (3) and use of wall spaces, the appliance can protrude further.* * Depending on model and options 3 Setup conditions Appliances without handle / with recessed grip:* A 675 mm x B 75 mm C Min. 300 cm2 D mind. 50 mm E Min. 13 mm Appliances with lever handle:* A 675 mm x B 75 mm C Min. 300 cm2 D mind. 50 mm E Min. 57 mm x The use of wall spacers increases the dimensions by 15 mm (see 8 Mounting wall spacers) .* x The use of wall spacers increases the dimensions by 15 mm (see 8 Mounting wall spacers) .* Ensure that the following conditions are met: - Recess dimensions are adhered to . - Ventilation requirements are complied with (see 4 Venti- lation requirements) . 2.3 Setting up multiple appliances NOTICE Risk of damage caused by water condensate! u Do not install this device directly beside another fridge/ freezer compartment. These appliances are designed for different types of instal- lation. Only combine appliances if the appliances are designed for this. The following table shows the installation options by model: Fig. 2 (1) Top cabinet * (2) Appliance * (3) Kitchen cabinet * (4) Wall * (A) Appliance depth * (B) Door depth * (C) Ventilation cross-section * (D) Distance to the rear of the appliance * (E) Distance to the side of the appliance * You can place the appliance directly beside the kitchen cabinet Fig. 2 (3).* There must be a ventilation shaft at the depth Fig. 2 (D) of the back of the top cupboard over the entire width of the top cupboard.* The cross section of the ventilation gap Fig. 2 (C) must be maintained below the ceiling.* If the appliance is set up with the hinges next to a wall Fig. 2 (4), the distance between the appliance and the wall must be at least 57 mm . This is how far the handle protrudes when the door is open.* In order to be able to fully open the door, the appliance must protrude by the depth of the door Fig. 2 (B) from the front of the kitchen cabinet. Regardless of the depth of the kitchen cabinets Fig. 2 (3) and use of wall spaces, the appliance can protrude further.* Setup type Model Single All models Side-by-Side Model that start with S.... (SBS) Side-by-side All models without side wall heating with a space of 70 mm between the appliances Side-by-side with a space of 100 mm between the appliances Otherwise condensation will build up between the units. Fig. 3 Fig. 4 Assemble appliances according to separate installation instructions. 4 * Depending on model and options Installation dimensions 2.4 Electrical connection WARNING Danger of fire due to incorrect positioning! If the power supply cable or plug touches the back of the appliance, the vibration can damage the power supply cable or the plug resulting in a short circuit. u Make sure the power supply cable is not trapped under the appliance when you position the appliance. u Install the appliance so that it does not touch any plugs or power cables. u Do not connect any appliances to sockets in the area of the back of the appliance. u Do not place and operate power strips/power distribu- tors and other electronic devices (such as halogen trans- formers) at the back of the appliances. 3 Installation dimensions Dimensions with lever handle (mm): h a b' c' d' RB/a 42../i 1255 597 719x 654 1222x FN/b/c/d/e 42..(i) 1255 597 719x 654 1222x FN/c/d/e 46../i 1455 597 719x 654 1222x FN/c/d/e 50../i LTGN-234 1655 597 719x 654 1222x S/FN/d/c/sdd/std/bsd/sde 1855 597 719x 654 1222x 52../i LTGN-270 FN/c/d/e 66 ../i 1455 698 804x 754 1408x FN/c/d/e 70 ../i 1655 698 804x 754 1408x FN/c/d/e 72 ../i 1855 698 804x 754 1408x x For appliances with supplied wall spacers, the dimension must be increased by 15 mm (see 8 Mounting wall spacers) . 4 Ventilation requirements NOTICE Risk of damage due to overheating in the case of insuffi- cient ventilation! In the case of insufficient ventilation, the compressor can be damaged. u Make sure there is sufficient ventilation. u Observe the ventilation requirements. If the appliance is integrated in a fitted kitchen, the following ventilation requirements must be met: - The spacing fins on the back of the appliance are used to ensure sufficient ventilation. These must not lie in cavi- ties or recesses in their final installation position. - Basically, the larger the ventilation gap, the more energy the appliance saves during operation. Fig. 5 Dimensions without lever handle (mm): h ab cd RB/a 42../i 1255 597 675x 609 1215x FN/c/d/e 42.. GN 42Ve04 / GN 42Vd24 1255 597 675x 609 1215x FN/c/d/e 46../i GN 46Ve05 / GN 46Vd25 1455 597 675x 609 1215x FN/c/d/e 50../i GN 50Ve06 / GN 50Vd26 1655 597 675x 609 1215x S/FN/d/c/sdd/std/bdd/sde 1855 597 675x 609 1215x /sfd 52../i GN 52Ve07 / GN 52Vd2i FN/a/c/d/e 66 ../i 1455 698 760x 710 1402x FN/c/d/e 70 ../i 1655 698 760x 710 1402x FN/c/d/e 72 ../i 1855 698 760x 710 1402x 5 Water connection* If your appliance has a fixed water connection, a hose is supplied with it.* Note You can purchase a hose of a different length as an acces- sory.* Overview of dimensions (see 5.1 Dimensions for the for the water connec- water connection*) * tion:* Requirements for the (see 5.2 Water pressure) water pressure: Make the water connec- (see 14 Connecting the appli- tion: ance to the water supply*) * Depending on model and options 5 Transporting the appliance 5.1 Dimensions for the water connec- tion* u Remove the mains cable from the back of the appliance. Also remove the cable holder, otherwise there will be vibration noise! Fig. 6 (a) Maximum available hose length (b) Maximum available hose length (c) Distance of solenoid valve to floor (M) Solenoid valve a b c ~ 1300 mm ~ 950 mm ~ 150 mm 8 Mounting wall spacers With the wall spacer, your appliance will achieve the speci- fied energy consumption and no condensation will form in high ambient humidity. The appliance will work properly without using the wall spacer, but with a slightly higher energy consumption. If you use the wall spacer, the appliance depth increases by approx. 15 mm. u Appliance with supplied wall spacers: Fit wall spacers on the rear of the appliance at the bottom left and right. 5.2 Water pressure The water connection line and solenoid valve of the appli- ance are suitable for a water pressure of up to 1 MPa (10 bar). To ensure that the appliance functions correctly (flow rate, ice cube size, noise level), maintain the following water pressure: Water pressure:* bar* 1.5 to 6.2 MPa* 0.15 to 0.62 If the pressure is higher than 6.2 bar: u Connect a pressure reducer. u Make the water connection. (see 14 Connecting the appli- ance to the water supply*) 9 Setting up the device CAUTION Risk of injury due to heavy appliance! u Have two people transport the appliance to its installa- tion site. WARNING Danger of injury and damage due to the appliance being unstable! The appliance can tip over. u Secure the appliance as described in the instructions. 6 Transporting the appliance Observe the following when transporting the appliance: u Transport the appliance upright. u Use two people when transporting the appliance. During the first use: u Transport the appliance packaged. During appliance transport or at first use (e.g. when moving or cleaning): u Empty the appliance. u Secure the door against undesired opening. WARNING Danger of fire and damage! u Do not place devices that give off heat, e.g. microwaves, toasters, etc. on the appliance. Make sure that the following requirements are fulfilled: q Only move the appliance when it is not loaded. q Only set up the appliance when someone is present to help you. 10 Setting up the appliance level 7 Unpacking the appliance If the appliance is damaged check with the supplier immedi- ately before connecting it. u Check the appliance and packaging for damage during transport. If you suspect any damage, please contact your supplier immediately. u Remove all materials that could prevent it from being installed properly or prevent proper ventilation from the back or the side panels of the appliance. u Remove all protective films from the appliance. Do not use sharp or pointed objects for this. CAUTION Risk of injury or damage from the appliance tipping or the door falling open! If the additional adjustable foot on the base support is not correctly positioned on the floor, there is a risk of the door falling open or the appliance tipping. This can lead to injury or property damage. u Unscrew the additional adjustable foot on the support until it reaches the floor. u Then turn it another 90°. 6 * Depending on model and options After setup u Align the appliance so that it stands firmly and by applying the accompanying spanner to the adjustable height feet (A) and using a spirit level. u Then prop up the door: Lower the adjustable foot on the bearing bracket (B) until it contacts the floor, then turn it an additional 90°. WARNING Danger of injury due to door falling out! If the bearing parts are not screwed on tightly enough, the door may fall out. This can result in serious injuries. In addi- tion, the door may not close causing the appliance to cool improperly. u Screw on the bearing brackets/bearing pins tightly with 4 Nm. u Check all screws and retighten them if necessary. u Then prop up the door: Screw out the adjustable foot on the bearing bracket (B) using the open-ended wrench SW10 until it comes into contact with the floor, then turn an additional 90°. 11 After setup u Pull off the protective film from the outside of the housing.* u Pull off the protective film from the trim strips. u Pull off the protective film from the trim strips and drawer fronts. u Take off the protective film from the stainless steel rear panel. u Remove all transport packaging. u Clean the appliance. (see operating instructions) u Note the type (model, number), appliance designation, appliance/serial number, purchase date and dealer's address. NOTICE Risk of damage to side-by-side appliances caused by condensate! Certain appliances can be set up as side-by-side combina- tions (two appliances beside one another). If your appliance is a side-by-side appliance: u Install the SBS combination in accordance with the accompanying sheet. If the configuration of appliances is specified: u Do not change the door stop. 12 Disposal of packaging WARNING Danger of suffocation from packaging materials and films! u Do not allow children to play with packaging materials. The packaging is made from recyclable materials: - Corrugated card/cardboard - Parts made of foamed polystyrene - Films and bags from polyethylene - Packing bands from polypropylene - Wood frame nailed together with a polyethylene window* u Take the packaging material to an official collection point. Fig. 8 Observe the reading direction. 13.1 Removing the door Note u To prevent food items from falling out, take all food out of the door racks before removing the door. NOTICE Risk of damage! If the door seal is damaged the door may not close properly and the level of cooling is insufficient. u Do not damage the door seal with the screwdriver! 13 Reversing the door Tools u Remove the outer cover. (1) u Disengage and release the bearing bracket cover. Remove the bearing bracket cover. (2) u Unlatch the panel with a slotted screwdriver and swivel it to one side. (3) Fig. 7 * Depending on model and options 7 Reversing the door 13.2 Moving the upper bearing parts to the other side Fig. 10 u Remove both screws with a T20 screwdriver. u Lift and remove the bearing bracket. Fig. 9 CAUTION Risk of injury if the door tips out! u Keep a steady grip on the door. u Set the door down carefully. u Carefully remove the protective cover. Fig. 9 (1) u Loosen the bolts slightly with a T15 screwdriver. Fig. 9 (2) u Hold the door and remove the bolts with your fingers. Fig. 9 (3) u Pull the bearing bush out of the guide. Insert from the other side and latch into place. Fig. 9 (4) u Lift the door and place it to one side. u Carefully lift the plugs out of the door bearing bush with a slotted screwdriver and remove them. Fig. 9 (5) Fig. 11 u Take off the cover to the front from above. Fig. 11 (1) u Rotate the cover 180° and clip onto the other side from the right. Fig. 11 (2) u Latch the cover into place. Fig. 11 (3) u Position the upper bearing bracket. Fig. 11 (4) u Insert the screw with a T20 screwdriver and tighten it. Fig. 11 (5) 8 * Depending on model and options Reversing the door u Insert the screw with a T20 screwdriver and tighten it. Fig. 11 (6) 13.3 Moving the lower bearing parts to the other side 13.4 Moving the handles to the other side* Fig. 12 u Unscrew the metal plate, move it to the other side and screw it on again. Fig. 12 (1) u Put back the cover on the other side. (1) * Depending on model and options Fig. 13 u Pull off the cover. Fig. 13 (1) u Remove the screws with the T15 screwdriver. Fig. 13 (2) u Remove the handle. Fig. 13 (3) u Carefully lift up the side plugs with a slotted screwdriver and pull them out. Fig. 13 (4) u Insert the plugs again on the other side. Fig. 13 (5) 9 Connecting the appliance to the water supply* u Fit the protective cover to protect the door: Insert the protective cover and check that it lies flush on the door. If not, insert the bolt fully. Fig. 15 (3) u Insert the plugs. Fig. 15 (4) 13.6 Aligning the door WARNING Danger of injury due to door falling out! If the bearing parts are not screwed on tightly enough, the door may fall out. This can result in serious injuries. In addi- tion, the door may not close causing the appliance to cool improperly. u Screw the bearing brackets on firmly with 4 Nm. u Check all screws and retighten them if necessary. Fig. 14 u Position the handle on the opposite side. Fig. 14 (1) w The screw holes must be exactly above each other. u Tighten the screws using the T15 screwdriver. Fig. 14 (2) u Position the covers on the side and push them on. Fig. 14 (3) w Ensure that they latch into place correctly. 13.5 Fitting the door u Align the doors flush with the appliance housing using the two slots in the lower bearing bracket, if needed. To do this undo the middle screw in the bottom bearing bracket with the T20 tool supplied. Undo the remaining screws a little with the T20 tool or with a T20 screwdriver and align via the slots. u Prop up the door: Screw out the adjustable foot on the bearing bracket using the open-ended wrench SW10 until it comes into contact with the floor, then turn an addi- tional 90°. 14 Connecting the appliance to the water supply* Make sure that the following requirements are fulfilled: q The dimensions for the water supply connection are known and complied with. q The correct water pressure is maintained. q Water is supplied to the appliance via a cold water pipe that can withstand the operating pressure and is connected to the drinking water supply. q All equipment and devices used for the water supply comply with the applicable regulations in the country of use. q The back of the appliance is accessible so that you can connect the appliance to the drinking water supply. q You are using the supplied hose. Old hoses have been disposed of.* q The hose connector contains a screen filter with a seal.* q There is a faucet between the hose line and the domestic water connection so that you can turn off the water supply if necessary.* q The faucet is not directly behind the appliance and is easily accessible. This way, you can push the appliance as close as possible to the wall and can quickly turn off the faucet if necessary.* Fig. 15 u Place the door on the bottom bearing pins. u Align the top of the door with opening in the bearing bracket. Fig. 15 (1) u Insert the bolt and tighten with a T15 screwdriver. Fig. 15 (2) WARNING Risk of electric shock from water! u Before connecting to the water hose: Disconnect the appliance from the mains. u Before connecting to water lines: Shut off the water supply. u Make sure that only qualified personnel connect the device to the drinking water supply. WARNING Risk of poisoning due to contaminated water! u Connect to potable water supply only. 10 * Depending on model and options 14.1 Connecting the hose* Connecting the appliance u Tighten the nut Fig. 16 (4)clockwise with the tool Fig. 16 (5) until the maximum torque is reached and the tool Fig. 16 (5) no longer tightens. w The hose is connected to the appliance. Connecting the hose to the faucet: u Screw the nut Fig. 16 (7) onto the faucet Fig. 16 (8). Fig. 16 WARNING Danger of cuts if the tool is broken! u Only use the tool Fig. 16 (5) at room temperature. u Tighten the nut Fig. 16 (7)clockwise with the tool Fig. 16 (5) until the maximum torque is reached and the tool Fig. 16 (5) no longer tightens. u Hook the lug Fig. 16 (6) into the tool Fig. 16 (5). u Fasten the lug Fig. 16 (6) to keep it on the hose. w The hose is connected to the faucet. 14.2 Check the water system Before you completely install the appliance, Liebherr recom- mends checking the water system for leaks. u Slowly turn on the faucet.* u Check the hose, water feed and connections for leaks. w The water system has now been checked for leaks. w The water system is not leaking: You can install up the appliance completely. Note IceMaker: Before the first use, you must clean the IceMaker. (see Quick Start Guide or operating instructions)* Fig. 16 (1) Solenoid valve: The solenoid valve is at the bottom on the back of the appliance. It has an R3/4 connecting thread. (2) Cover (3) Angled hose end (4) Nut (5) Tool (6) Lug (7) Straight hose end (8) Faucet NOTICE Risk of damage from incorrect installation! u Do not damage or kink the hose. u Do not damage or kink the hose when setting up the appliance. Connecting the hose to the appliance: u Pull off the cover Fig. 16 (2). u Push and hold the nut Fig. 16 (4) all the way over the angled hose end Fig. 16 (3). NOTICE The solenoid valve will not be tight if the thread is damaged! If the solenoid valve is not tight, water may leak out. u Observe the following instructions for fitting the nut on the solenoid valve. u Carefully position and hold the nut Fig. 16 (4) on the sole- noid valve Fig. 16 (1). u Screw the nut Fig. 16 (4) onto the thread by hand until it is firmly in place. WARNING Danger of cuts if the tool is broken! u Only use the tool Fig. 16 (5) at room temperature. 15 Connecting the appliance WARNING Danger of fire due to incorrect connection! Burns. Damage to the appliance. u Do not use an extension cord. u Do not use a multipoint connector strip. NOTICE Danger of damage to incorrect connection! Damage to the appliance. u Do not connect the appliance to a stand-alone inverter, e.g. solar power systems and petrol generators. Note Only use the mains cable supplied. u A longer mains cable can be ordered from Customer Service. Make sure that the following requirements are fulfilled: - The type of current and voltage at the installation site complies with the information on the serial tag . - The socket is grounded and fused in accordance with regulations. - The tripping current for the fuse is between 10 and 16 A. - The socket is easily accessible. - The socket is not located behind the appliance but in areas a or b (a, b, c). u Check the electrical connection. u Insert the appliance plug (G) on the rear side of the appli- ance. Ensure that they latch into place correctly. u Connect the mains plug to the power supply. w The Liebherr logo appears on the screen. w The display switches to the standby symbol. * Depending on model and options 11 home.liebherr.com/fridge-manuals Freezer Issue date: 20240312 Part number index: 7088530-00 Liebherr-Hausgeräte Ochsenhausen GmbH Memminger Straße 77-79 88416 Ochsenhausen DeutschlandAntenna House XSL Formatter V7.3 MR5 Windows : 7.3.6.62109 (2023-09-14T17:58 09) Antenna House PDF Output Library 7.3.1871