Techbee Plug-in Electrical Meter Socket Electricity Usage Monitor

1. สินค้าหมดview

The Techbee Plug-in Electrical Meter Socket is an advanced device designed to help you monitor and manage your electricity consumption. It provides comprehensive data on various electrical parameters, allowing you to identify energy-intensive appliances and optimize your power usage for energy saving and environmental protection.

Figure 1.1: Techbee Plug-in Electrical Meter Socket Electricity Usage Monitor (Model JK-PM04) with its packaging.

คุณสมบัติหลัก:

• Energy-saving and Environmental Protection: Measures power consumption and calculates total energy costs for rational electricity planning.
• Multi-functional Monitoring: Offers 11 display modes including power (Watt), total energy used (kWh), carbon emissions (CO₂), voltage (Volt), current (Amp), frequency (Hz), power factor, cost per kWh, minimum power, and maximum power.
• Multi-layer Protection: Features warning indicators (screen flash and LED) for preset power, energy cost, or consumption limits. Default overload limit is 3680W, with a recommendation to set it to 1800W for initial use.
• User-friendly Display: Large, easy-to-read display set at a 45-degree angle for optimal visibility.
• Partial Reset Function: Allows deletion of measurement data without affecting original settings (e.g., cost/kWh).
• แบตเตอรี่ในตัว: Retains settings and measured data even when unplugged.

2. การตั้งค่าและการใช้งานเบื้องต้น

Follow these steps to set up your Techbee Power Meter:

1. การแกะกล่อง: Carefully remove the power meter from its packaging.
2. ฟิล์มป้องกัน: A transparent protective film is present on the screen. You may remove it for clearer visibility or keep it as preferred.
3. เปิดเครื่อง: Plug the meter directly into a standard electrical wall socket. The display should illuminate. If the screen remains blank or buttons are unresponsive, plugging it into a live socket will resolve the issue as it powers the internal battery and display.
4. Initial Overload Setting: The default overload power limit is 3680W. Before using the energy meter, it is recommended to set the overload power to 1800W for general household appliances. Refer to Section 3.2 for instructions on setting alarm thresholds.
5. เชื่อมต่ออุปกรณ์: Plug the appliance you wish to monitor into the socket on the front of the power meter.

Figure 2.1: The meter features a large display and a built-in battery for convenience.

3. คู่มือการใช้งาน

The Techbee Power Meter features four control buttons: โหมด, ชุด, UP, และ ลง.

3.1. โหมดการแสดงผล

กดปุ่ม โหมด button to cycle through the 11 different display modes. Each mode provides specific electrical data:

1. Watt / Total Cost: Displays current power consumption in Watts and accumulated cost.
2. Total kWh Used: Shows the total kilowatt-hours consumed.
3. Carbon Emissions (CO₂): Displays CO₂ emissions based on energy consumption.
4. เล่มที่tage / ความถี่: แสดงปริมาณกระแสไฟฟ้าtage (V) and frequency (Hz) of the power supply.
5. Current / Power Factor: แสดงค่าปัจจุบัน (Amp) and power factor.
6. Cost per kWh: อนุญาตให้ตั้งค่าและ viewing the cost per kilowatt-hour.
7. พลังงานขั้นต่ำ: Shows the lowest recorded power consumption.
8. กำลังสูงสุด: Shows the highest recorded power consumption.
9. โอเวอร์โหลดปลุก: Displays the set overload power limit.
10. Alarm of kWh: Displays the set kWh alarm limit.
11. Alarm of Cost: Displays the set cost alarm limit.

รูปที่ 3.1: เกินview of the 11 monitoring modes available on the device.

3.2. Setting Alarm Thresholds and Cost

To set specific values like cost per kWh or alarm limits:

1. กดปุ่ม โหมด button until you reach the desired setting mode (e.g., "Cost per kWh", "Overload Alarm", "Alarm of kWh", or "Alarm of Cost").
2. กดปุ่ม ชุด button. The digit you can adjust will start flashing.
3. ใช้ UP และ ลง ปุ่มเพื่อปรับค่า
4. กด ชุด again to move to the next digit or to confirm the setting.
5. เมื่อตั้งค่าตัวเลขทั้งหมดเสร็จแล้ว ให้กด โหมด เพื่อออกจากโหมดการตั้งค่า

Figure 3.2: The device provides visual alarms (flashing LED and screen indicators) when set thresholds are exceeded.

3.3. การรีเซ็ตข้อมูล

The meter allows for partial data reset, which means you can clear accumulated measurement data (like total kWh or total cost) without losing your custom settings (like cost per kWh or alarm thresholds). To reset measurement data, press and hold the ลง button for approximately 5 seconds until the relevant data clears.

3.4. Monitoring Appliance Consumption

The meter can precisely detect power usage down to 0.5W, allowing you to identify even the tiniest standby power consumption from your devices. This helps in tracking and reducing unnecessary electricity usage across various household appliances.

Figure 3.3: The power meter can be used to track consumption of various household appliances.

4. การบำรุงรักษา

To ensure the longevity and accurate performance of your Techbee Power Meter, follow these maintenance guidelines:

• การทำความสะอาด: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the display or casing.
• พื้นที่จัดเก็บ: เก็บมิเตอร์ไว้ในที่แห้งและเย็น หลีกเลี่ยงแสงแดดโดยตรงและอุณหภูมิที่สูงหรือต่ำเกินไป
• แบตเตอรี่: The meter includes a built-in Lithium Metal battery. This battery is not user-replaceable and is designed to retain settings and data when the device is unplugged.
• หลีกเลี่ยงความชื้น: Do not expose the device to water or high humidity. It is designed for indoor use only.

5 การแก้ไขปัญหา

If you encounter any issues with your Techbee Power Meter, refer to the following common problems and solutions:

6. ข้อมูลจำเพาะ

7. การรับประกันและการสนับสนุน

Techbee stands behind the quality of its products. This product comes with a รับประกัน 1 ปี ตั้งแต่วันที่ซื้อสินค้า

For any questions, technical assistance, or warranty claims, please contact Techbee customer service. We offer lifetime customer service to ensure your satisfaction with our products.

You can find more information and support resources by visiting the official Techbee store: Techbee Store on Amazon.